• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.3
• /
• pp.305-312
• /
• 2017

This paper presents a laboratory investigation into the effects of fillers using industrial by-product such as coal ash, IGCC slag on properties of hot-mixed asphalt concrete variation with filler content. For comparison, existing mixture with lime and dust have also been considered. Marshall and flow test has been considered for the purpose of mix design as well as evaluation of mixture. Other performance tests such as indirect tensile strength test, tensile strength ratio(moisture susceptibility), dynamic stability have also been carried out variation with filler content. It is observed that the mixes with industrial by-product exhibit conform with quality standard. Therefore, it has been recommended to utilize industrial by-product based on fly ash wherever available, not only reducing the produce cost but also partly solve the industrial by-product utilization and disposal problem.

• International Journal of Highway Engineering
• /
• v.6 no.4 s.22
• /
• pp.65-73
• /
• 2004

Marshall stability and flow don't reflect mechanical property of asphalt mixtures and have little correlation with rutting-related performance. There is often rutting occurred on the asphalt pavement which was constructed using a mixture passing the specification for stability and flow. This study dealt with comparison of volumetric properties of mixtures from Marshall mix design and from Superpave mix design. This study used one binder, three aggregates and two gradations. The mixtures were manufactured by each mix design method. Result showed that OAC, VMA and VFA by Marshall mix design were higher than those by Superpave mix design. This is because Mashall mixture has the gradation prone to rutting and it should be further investigated whether or not the high OAC is direct cause of rutting in asphalt pavement.

• Applied Chemistry for Engineering
• /
• v.25 no.4
• /
• pp.409-413
• /
• 2014

This study was carried out to design the optimum mixing ratio of aggregate, cyclic aggregate, and binder (moisture, emulsified asphalt, and emulsion type additives) and produce recycling cold asphalt paving mixture satisfying site work standard. The cyclic aggregate satisfying KS F 2572 was collected from waste asphalt by adequate processing. As the moisture content increased, the shearing strength was decreased. The maximum marshall stability was shown at the 3.0 wt% moisture content. So the optimum moisture content was 3.0 wt%. The marshall stability and flow value with the amount of emulsified asphalt was satisfied in the range of 0.5~2.5 wt%, and the porosity was satisfied in the range of 0.7~2.5 wt%. So the optimum amount of emulsified asphalt was 1.6 wt%. The optimum amount of emulsion type additive was 0.1 wt% in the light of marshall stability and degree of saturation of recycling cold asphalt mixture.

• 한국방재학회:학술대회논문집
• /
• 2009.02b
• /
• pp.141.1-141.1
• /
• 2009

• 한국도로학회:학술대회논문집
• /
• 2006.03a
• /
• pp.113-117
• /
• 2006

• International Journal of Highway Engineering
• /
• v.6 no.4 s.22
• /
• pp.13-24
• /
• 2004

The Marshall mix design method used in Korea, which was described in the design & construction regulation, had been introduced from Japan Highway Cooperation standard guide. Most engineers have thought that it is the major reason that causes pavement distresses. Therefore, there is a need to modify the current Marshall mix design through using the volumetric design concept, which is most widely used in asphalt mix design. The modified mix design determines the preliminary optimum asphalt content at 4% VTM (Voids in Total Mix). If the Marshall properties, which are VFA, VMA, stability, and flow, were satisfied with the requirements, the preliminary optimum asphalt content is determined as the final optimum asphalt content. The modified Marshall mix design considers VMA. while the current Marshall mix design does not consider VMA. By considering the Marshall stability and flow as the criteria instead of design factors, the modified Marshall mix design is able to decrease the errors occurred in Marshall stability test The test was performed to compare the Marshall properties between current and modified Marshall mix design. The left results showed that there was no difference in the Marshall properties, except for VTM. Thus, the modified Marshall mix design can produce the asphalt mixtures with the constant VTM (4%), and it can improve the asphalt mixture quality in Korea.

• 한국도로학회:학술대회논문집
• /
• 2002.10a
• /
• pp.89-92
• /
• 2002

The objective of this research is to evaluate engineering properties of recycled aggregates, slag as coarse & fine aggregate and waste foundry sand(WFS) as fine aggregate, in hot mix asphalt(HMA). In this research, soundness, gradation and particle analysis, abrasion, specific gravity and absorption test were carried out. The optimum asphalt binder content(OAC) for various HMA combinations of recycled aggregate was determined by Marshall Mix Design. The ranges determined is between 7.2% and 7.5%. Indirect tensile test, resilient modulus test, creep test were carried out for characterization of rutting behavior of various combination of HMA. Judging from the limited tests, the HMA with recycled aggregates is not as good rutting resistance as the HMA with common aggregates. After finishing the Wheel tracking test, the application or feasibility for the use of recycled aggregate as asphalt paving material will be determined.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3D
• /
• pp.425-433
• /
• 2006

The presented work provided a predictive equation for dynamic modulus of hot mix asphalt, which showed higher reliability and more simplicity. Lots of test result by UTM at laboratory has been used to develop the precise predictive equation. Evaluation of dynamic modulus for 13mm and 19mm surface course and 25mm of base course of hot mix asphalt with granite aggregate and two asphalt binders (AP-3 and AP-5) were carried out. Superpave Level 1 Mix Design with gyrator compactor was adopted to determine the optimum asphalt binder content (OAC) and the measured ranges of OAC were between 5.1% and 5.4% for surface HMA, and around 4.2% for base HMA. The dynamic modulus and phase angle were determined by testing on UTM, with 5 different testing temperature (-10, 5, 20, 40, & $55^{\circ}C$) and 5 different loading frequencies (0.05, 0.1, 1, 10, 25 Hz). Using the measured dynamic modulus and phase angle, the input parameters of Sigmoidal function equation to represent the master curve were determined and these will be adopted in FEM analysis for asphalt pavements. The effect of each parameter for equation has been compared. Due to the limitation of laboratory tests, the reliability of predictive equation for dynamic modulus is around 80%.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.178-178
• /
• 2011

도로소음은 다양한 소음원에 의해 발생하며, 도로를 이용하는 사람과 도로 주변사람에게 큰 불편을 초래한다. 보다 쾌적한 환경을 원하는 현대인에게 있어 도로 소음의 경감은 중요한 환경 공해로 작용한다. 도로 소음을 줄이기 위해서는 여러 가지 방법이 있을 수 있으며, 이 중 도로 포장의 개선을 통해 도로 소음을 경감할 수 있으며, 이와 같은 포장을 저소음 포장이라고 한다. 저소음 포장은 주행하는 차량의 타이어와 노면이 마찰하면서 발생하는 소음을 최소화하기 위한 것으로 소음 발생의 메커니즘을 바탕으로 하고 있다. 저소음 포장중 가장 널리 사용되고 있는 방법은 공극을 늘리는 것이다. 약 20%의 공극은 타이어와 노면 사이의 에어펌핑음을 최소화 하며, 소리를 흡수하는 역할로 약 3dB의 소음 가소 효과가 있는 것으로 알려져 있다. 소음을 감소시키는 또 하나의 방법은 노면의 표면 조직을 매끈하게 하여 타이어와 노면의 충격음을 줄이는 방법이다. 노면의 평탄성을 개선하기 위해 포장에 사용되는 골재의 최대크기를 줄이는 소입경 포장을 소음 가소의 목적으로 유럽 등지에서 많이 사용되고 있다. 본 연구에서는 이와 같은 저소음 기능을 위해 공극률을 크게 하고 소입경 골재를 사용하는 소입경 저소음 포장의 현장 적용을 위한 배합 설계를 수행하였다. 소입경 저소음 포장의 최대 골재 크기는 현장 적용성과 경제성을 고려하여 10mm 골재를 사용하였으며, 수도권에서 입수한 4곳의 산지 골재를 분석하여 골재 합성 입도를 산정하였다. 10mm 저소음 포장의 골재 입도 범위는 공극률 15~18%를 목표로 하며, 이를 만족하기 위하여 배합 설계를 수행한 결과 5mm 통과 중량 백분율이 약 30%로 하는 개립도가 적당한 것으로 나타났다. 공극이 증가함에 따라 포장의 내구성 향상을 위해 사용된 고점도 바인더는 아스팔트 혼합물의 생산 및 시공온도를 증가시키게 된다. 또한 굵은골재의 비율이 높은 개립도 아스팔트 혼합물의 경우 운반과정과 포설 과정에서 온도가 빨리 떨어지는 단점이 있다. 이를 극복하기 위하여 중온 첨가제의 사용을 통해 생산 및 다짐온도를 낮추고자 하였다. 소입경 저소음 포장의 배합설계 과정은 배수성 포장의 배합설계 과정과 유사하나, 칸타브로 손실률과 흐름실험의 변곡점을 기준으로 할 경우, 칸타브로 손실률과 흐름 손실률이 매우 작아 변곡점을 판단하기 어렵기 때문에 칸타브로 손실률과 흐름 손실률의 기준 만족 여부로 판별하고, 최적 아스팔트 함량은 공극률을 기준으로 산정하는 것이 바람직할 것으로 판단된다. 중온 첨가제를 사용할 경우는 중온 첨가제로 인한 점도의 변화를 감안하여 혼합 및 다짐 온도를 결정하고 배합 설계를 수행하며, 중온 첨가제의 특성과 양에 따라 최적 아스팔트 함량이 변화하게 된다.

• Resources Recycling
• /
• v.9 no.3
• /
• pp.37-45
• /
• 2000

This paper presents the experimental test results on moisture and freeze-thaw resistance of hot mix crumb rubber modified (CRM) asphalt concrete mixture. To compare the differences in mechanical properties of conventional and CRM asphalt concretes, various tests were conducted under different moisture conditions and freeze-thaw cycles. Marshall mix design was also performed to determine the optimum asphalt contents for the both asphalt concrete mixtures. Test results revealed that the moisture and freeze-thaw resistance of CRM asphalt mixture was superior to the conventional asphalt concrete. As a result, it is considered that the utilization of waste tires in asphalt pavements has the potential of minimizing the damage due to the moisture and freeze-thaw.