• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.251-251
• /
• 2021

최근 기후변화로 인한 집중호우의 영향으로 홍수 시 댐으로의 유입량이 설계 당시보다 증가하여 댐의 안전성 확보가 필요하다(감사원, 2003). 이에 건설교통부(2003)는 기후변화와 댐 노후화에 대비하여 치수능력증대사업을 추진하여 댐의 홍수배제능력을 확보하였고, 환경부(2020)에서는 40년 이상 경과된 댐을 대상으로 스마트 안전관리체계 구축을 통한 선제적 보수보강, 성능개선 및 자산관리로 댐의 장수명화를 목적으로 댐의 국가안전대진단을 추진하고 있다. 이에 본 연구에서는 댐 시설(여수로)의 노후도 평가 시 활용 될 수 있는 여수로 표면손상 원인규명에 대하여 3차원 수치모형(FLOW-3D 및 COMSOL Multiphysics)을 통해 검토하고자 한다. 연구대상 댐은 𐩒𐩒댐으로 지형 및 여수로를 구축하였으며, 계획방류량(200년 빈도) 및 최대방류량(PMF) 조건에서 모의를 수행하였다. 수치모의 계산의 정확도 검토를 위하여 Baffle의 설치를 통하여 시간에 따른 유량의 변화를 설계 값과 비교하였고 오차가 1.0% 이내를 만족하는 것을 확인하였다. 여수로 표면손상의 다양한 원인 중 기존연구(USBR, 2019)를 통하여 공동침식(Cavitation Erosion) 및 수력잭킹(Hydraulic Jacking)에 초점을 두었으며 방류조건 별 공동지수(Cavitation Index)산정을 통하여 공동침식 위험 구간을 확인하였다. 이음부의 균열 및 공동으로 인한 표층부 콘크리트의 탈락현상을 가속화시키는 수력잭킹 검토를 위하여 국부모형을 구축하였고 음압력(Negative Pressure), 정체압력(Stagnation Pressure), 양압력(Uplift Pressure)의 분포를 확인하였다. 최종적으로 COMSOL Multiphysics를 통하여 압력분포에 따른 구조해석을 수행하여 폰 미세스(Von Mises) 등가응력 및 변위를 검토하여 콘크리트의 탈락가능성을 확인하였다. 본 연구는 여수로 공동부 및 균열부에서의 손상메커니즘을 확인할 수 있는 기초적인 연구이지만 향후에는 다양한 지형조건 및 흐름조건에서의 압력분포 분석 및 유체-구조물 상호작용(Fluid-Structure Interaction, FSI)모의를 수행한다면 구조물 노후도 및 잔존수명 평가에 필요한 손상한계함수 도출이 가능할 것으로 기대된다.

• Horticultural Science & Technology
• /
• v.31 no.3
• /
• pp.317-321
• /
• 2013

This study was conducted to investigate the antimicrobial effect of freely available chlorine (FAC) on the vase life of cut rose 'Brut' (Rosa hybrida L.). Postharvest treatments to extend the vase life of cut roses were divided into holding solution treatment and pulsing solution treatment. In holding solution treatment, the cut roses were treated with the preservative solutions containing FAC (0, 10, 20, and $40mg{\cdot}L^{-1}$) and sucrose (0 and 2%, w/v). In pulsing solution treatment, cut roses were dipped into the FAC solutions of 100, 200, and $400mg{\cdot}L^{-1}$ for 10 seconds. The longest vase life of cut roses was observed in the holding solution with FAC $20mg{\cdot}L^{-1}$ as 12 days, followed by pulsing with $400mg{\cdot}L^{-1}$ as 11 days, which were four or five days longer than the control. In addition, relative fresh weight and water uptake were the highest in the holding solutions with FAC 20 and $40mg{\cdot}L^{-1}$. The antimicrobial effect of FAC in vase solution was lasted for eight days after treatment, which was offset by sucrose addition. FAC contents in the FAC holding solution mixed with sucrose were exhausted by 88% two days after treatment, whereas only 15% of FAC was reduced in the holding solution without sucrose. This study indicated that FAC can be applied to extension of the postharvest life of cut roses by antimicrobial activity.

• The Journal of the Korea Contents Association
• /
• v.9 no.9
• /
• pp.31-40
• /
• 2009

What are important in wireless sensor networks are reliable data transmission, energy efficiency of each node, and the maximization of network life through the distribution of load among the nodes. The present study proposed DSPR, a dynamic unique path routing machanism that considered these requirements in wireless sensor networks. In DSPR, data is transmitted through a dynamic unique path, which has the least cost calculated with the number of hops from each node to the sink, and the average remaining energy. At that time, each node monitors its transmission process and if a node detects route damage it changes the route dynamically, referring to the cost table, and by doing so, it enhances the reliability of the network and distributes energy consumption evenly among the nodes. In addition, when the network topology is changed, only the part related to the change is restructured dynamically instead of restructuring the entire network, and the life of the network is extended by inhibiting unnecessary energy consumption in each node as much as possible. In the results of our experiment, the proposed DSPR increased network life by minimizing energy consumption of the nodes and improved the reliability and energy efficiency of the network.

• Journal of Korean Society of Steel Construction
• /
• v.29 no.3
• /
• pp.193-204
• /
• 2017

Fatigue strength of temporary steels and painted structural steels corroded under outdoor atmospheric environments is not clear. In this study, fatigue tests were carried out on steel plates which were cut off from 7-year-old temporary structural member under subway construction environment and from 75-year-old Yeongdo bridge member under marine atmospheric environment. After removing corrosion production on the steel surface, 3-dimensional surface geometry of the corroded steel was measured at intervals of $1.0{\times}1.0mm$, and corrosion characteristics such as minimum, maximum and mean values of residual thicknesses were calculated. From the fatigue test and FEM analysis results, the relationship between corrosion characteristics and fatigue behavior was presented, and change in fatigue strength of the unpainted and painted steels corroded in outdoor environments was also presented.

• Journal of Convergence for Information Technology
• /
• v.9 no.12
• /
• pp.227-235
• /
• 2019

This study was conducted on 1,865 drunk elderly people who had teeth that were over 65 years old. As a result of analysis of factors related to tooth extraction, the higher the income, the lower the income, the higher the risk of having to remove teeth from smokers, poorer oral health status, and no oral hygiene products. The difference was statistically significant. In order to identify the risk factors of tooth extraction for the elderly and prevent tooth loss early and to extend the life of residual teeth as much as possible, it is necessary to improve the drinking culture and seek oral health care strategies in the previous life cycle, not the present, Oral health policy should be pursued.

• International Journal of Highway Engineering
• /
• v.2 no.1
• /
• pp.135-145
• /
• 2000

A new procedure needs to be developed to predict the dynamic layer properties under moving truck loads. In this study, a computer code to evaluate layer moduli of asphalt concrete pavement from measured interior deflections at various depths were developed and verified from numerical model tests. Interior deflections of the pavement are measured from Multi-Depth Deflectometer(MDD). It was found that errors between the given and backcalculated moduli in numerical analysis were less than 0.32% for several numerical models tested. When impact loads were used, a technique to determine the depth to virtual rigid base was proposed through the analysis of compressive wave velocity and impulse loading durations. It was found that errors between the given and backcalculated moduli in numerical analysis were less than 0.114% when virtual rigid base was considered in numerical analysis. The pavement behavior must be evaluated under various vehicle speeds when determining the dynamic interaction between the loading vehicle and pavement system. To evaluate the dynamic behavior on asphalt concrete pavement under various vehicle speeds, truck moving tests were carried out. From the test results with respect to vehicle speed, it was found that the vehicle speed had significant effect on actual response of the pavement system. The lower vehicle speed generates the higher interior deflections, and the lower dynamic modulus.

• Journal of the Korean Electrochemical Society
• /
• v.4 no.4
• /
• pp.152-159
• /
• 2001

Electric vehicle performance is very dependent on traction batteries. For developing the electric vehicles with high performance and good reliability, the traction batteries have to be managed to get maximum performance under various operating conditions. The enhancement of the battery performance can be accomplished by implementing battery management system (BMS) that plays important roles of optimizing the control mechanism of charge and discharge of the batteries as well as monitoring battery status. In this study the battery management system has been developed for maximizing the use of Ni/MH batteries in electric vehicle. This system provides several tasks: the control of charging and discharging, overcharge and over-discharge protection, the calculation and display of state of charge, safety and thermal management. The BMS was installed in and tested using the DEV5-5 electric vehicle developed by Daewoo Motor Co. and Institute for Advanced Engineering in Korea. The 18 modules of Panasonic Ni/MH battery, 12 V-95 Ah, were used in the DEV5-5. The high accuracy within the range of $3\%$ and the good reliability were shown in the test results. The BMS can also improve the performance and cycle life of Ni/MH battery pack as well as the reliability and safety of the electric vehicles (EV).

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.31 no.4
• /
• pp.463-470
• /
• 1998

To improve muscle quality and prolong freshness of sashimi, the effects of freezing-thawing condition on physicochemical and rheological properties of plaice muscle were investigated. Muscle tested were frozen with quick freezing (liquid nitrogen gas) or slow freezing ($-15^{\circ}C$ air). Transition time of zone of ice crystal formation was within 10 minute for quick freezing and 110 minute for slow freezing. Time required for thawing to $0^{\circ}C$ in muscle temperature by various thawing methods was shortest with $25^{\circ}C$ tap water, followed by $15^{\circ}C$ tap water, $10^{\circ}C$ tap water, $25^{\circ}C$ air, $5^{\circ}C$ tap water and $0^{\circ}C$ cold water. Breaking strength of muscle was higher in quickly frozen sample than in slowly frozen sample. According to sashimi term, changes in breaking strength of muscle did not show any difference in quickly frozen sample, while showed significant difference in slowly frozen sample. The remaining content of ATP was not effected by freezing speed, and ATP content was apt to higher in quickly thawed sample than in slowly thawed sample. IMP was the majority of ATP and it's related compounds of sample after freezing and thawing. Collagen matrix was weakened markedly in slowly frozen sample than in quickly frozen sample.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.4
• /
• pp.99-107
• /
• 2017

This paper proposes a battery model coefficient correction method for improving the accuracy of existing lithium battery equivalent models. BMS(battery management system) has been researched and developed to minimize shortening of battery life by keeping SOC(state of charge) and state of charge of lithium battery used in various industrial fields such as EV. However, the cell balancing operation based on the battery cell voltage can not follow the SOC change due to the internal resistance and the capacitor. Various battery equivalent models have been studied for estimation of battery SOC according to the internal resistance of the battery and capacitors. However, it is difficult to apply the same to all the batteries, and it tis difficult to estimate the battery state in the transient state. The existing battery electrical equivalent model study simulates charging and discharging dynamic characteristics of one kind of battery with error rate of 5~10% and it is not suitable to apply to actual battery having different electric characteristics. Therefore, this paper proposes a battery model coefficient correction algorithm that is suitable for real battery operating environments with different models and capacities, and can simulate dynamic characteristics with an error rate of less than 5%. To verify proposed battery model coefficient calibration method, a lithium battery of 3.7V rated voltage, 280 mAh, 1600 mAh capacity used, and a two stage RC tank model was used as an electrical equivalent model of a lithium battery. The battery charge/discharge test and model verification were performed using four C-rate of 0.25C, 0.5C, 0.75C, and 1C. The proposed battery model coefficient correction algorithm was applied to two battery models, The error rate of the discharge characteristics and the transient state characteristics is 2.13% at the maximum.

• Land and Housing Review
• /
• v.14 no.4
• /
• pp.1-16
• /
• 2023

As population ageing and shrinking accompanied by dramatically expanded individual life expectancy and declining fertility rate is a global phenomenon, ageing becomes its broader perspective of ageing well embedded into sustained health and well-being, and also the fourth industrial revolution speeds up a more robust and inclusive view of smart ageing. While the latest paradigm of SA has gained considerable attention in the midst of sharply surging demand for health and social services and rapidly declining labor force, the definition has been widely and constantly discussed. This research is to constitute a conceptual framework of smart ageing (SA) from systematic literature review and the use of a series of secondary data and Geographical Information Systems(GIS), and to explore its components. The findings indicate that SA is considered to be an innovative approach to ensuring quality of life and protecting dignity, and identifies its constituents. Indeed, the construct of SA elaborates the multidimensional nature of independent living, encompassing three spheres - Aging in Place (AP), Well Aging (WA), and Active Ageing (AA). AP aims at maintaining independence and autonomy, entails safety, comfort, familiarity and emotional attachment, and it values social supports and services. WA assures physical, psycho-social and economic domains of well-being, and it concerns subjective happiness. AA focuses on both social engagement and economic participation. Moreover, the three constructs of SA are underpinned by specific elements (right to housing, income adequacy, health security, social care, and civic engagement) which are interrelated and interconnected.