• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.05a
• /
• pp.265-269
• /
• 2005

본 논문에서는 최대 견인력 제어를 위해서 최소 차원 부하 토크 외란 관측기를 이용하여 점착력 계수를 추정하고 추정한 점착력 계수의 미분치를 PI 토크 제어하는 Anti-slip제어를 제안한다. 최소차원 부하 토크 외란 관측기는 회전자의 위치 정보와 토크 전류의 정보를 이용하여 부하 외란토크를 추정하고, 부하 외란 토크에 철도차량 상수를 이용하여 점착력 계수를 추정한다. 또한 부하토크외란 관측기는 구조가 간단하며, 시스템의 외란 및 각종 제어이득, 시스템의 상수 변화에 대해서도 견실한 견인력 제어 특성을 가지고 있다. 이와 같은 시스템의 모델링과 전동기 토크에 대한 회전자의 위치 정보를 이용하여 최소차원 부하 토크 외란 관측기의 상태변수인 점착력 계수를 추정하고, 추정한 점착력 계수의 미분치를 PI토크 Anti-Slip제어하여, 최대 견인력 제어가 되도록 하였다.

• Journal of Korean Society of Forest Science
• /
• v.108 no.4
• /
• pp.562-573
• /
• 2019

In a cable yarding system, a small-scale tower yarder attached to a farm tractor wasdeveloped and used for small-diameter tree harvesting operations. Based on this design, improvement of traction performance was required for medium- and large-diameter tree harvesting operations. In this study, the mechanical transmission employed for the tower yarder was modified into ahydro-mechanical transmission system. Maximum traction forces, including tractor engine speed and hydraulic power pressure, were investigated, and comparisons were made between the mechanical and hydro-mechanical transmission systems. Six tractor engine speeds (1,200, 1,400, 1,600, 1,800, 2,000, and 2,200) and three levels of power transmission mechanism pressure (4.9, 6.9, and 8.8 MPa) were investigated in the two different transmission systems. Results showed a maximum traction force of 15,146.6 N at an engine rotation speed of 757 rpm in the current mechanical transmission system, and 36,140.0 N at anengine rotation speed of 1,575 rpm in the modified hydro-mechanical transmission system. The maximum traction forces for the hydro-mechanical transmission were 2.4 times greater than those of the mechanical transmission, and may therefore be applicable to medium and large-diameter tree harvesting operations. Thus,as a modified version of the conventional transmission system, the new hydro-mechanical transmission system may be cost-effective for use in large-scale cable yarding operations. In the future, however, it will be necessary to investigate problems that may arise from field application tests.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2010.10a
• /
• pp.100-102
• /
• 2010

설계시와 다른 규모가 큰 선박이 접안을 할 경우라도 접안속도 및 적재화물 중량을 조절한다면 현재의 접안구조물 안전 및 전면수심에 문제는 없는 것으로 검토됨.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.2
• /
• pp.3-8
• /
• 2009

The traction system has been mainly used for rehabilitation and correction of patients with spine or gait diseases in orthopedics or at home. Some problems could occur in human body when patients forced their training using the traction system. So it needs to measure a traction force and control the training time. However, most of products on market have no sensor measuring traction force. Thus we designed and made a sensor detecting traction force using strain gauge, amplifier for transition to output signal and experiment devices for performance test. We carried out experiment of a sensor detecting a traction force and measured electric responses of it with respect to traction loads. Maximum error was within about 1% for experiments in static condition and the average error was about 0.7% for experiments in dynamic condition. We concluded that it is possible to use the developed sensor for measurement of traction force since the maximum output variation of a sensor detecting a traction force was about 0.3% in $0^{\circ}C-60^{\circ}C$ temperature condition.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7934-7940
• /
• 2015

The raise of the acceleration can be one of possible methods to increase the scheduled speed of the metropolitan railway system. It is possible to raise the acceleration to the some point by increasing the traction power of the motor. However, there is a limit of the acceleration because the traction power over some level related to the adhesion causes a slip, which prevents from accomplishing the target acceleration. The running resistance is also an important factor to consider. Both the adhesion and the running resistance as well as the traction power vary according to the velocity. Therefore, the standardization of the acceleration needs the analysis of these factors as a function of velocity. In this study, we focus on the advanced urban transit unit(AUTS) for the standardization. We derive a novel equation of the adhesion suitable for the AUTS by investigation of the traction and adhesion equation as well as the experiment data. And finally we propose the standard of the acceleration based on this analysis.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.4
• /
• pp.366-374
• /
• 2003

In electric motor coaches, the rolling stocks move by the adhesive effort between rail and driving wheel. Generally, the adhesive effort is defined by the function of both the weight of electric motor coach and the adhesive effort between rails and driving wheel. The characteristics of adhesive effort is strongly affected by the conditions between rails and driving wheel. When the adhesive effort decreases suddenly, the electric motor coach has slip phenomena. This paper proposes a re-adhesion control algorithm which uses the maximum adhesive effort by instantaneous estimation of adhesion force using load torque disturbance observer. Based on this estimated adhesive effort, the re-adhesion control Is peformed to obtain the maximum transfer of the tractive effort.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.80-80
• /
• 2017

국내에서 대부분 생산되는 사료(사일리지) 수확 작업은 베일 생산 및 비닐 래핑 작업이 독립적으로 수행되고 있어서 비효율적이다. 본 연구에서 개발한 조사료 수확기는 수집, 롤링, 베일 네트 생성, 래핑, 래핑 종료 및 베일 방출작업을 통합적으로 수행하도록 설계-제작하였다. 통합형 다목적 조사료수확기의 설계는 3D 디자인 툴 (CATIA V5R18)을 이용하여 실시하였으며, 기구부 23 파트 어셈블리, 전기제어 어셈블리, 유압요소기술을 통합하여 통합시작기를 제작하였다. 기초 프레임, 오거장치파트, 픽업장치파트, 하부롤러파트, 상부롤러파트, 하부 프레임 및 주행부 파트, 래핑회전파트, 롤러부 구동 동력부, 유압파트, 전기제어파트, 드로우바파트, 체결 및 컨트롤러 파트 등 25개 파트로 구성되어 있다. 본 연구에서 개발한 시작기의 견인력 및 소요동력 분석은 선행 연구에서 사용한 Brixius (1987) 제안 모델을 체택하여 분석하였다. 이 Brixius 제안 모델은 견인력 예측에서 토양변수 및 토양강도 특성을 나타내는 원추지수 (Cone Index, CI)를 이용하여 트랙터의 견인력 예측에 사용하였다. 또한 트랙터-조사료수확기 시스템의 소요 견인력을 예측하는데 있어, 트랙터-조사료수확기 시스템이 운용되는 토양조건과 트랙터의 마력에 따른 소요 견인력 특성을 분석하기 위해 대표적으로 3수준의 토양조건 (CI: 356 kPa, 543 kPa, 1,429 kPa)을 적용하였으며, 베일의 개당 최대무게는 최고 수준인 옥수수 기준으로 800 kgf를 적용하였다. 본 연구에서 적용된 3수준의 CI 조건은 연구팀에서 선행연구과정 (토양특성에 따른 최적 경운작업 시스템 개발, 2006)에서 분석한 전국 10개 지역의 33개 지점의 경반층 CI지수의 측정범위인 1,050-3,170 kPa에 대해 견인력이 많이 소요되는 열악한 조건 수준을 적용하였다. 각 작업에 사용된 소요동력은 베일 작업시 (ASABE D497.7, 2011) 그리고 래핑작업시 (Zhortuylov et al., 2013)를 사용하였으며 두 소요마력을 트랙터-조사료 수확기 시스템의 필요 소요마력의 합계로 계산하였다. 트랙터-조사료수확기 시스템의 최소 소요 동력, 차축 소요 동력과 PTO 소요 동력을 Zoz and Grisso (2003)을 이용하여 계산하였다. 연구에서는 기본적으로 ASAE의 작업속도 및 작업효율을 적용하였는데, 적용된 조사료수확기의 현장 작업효율은 60-86%의 범위이고 일반적으로 70%를 적용하고 이때 작업속도는 2.5-8.0 km/h이며 전형적으로 5.0 km/h를 기준하고 있다. 자주식 (SP; sief-propelled machine) 조사료수확기의 경우 작업속도가 2.5-10.0 km/h의 범위에서 작업효율은 60-85% 범위이다. 적용되는 조사료 수확기의 작업효율인 60-85% 범위에서 일반적으로 적용되는 작업효율인 70%를 적용하면 트랙터의 소요동력은 95hp를 적정 작업환경으로 하였다.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.2
• /
• pp.171-181
• /
• 2009

The objective of this study was to analyse stress distribution of maxillary complex by use of face mask. The construction of the three-dimensional FEM model was based on the computed tomography(CT) scans of 13.5 years-old male subject. The CT image were digitized and converted to the finite element model by using the mimics program, with PATRAN. An anteriorly directed force of 500g was applied at the first premolar 45 degrees downwards to the FH plane and at the first molar 20 degrees downwards to the FH plane. When 45 degrees force was applied at maxillary first premolar, there were observed expansion at molar part and constriction at premolar part. The largest displacement was 0.00011mm in the x-axis. In the y-axis, anterior displacement observed generally 0.00030mm at maximum. In the z-axis, maxillary complex was displaced 0.00036 mm forward and downward. When 20 degrees force was applied at maxilla first molar, there were observed expansion at lateral nasal wall and constriction at molar part. The largest displacement was 0.001mm in the X-axis. In the Y-axis, anterior displacement observed generally 0.004mm at maximum. In the Z-axis, ANS was displaced upward and pterygoid complex was displaced downward. The largest displacement was 0.002mm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.3
• /
• pp.265-270
• /
• 2006

When the dynamic crack propagates along the boundary at the strip with composite materials and tears apart it, the equivalent stress and strain, and the traction stress are investigated near its boundary. There are the maximum equivalent stress and plastic strain at the very seperated part and the maximum displacement at the bent part of the end of strip. The traction stress becomes higher as the separation distance becomes more. Its maximum value becomes 75 MPa as this distance becomes 0.015 mm. As this distance becomes more than 0.015 mm, this stress becomes lower. As this distance becomes more than 0.13 mm, the value of this stress becomes 0 constantly. This study aims at doing the basic study to provide the data necessary for the precise analysis of fracture intensity, the safety design and the development of advanced materials.

• The korean journal of orthodontics
• /
• v.38 no.5
• /
• pp.304-313
• /
• 2008

Objective: The purpose of this study was to evaluate the stress distribution in bone and displacement distribution of the miniscrew according to the length and number of the miniscrews used for the fixation of miniplate, and the direction of orthodontic force. Methods: Four types of finite element models were designed to show various lengths (6 mm, 4 mm) and number (3, 2) of 2 mm diameter miniscrew used for the fixation of six holes for a curvilinear miniplate. A traction force of 4 N was applied at $0^{\circ}$, $30^{\circ}$, $60^{\circ}$ and $90^{\circ}$ to an imaginary axis connecting the two most distal unfixed holes of the miniplate. Results: The smaller the number of the miniscrew and the shorter the length of the miniscrew, the more the maximum von Mises stress in the bone and maximum displacement of the miniscrew increased. Most von Mises stress in the bone was absorbed in the cortical portion rather than in the cancellous portion. The more the angle of the applied force to the imaginary axis increased, the more the maximum von Mises stress in the bone and maximum displacement of the miniscrew increased. The maximum von Mises stress in the bone and maximum displacement of the miniscrew were measured around the most distal screw-fixed area. Condusions: The results suggest that the miniplate system should be positioned in the rigid cortical bone with 3 miniscrews of 2 mm diameter and 6 mm length, and its imaginary axis placed as parallel as possible to the direction of orthodontic force to obtain good primary stability.