• Korean Journal of Optics and Photonics
• /
• v.20 no.4
• /
• pp.207-210
• /
• 2009

A confocal technique was demonstrated for measuring the absolute value of an air gap between substrates. Since the two surfaces were in Rayleigh range of the laser focus for air gaps less than 200 nm, complete interference patterns were observed. And since interference patterns were obtained only from the area of focus, it was an advantage of this method that air gaps between multiple thin films could be measured. Stability is less than 1 nm except in the range where the interference pattern changes slowly.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.30.1-30.1
• /
• 2005

• Korean Journal of Optics and Photonics
• /
• v.33 no.4
• /
• pp.146-158
• /
• 2022

The detector of a focal-plane-array mid-wave infrared (MWIR) camera has different response characteristics for each detector pixel, resulting in nonuniformity between detector pixels. In addition, image nonuniformity occurs due to heat generation inside the camera during operation. To solve this problem, in the process of camera manufacturing it is common to use a gain-and-offset table generated from a blackbody to correct the difference between detector pixels. One method of correcting nonuniformity due to internal heat generation during the operation of the camera generates a new offset value based on input frame images. This paper proposes a technique for dividing an input image into block image patches and generating offset values using only homogeneous patches, to correct the nonuniformity that occurs during camera operation. The proposed technique may not only generate a nonuniformity-correction offset that can prevent motion marks due to camera-gaze movement of the acquired image, but may also improve nonuniformity-correction performance with a small number of input images. Experimental results show that distortion such as flow marks does not occur, and good correction performance can be confirmed even with half the number of input images or fewer, compared to the traditional method.

• The Journal of Engineering Geology
• /
• v.11 no.2
• /
• pp.205-214
• /
• 2001

A simple automated measuring method for planar or linear features on the rock excavation surface is presented. Attitude of the planar and linear feature is calculated from 3D coordinates of points on the structures. Spatial coordinates are calculated from overlapped stereo images. Factors used in the calculation are (1) local coordinates of the left and right images, (2) the focal length of cameras, and (3) the distance between two cameras. A simple image capturing device and an image treatment routine coded by Visual Basic and GIS components are constructed for the remote measurements, The methodology shows less than 1 cm error when a point is measured from 179 cm in distance. The methodology is tested at the excavation site in PaiChai University. Remotely measured result matches well with the manual measurement within the reasonable error range.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.387-390
• /
• 1999

누설탄성표면파(Leaky Surface Acoustic Wave : LSAW) 측정에 사용하는 것을 목적으로 PVBF 압전막을 이용하여 직선집속 초음파트랜스듀서를 제작하고 그 특성을 평가하였다. 제작은 한쪽 면이 원통형 구조를 갖는 구리, 알루미늄, 3mmPVC-에폭시 3가지 재료를 배면층으로 사용하여 각각에 PVDF를 부착시켜서 수중에 음파를 방사하도록 구성하였고, 특성평가는 임펄스응답 특성과 음장 특성으로 나누어서 평가하였다. 임펄스응답 특성은 제작한 3종류의 집속 초음파트랜스듀서에 대해 실험적으로 측정하고, Mason 등가회로1)를 이용한 이론적 해석결과와 비교하였다. 음장특성 측정실험은 구리를 배면체로 하여 제작한 집속 초음파트랜스듀서에 대해서 실시하였고, 그 이론적인 계산결과는 Raylelgh-Somme-rfeld 회 절이론2)을 도입하여 초점면에 형성되는 음압분포를 계산하는 것으로 얻어졌다. 실험은 펄스 초음파 송수기 및 $2{\mu}m/step$으로 이동하는 정밀 x-y-z 스테이지를 컴퓨터에 연결하여 자동 측정하는 것으로 수행되었는데, 그 결과는 이론 해석결과와 비교적 잘 일치하였다.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.1
• /
• pp.62-67
• /
• 2001

Velocities of leaky surface acoustic waves (LSAW/sub s/) were measured by using a line-focus polyvinylidene fluoride (PVDF) transducer and compared with theoretically calculated ones. Isotropic materials of Cu, Al, fused quartz, and anisotropic one of Z-cut α-quartz crystal were used as specimens. The velocities were obtained by the separation time between wave components reflected directly from the surface of specimen and LSAW components according to the defocusing distance. The measured velocities well agree with the theoretical results within 1％ error, and it was shown that the leaky pseudo-surface acoustic wave (LPSAW) as well as the LSAW propagates with the typical 6-fold anisotropy on the (0,0,1) surface of α-quartz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.6
• /
• pp.1493-1498
• /
• 2015

The autofocus system is automatically to drive the focus. It is very important to computer vision system. In the case of a compact camera, the actuator technology is used for auto-focus in mass production. the position sensor is required, the circuit configuration and easy method is widely used in VCM, compared to the stability of the drive size and the noise is a big stepping motor type, size has a piezo system having a humidity problem and the small leaded vulnerability. In addition, there is a liquid lens system, the advantages of low power in a compact structure but also a structure with proven quality and reliability and features required pressure. In this paper, we implement two control systems that can control the actuator as a liquid range of VCM using a sharpness of the image acquired by the image sensor automatically initiates 5Mpixel class was the implementation verification of focusing.

• Journal of the Korea Convergence Society
• /
• v.9 no.9
• /
• pp.183-189
• /
• 2018

This study deals with the design and development of imaging optics having 24mm focal length for MWIR ($3{\sim}5{\mu}m$) with two symmetrical lenses facing each other. We used CodeV in our optical design, and we performed the optimization process to have the resolution and angle of view satisfying the user's requirements. The materials of lenses were limited to two types, including KCIR035 with a refractive index of 1.7589, developed in Korea. The optical system designed in this way consists of two aspherical lenses made of KCIR035 material having the same shape and one spherical lens made of Si. Here, the arrangement of the two aspherical lenses is characterized by having a symmetrical structure facing each other. And this optical system has a resolution of MTF value of 0.35 or more at a line width of 20 lp / mm. Therefore, it is considered that this optical system has the capability to be applied to a thermal imaging camera using a $206{\times}156$ array MWIR detection device having a pixel size of $25{\mu}m$.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.1
• /
• pp.73.3-74
• /
• 2016

본 연구에서는 비구면 반사경의 형상오차를 3가지 방법으로 측정, 비교하였다. 실험에 사용한 포물면 반사경의 구경은 108 mm, 유효초점거리는 444.5 mm 이다. 첫 번째로 접촉식 형상측정방식인 FTS(Form TalySurf)를 이용하여 표면 거칠기와 반사경의 최적 곡률 반경(BestFitt Radius) 값을 측정하였다. 두 번째로는 비접촉식 형상측정방식인 UA3P(Ultrahigh Accurate 3-D Profilometer)를 이용하여 반사경의 형상 정밀도를 측정하였다. UA3P를 이용할 경우 반사경의 전체 형상을 측정할 수 있다. 세번째로 Shark-Hartmann 센서를 이용한 광학측정방법으로 반사경의 형상 정밀도를 측정하였다. 측정에 필요한 레이저 광학계는 레이저, 콜리메이터, 핀홀, 카메라 렌즈 및 비구면 광학계를 이용하여 설계하였다. 본 연구에서 도출한 각 측정 방법의 신뢰도를 바탕으로 간섭계 사용에 제약이 있는 자유형상곡면의 반사경 표면의 형상오차 측정에 적용할 계획이다.

• Electronics and Telecommunications Trends
• /
• v.22 no.6
• /
• pp.158-169
• /
• 2007

지금까지 인터넷 망의 공개성과 중립성이 콘텐츠와 응용 서비스의 활력과 발전을 가져온 것이 사실이지만, 기술적 측면에서 보면 차별화의 행위 중에는 유익한 면과 시장에 해가 되는 양면성을 지니고 있다. 망중립성 규제의 내용과 범위에 따라 이해관계자의 대응방향을 모의상황을 통해 추정해보고, 정책의 방향을 모색해보는 것은 중요한 의미를 가진다. 모의상황 설정에서 초점을 둔 것은 규제정책의 범위에 따른 상호 거래관계, 혁신기회, 거래비용, 도입비용 등의 동태이다. 결론은 기술의 빠른 발전에 의한 미래의 불확실성이 완벽한 망중립성을 주장하는 것을 어렵게 한다. 한편, 차별화(discrimination)와 차등화(differentiation)의 경제적 의미는 다르지만, 망중립성 규제의 옹호론자들은 두 가지 모두 차별화의 범주에 넣어 규제하려 한다. 이러한 시각의 차이는 논쟁을 핵심으로부터 벗어나게 하는 원인이 되고 있다. 망사업자의 차별화를 제한함에 있어 정책의 올바른 방향은 차별화의 행위가 갖는 유용한 면과 위해한 면의 균형을 이루는 것이 핵심 과제이다.