• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.7
• /
• pp.939-944
• /
• 2018

Clean fire extinguishing agents refer to chemical that can replace Halon 1211 and Halon 1310 according to the Montreal Protocol fermented to protect the Earth's ozone layer. In Korea and abroad, system standardization and performance evaluation of clean fire extinguishing agents are being carried out. This paper proposes an optimal nozzle shape by modeling and numerical analysis of various nozzle shapes based on general clean fire extinguishing system. The ejection speed of the nozzle can be improved by studying three - dimensional modeling of the nozzle for two shapes, Type A and B. Flow analysis was performed on the two types of nozzles and the gas velocity and pressure distribution were measured with different nozzle diameters. It was confirmed that the jetting speed was changed at the nozzle outlet according to the number and diameter of the nozzle holes. The flow rate increased with increasing the pressure regardless of the nozzle hole diameter. Based on the results obtained from the experiment, the K-factor value was deduced. Finally, a nozzle with a 12-hole structure with a 5-mm nozzle hole was proposed.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.357-360
• /
• 2006

In the present study, the air jet flow characteristics of the dryer in the automatic car wash machine were numerically predicted by commercial CFD code. The effects of the dryer shape and the nozzle width variations on the performance of the automatic car wash machine were discussed. To optimize the geometric parameters, the response surface method(RSM) with CFD was used. Predicted jet velocity distributions for the optimized geometry were compared with experimental data and the comparisons show generally good agreements. Also, the performance of the dryer was improved with the optimized results.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.5
• /
• pp.34-40
• /
• 2007

An optimization approach is investigated for the design of new nozzle system in a automatic car wash machine. Three-dimensional computational fluid dynamics and design of experiment methods have been employed to know the mutual interaction between the nozzle shape in the automatic car wash machine and the airflow velocity distribution on the vehicle surface. The performances of air nozzle system were defined as the velocity magnitude and the uniformity of the velocity on the surface of the car. Predicted jet velocity distributions for the optimized geometry were compared with experimental data and the comparisons showed generally good agreements. Also, the performance of the dryer was improved with the optimized results.

• Journal of Energy Engineering
• /
• v.19 no.3
• /
• pp.163-170
• /
• 2010

The objective of this study is to investigate the combustion characteristics of dual type of sintering burner as a function of design parameters using lab-scale sintering burner through experimental and numerical approaches. Combustion characteristics were evaluated by the radical method. The numerical model was verified as a temperature using R type of thermocouple at the bed surface. The effect of nozzle distance and angle were performed through the CFD analysis, and the comparison of burner types. As a results, dual type burner has more wider and uniform flame distribution than single type burner. Asymmetry and 45 degree angle condition have been suggested as an optimal condition for the ignition of the sintering bed surface.

• Journal of Animal Environmental Science
• /
• v.11 no.2
• /
• pp.111-116
• /
• 2005

The purpose of this study was to analyze the performance of vehicle disinfector nozzles using at the livestock farm. The nozzle of vehicle disinfectors was measured spraying rate and equality distribution ratio by pressures. The spraying rate of TK-I's nozzle was 1,605 ml/min at 3 MPa, TK-II's nozzle was 2,020 ml/min, JA's nozzle was 1,150 ml/min and IS's nozzle was 795 ml/min. The number of nozzles of TK-I's, TK-II's, JA's and IS's for reasonable spraying rate($25{\ell}/min$. at 3 MPa) was respectively 16, 13, 22 and 32 units. The equality distribution ratio of TK-I's nozzle by pressures was equalized and the nozzles of TK-II's, JA's and IS's was sprayed to the center or side more then other sides in the measured boxes.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.58.2-58.2
• /
• 2010

FPD (Flat Panel Display) 제조 공정에서 사용되는 패턴은 수 ${\mu}m$ 수준까지 감소하였으며, FPD의 크기는 급격하게 대형화 되여 현재 8세대(2200mm*2500mm)에 이르고 있다. 이에 따라, $1\;{\mu}m$ 이상의 크기를 갖는 오염입자에 의한 수율 저하를 극복하기 위한 세정효율의 향상 및 다량의 초순수 사용에 따른 폐수 발생으로 인한 환경오염, 또한 장비의 크기에 따른 공간 효용성 감소와 이에 따른 공정 비용의 증가 등의 어려움에 직면하고 있다. 따라서, 현장에서는 고효율, 저비용의 세정 공정 기술 개발에 대한 연구가 활발히 진행되고 있다. 이러한 문제점들을 해결 하고자 이류체 노즐 세정 장치와, 화학액 린스를 위한 초순수 Spray, 건조 공정에 해당하는 Air-knife, Halogen lamp로 구성된 소형화 된 고속 FPD(Flat Panel Display) 세정기에 대한 연구를 진행 하였다. 이류체 노즐은 초순수와 $N_2$ 가스를 내부에서 혼합하여 액적(Droplet)을 형성하여 고압으로 분사시키는 장치로서 화학액을 사용하지 않고 물리적인 방법으로 오염입자를 제거한다. Spray는 유기 오염입자 제거를 위한 오존수의 린스 공정을 위해 설치 하였다. 세정 후 표면에 남아있는 기판의 액막(water film)은 고압의 가스를 분사하는 Air-knife를 통해 제거하였으며, 고속 공정시 발생할 수 있는 Air-knife에서 제거하지 못한 잔류 액막을 Halogen lamp를 사용하여 효과적으로 제거함으로써, 물반점(water mark) 없는 건조 공정을 얻을 수 있었다. 실험에는 미세 입자의 정량적인 측정을 위하여 유리 기판 대신에 6인치 실리콘 웨이퍼(P-type (100))를 사용하였으며, > $\;1{\mu}m$ 실리카 입자를 스핀방식을 사용하여 정량적으로 균일하게 오염하였으며, 오염물의 개수 및 분포는 파티클 스캐너 (Surfscan 6200, KLA-Tancor, USA)를 사용하여 분포 및 개수를 정량적으로 측정 하였다. 이류체 노즐은 $N_2$ 가스의 압력과 초순수의 압력을 변화시켜 측정하여, 각각 0.20 MPa, 0.01 MPa에서 최적의 세정 결과를 얻을 수 있었으며, 건조 효율은 Air-Knife의 입사 각도와 건조면 간격, 할로겐 램프의 온도를 조절 하여 최적의 조건을 얻을 수 있었다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.3
• /
• pp.41-47
• /
• 2006

Effects of mean flow and nozzle damping on acoustic tuning of a gas-liquid scheme coaxial injector are investigated numerically adopting a linear acoustic analysis. The injector plays a role as a half-wave acoustic resonator for acoustic damping in a combustion chamber of a liquid rocket engine. As Mach number of mean flow in a chamber increases, the resonant frequency of the first tangential mode decreases slightly and the optimum injector tuning length varies negligibly. Nozzle damping affects neither the resonant frequency nor the optimum length. From these numerical results, effects of mean flow and nozzle damping on acoustic tuning of a resonator are negligible. As open area of the injectors increases, the acoustic amplitude decreases, but new injector-coupled modes appear.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.3
• /
• pp.41-47
• /
• 2013

This study was carried out to improve the design of fuel injection nozzle for marine medium speed diesel engine. For this purpose, fuel injection nozzle was modeled and simulated using CATIA V5R19 and FLUENT & MSC Nastran. Analyses of flow and heat transfer, respectively, were performed to find the optimal design of fuel injection nozzle. As the results, big pressure drop, which may lead to cavitation damage, was occurred at inlet of fuel injection hole with diameter 0.3mm. Furthermore, it was confirmed that the increase of mean temperature of fuel injection nozzle was almost a half in comparison with that of fuel injection nozzle tip.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.6
• /
• pp.589-604
• /
• 2021

Waterjets for rocks have various advantages of the non-contact and eco-friendly excavation using only water and abrasive. To overcome the problems (e.g., dust and noise occurrence) of the conventional drilling methods, waterjet excavation methods are broadly used. It is advantageous to operate a couple of nozzles in order to increase the waterjet excavation efficiency. When multiple nozzles are used, it is essential to analyze the excavation performance and shape according to the nozzle operation method. In this study, nozzle angle, horizontal distance between nozzles, and standoff distance were defined as nozzle operating parameters and the excavation performance and shape were analyzed. As a result of the experiment, when the nozzle angle and standoff distance are increased, the excavation depth is decreased and the effective depth tends to be increased. In addition, based on the experimental results, the excavation shape criteria required for nozzle insertion were proposed and optimal nozzle operating parameters were derived according to the criteria. This study result is expected to be used as useful basic research in the future development of multiple waterjet nozzles for rock drilling.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.4
• /
• pp.53-60
• /
• 2003

CCD(Charge-Coupled Device) wafers, with a layer of micro lenses on top, usually are not passivated with dielectric films. Micro lenses, in general, are made of polymer material, which usually has a large affinity for particles generated in the various chip fabrication processes, most notably the wafer sawing for chip-dicing. The particles deposited on the micro lens layer either seriously attenuate or deflect the incoming light and often lead to CCD failure. In this study we introduce new type of saws which would significantly reduce the particle-related problems found in conventional type of saws. In the new saws, the positions and diverging angles of side and center nozzles have been optimized so as to flush the particles effectively. In addition, an independent nozzle is added for the sole purpose of flushing the generated particles. The test results show that, with the new saws. the ratio of the particle-related CCD chip failures has been dropped drastically from 9.1% to 0.63%.