• Progress in Superconductivity
• /
• v.10 no.2
• /
• pp.116-122
• /
• 2009

We introduce a measurement method that enables to measure the penetration depth($\lambda$) of superconductor films by using a short-ended parallel plate sapphire resonator. Variations in the $\lambda$ of $MgB_2$ films could be measured down to the lowest temperature using a sapphire resonator with a $YBa_2Cu_3O_{7-x}$ film at the bottom. A model equation of $\lambda=\lambda_0[1-(T/T_c)^{\tau}]^{-1/2}$ for $MgB_2$ films appeared to describe the observed variations of the resonant frequency of the sapphire resonator with temperature, with $\lambda_0,\;\tau$, and $T_C$ used as the fitting parameters.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1218-1221
• /
• 2004

Bi2212 superconducting thin films fabricated by using the ion Beam Sputtering Method. As a result, although the composition of Bi2212 was set up, the phase of Bi2201, Bi2212 and Bi2223 was formed. The formation area of these stable phases is indicated as inclined line in the direction of the right lower end from the Arrhenius plot of the substrate temperature-oxidation gas pressure, and are distributed in very small area. The activation energy for the phase transformation from the Bi2201 to the Bi2212 is estimated in terms of the Avrami equation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.278-280
• /
• 2001

BSCCO thin films have been fabricated by co-deposition at an ultralow growth rate using ion beam sputtering(IBS) method. The growth rates of the films was set in the region from 0.17 to 0.27 nm/min. MgO(100) was used as a substrate. In order to appreciate stable existing region of Bi 2212 phase with temperature and ozone pressure, the substrate temperature was varied between 655 and $820^{\circ}C$ and the highly condensed ozone gas pressure($PO_3$) in vacuum chamber was varied between $2.0{\times}10^{-6}$ and $2.3{\times}10^{-5}$ Torr. Bi 2212 phase appeared in the temperature range of 750 and $795^{\circ}C$ and single phase of Bi 2201 existed in the lower region than $785^{\circ}C$. Whereas, $PO_3$ dependance on structural formation was scarcely observed regardless of the pressure variation. And high quality of c-axis oriented Bi 2212 thin film with $T_c$(onset) of about 90 K and $T_c$(zero) of about 45 K is obtained. Only a small amount of CuO in some films was observed as impurity, and no impurity phase such as $CaCuO_2$ was observed in all of the obtained films.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.68-71
• /
• 2003

We fabricated Ni-substrate for YBCO coated conductors and evaluated the effects of pressing and annealing time on texture. Ni substrate was fabricated by powder metallurgy technique and compacts were prepared by applying uniaxial or isostatic pressure. The texture of substrate made by applying cold isostatic pressure (CIP) was stronger than that by uniaxial pressure. The texture of substrate made by CIP had a strong 4-fold symmetry and [111] ∥ ND texture after annealing temperature of 100$0^{\circ}C$. It is to be noted that the degree of texture was almost independent of annealing time and the full-width at half-maximum (FWHM) of in-plane and out-of-plane was measured to be in the range of 9.55$^{\circ}$-10.53$^{\circ}$ and 8.57$^{\circ}$-9.85$^{\circ}$, respectively. Development of strong cube texture of Ni-substrate made by powder metallurgy technique in our study is considered to be suitable for the application of YBCO coated conductors.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.117-119
• /
• 2003

YBa$_2$Cu$_3$O$_{7-{\delta}}$(YBCO) high temperature superconducting thin films were grown on SrTiO$_3$single crystal substrates by pulsed laser deposition(PLD). The texture and lattice parameter of the YBCO films were analysed using the GADDS (general area detector diffraction system) which enables XRD analyses to be done faster and with fewer sample movement than with the XRD system with point detector. The XRD results of the films grown in different deposition conditions are reported together with the SEM microstructure analysis results.ysis results.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.109-112
• /
• 2003

The high temperature superconducting YBCO films were deposited on the SrTiO$_3$(100) single crystals to find out the proper deposition conditions of YBCO on biaxially-textured metal substrates. Different sets of the substrate temperature, oxygen partial pressure and laser fluence were used to investigate the effect of deposition conditions on the superconducting properties. The new apparatuses for measuring critical temperature (Tc) and critical current (Ic) were designed and manufactured, which were used to obtain Tc's and Ic's of the deposited films. The accuracy of the new apparatus was confirmed by comparing the results with those from SQUID magnetometer. The results on the YBCO films deposited on single crystal substrates which will be used to get the optimum deposition conditions of YBCO films in the coated conductor, are summarized in this report.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.711-712
• /
• 2006

For the application of superconducting fault current limiters(SFCLs) to the protection system, quench recovery characteristics of Au/YBCO thin film were investigated. The Au/YBCO thin film was designed as a SFCL element with a bi-spiral pattern. The SFCL element limited the fault current successfully. For the analysis of the recovery to superconducting state, we measured resistance variation of the SFCL element after the quench. In addition, in order to investigate the dependence of quench characteristics of SFCL on the $LN_2$ cooling condition, we measured the recovery time under a pressure of 1, 2 and 3 atm. As the results, the recovery time increased in proportion to the duration of the fault currents. In the sub-cooled condition, while the quench development was exactly the same, the recovery time was shortened as the pressure increased.

• Proceedings of the KIEE Conference
• /
• 2003.07a
• /
• pp.415-417
• /
• 2003

we analyzed the electromagnetic behavior of a superconducting fault current limiter (SFCL) under the quench state using FEM. The analysis model used in this work is 5.5 KVA meander-line type SFCLs. Meshes of 3,650 triangular elements were used in the analysis of this SFCL. Analysis results showed that the distribution of current density was concentrated to inner curved line in meander-line type-SFCL and the maximum current density was 14.61 $A/m^2$ and also the maximum Joule heat was 2,030 $W/m^2$ in this region. We think that the new and the modified structure must be considered for an uniform distribution of the electromagnetic field.

• Electrical & Electronic Materials
• /
• v.7 no.4
• /
• pp.289-293
• /
• 1994

Thin films of YB $a_{2}$C $u_{3}$$O_{7-x}$ supercondYB $a_{2}$C $u_{3}$$O_{7-x}$uctor were prepared on (100) SrTi $O_{3}$ substrates by pulsed laser deposition using visible light laser. Q-switched Nd:YAG(532 nm, 30 ns) pulsed laser was used for deposition. The effects of substrate temperature and oxygen pressure during deposition on films were studied. Critical current density of 2.93*10$^{6}$ A/c $m^{2}$ at 77K and Tc(zero)=91.7K were obtained from the film prepared with Tsub=745.deg. C and $P_{02}$=200 mTorr. XRD analysis showed that the grown film has c-axis normal orientation to the substrate surface and has single phase. Surface morphology of the film has been improved by interfering the plume ejected from YB $a_{2}$C $u_{3}$$O_{7-x}$ target.arget.t.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.337-339
• /
• 1998

This paper deals with the design and fabrication of a novel superconducting power supply system, and characteristics have been analyzed through experiments. Superconducting power supply consists of rotating and static parts, and superconducting magnet. In this experiment, the current-pumping characteristics have been analyzed with superconducting sheets placed in parallel within the static part of the machine. In addition, in order to observe the 3-dimensional flux distribution in the superconducting sheet, several hall-sensors were placed in it. With the flux distribution acquired, the effect of the flux on the superconducting sheet during the process of current pumping have been analyzed. Also, general operational characteristics of the superconducting power supply system have been investigated on the basis of the current and voltage data and magnetic field values acquired through the experiments. In this experiment, maximum pumping current has been achieved to about 1280 amps.