• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.515-519
• /
• 2002

자동차 및 유체기계의 흡기계나 배기계에 사용되는 소음기의 음향성능은 전달손실로 기계성능은 배압으로 표현된다. 유체가 흐르는 관 사이의 임피던스 부정합을 이용하는 반사형 소음기의 경우, 내부 유로에 천공을 주어 음향감쇠를 시키거나 유동을 안정시키는 경우가 많다. 본 연구에서는 동심관형 공명기의 내부 관에 존재하는 천공의 분포 양상이 소음기의 전달손실과 배압에 미치는 영향을 실험을 통하여 고찰하였다. 내부관의 평균 천공율은 일정하지만 길이 방향을 따라서 천공율이 변하는 다섯가지의 공명기에 대한 실험을 수행하고, 성능에 미치는 영향을 살펴보았다. 전달손실은 천공요소의 임피던스 모델을 고려하여 예측한 결과와 비교하였고, 측정된 배압은 모의 해석 결과와 비교하였다. 분석 결과, 천공율이 점점 작아지는 분포나, 작았다가 커진후 다시 작아지는 형태의 분포를 가질 경우, 배압 측면에서 매우 유리하고, 음향 전달손실도 큰 차이가 없음을 밝혔다.

• The Journal of the Acoustical Society of Korea
• /
• v.36 no.5
• /
• pp.305-313
• /
• 2017

In this paper, sound absorption of thin elastic plates installed in a rigid duct is discussed using an analytic method. The number of plates can be one or two, and each plate might have micro-perforation. Vibration of the plates and sound pressure fields inside the duct and air cavity are expressed in terms of an infinite series of modal functions. Under the plane wave assumption, a low frequency approximation is derived by including the first few plate modes. It is found that the sound absorption coefficient of the plates without micro-perforation shows sharp peaks at resonance frequencies, and due to the interaction between the plates and air cavity, the resonance frequencies move as the cavity depth changes. For the case of micro-perforated plates, it is found that the sound absorption is mainly affected by the perforation ratio. When the perforation ratio is order of few percent, the sound absorption is almost independent of plate vibration.

• Explosives and Blasting
• /
• v.34 no.2
• /
• pp.10-17
• /
• 2016

Drilling operation for blasting is an important factor to determine blast effect. Drilling errors that arise from performing drilling for blasting purposes can reduce blasting effect causing residual holes, overbreak, and heterogeneous fragmentation, etc. Automatic drilling system was induced for precise drilling. As a result, drilling error caused by spaces between holes and burden was minor at 0~2.6% and accordingly, blasting effect was improved with over 90% drilling rate, the ratio of overbreak amount to total drilling amount at 4.3%, proportion of fragmentation rock under 50cm at 89~95% and so from this analyses, it was estimated to reduce the total cycle times related to blasting process.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.4
• /
• pp.181-187
• /
• 2018

In this paper, sound absorption of micro-perforated elastic plates installed in an impedance tube of a circular cross-section is discussed using an analytic method. Vibration of the plates and sound pressure fields inside the duct are expressed in terms of an infinite series of modal functions, where modal functions in the radial direction is given in terms of the Bessel functions. Under the plane wave assumption, a low frequency approximation is derived by including the first few plate modes, and the sound absorption coefficient is given in terms of an equivalent impedance of a single surface. The sound absorption coefficient using the proposed formula is in excellent agreement with the result by the FEM (Finite Element Method), and shows dips and peaks at the natural frequencies of the plate. When the perforation ratio is very small, the sound absorption coefficient is dominated by the vibration effect. However, when the perforation ratio reaches a certain value, the sound absorption is mainly governed by the rigid MPP (Micro-Perforated Plate), while the vibration effect becomes very small.

• The Korean Journal of Malacology
• /
• v.27 no.2
• /
• pp.131-141
• /
• 2011

Boring caracteristics, boring rate, and predation, rates on the valves of the seed and adult clams of Meretrix petechialis by Glossaulax didyma didyma in the shellfish aquafarm and the indoor rearing aquarium were investigated by various morphometric data. The investigations were carried out from June to September, 2007. The morphology of drilled holes on the valves of M. petechialis showed the crater type as seen in the spats of Ruditapes philippinarum and M. lusoria. The sizes of the outer diameters of holes were greater than the inner diameters of the holes on the valves of M. petechialis in the shellfish aquafarm and the indoor aquarium at the laboratory. On the whole, the sizes of the holes on the valves of the seeds of M. petechialis was smaller than those bored holes on the adult valves. The location of the bored holes on the valves of the seeds varied widely with the the sizes of the individuals of M. petichialis, while most of holes on the valves of adult clams were located near the umbo position of the valves of the clams in the shellfish aquafarm and the indoor aquarium at the laboratory. On the whole, the outer and inner diameters of the bored holes increased with increase of shell lengths of the clams in the shellfish aquafarm and the indoor rearing aquarium at the laboratory. The authors could confirm experimentally the boring snail, G. didyma didyma, drilled the seeds and adult clams of M. petechialis. In the experiments for 15 days (three times repeated) in the indoor rearing aquarium at the laboratory, the mortality of dead shells to total shells of M. petechialis by boring snail Glossaulax didyma didyma was totally average 41.5%, and percent of drilled shells to total dead shells of clams by the boring snail was average 47.1%. Of total shells, percent of drilled shells to total shells of clams by the boring snail was totally average 19.3%. Predation of G. didyma didyma were greater at night than the day time. Average 0.5 seed and adult individuals of M. petewchialis were consumed per G. didyma didyma, per day. Predation varied with shell lengths of M. petechialis and shell widths of G. didyma didyma.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.4
• /
• pp.165-171
• /
• 2014

The rate of the channel code can be controlled by various methods. Puncturing is one of the methods of increasing the code rate, and the original code before puncturing is called the mother code. Any (n,k) convolutional code is obtainable by puncturing some mother codes, and the process of finding the mother code is necessary for designing the optimum channel decoder. In this paper, we proved that any (n,n-1) convolutional code has (2,1) mother codes regardless of the puncturing pattern and showed that they must be equivalent.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.2 no.1
• /
• pp.63-70
• /
• 1969

1. This paper deals with the natural mortality of the early young bivalve, Meretrix lusoria, (less than 13mm in shell length) and the perforations bored in the bivalve by bering snails, Neverita didyma and Natica severa. The investigation was carried out in the Kunsan area and in the laboratory from May to October of 1968. 2. The natural mortality of the field population during this period was $12.1\%$ and among this number $38.1\%$ were drilled by boring snails. 3. The common species of the Naticid gastropods, boring snails-Neverite didyma and Natice severa - are encountered in the habitat of M. lusoria. The perforations drilled by these species were broadly bevelled. 4. The location of the holes on the valves varied widely, while most of holes on the valves were located at a relatively definite umbo position. 5. The inner and outer diameters of the holes varied in proportion to the shell length of the clam; each ranging in shell length from 1 to 3mm, 3 to 6mm, and 6 to 13mm, and the outer diameters were 0.4-0.5mm, 0.7-0.9mm and 0.9-1.2mm. On the other hand, the ratio of the inner and outer diameters differed in proportion to the shell length of the clam. 6. Predation rates of Neverita didyma was much greater at night than during the day at room temperature. An average of 1.7 young clams was drilled and consumed, per snail, per day. This rate was greater than that of the Natica severa. 7 Predation rates varied in proportion to the shell length of the clam and the shell height of the snails.

• Journal of the Korean housing association
• /
• v.22 no.1
• /
• pp.105-114
• /
• 2011

There are various kinds of Large-Scale apartment sites in Seoul. There are more households in apartment sites than single family houses. Nowadays, it is easy to find a lot of apartment sites built in the style of a high rise building. On the matter of space, a building is influenced by the buildings near it. The influence a building has to another is different in both qualitative and quantitative ways. Therefore, in the case of apartment sites, the environmental surroundings of each household is affected by the nearby buildings. For these reasons, the environment is having more and more influence on the price of each household in apartment sites. This paper has defined Sunshine and Sky as the major environmental elements. In order to be analyzed, they have to be measurable. Thus, there are two types of variables in environmental surrounding of apartment sites, -the Duration of Sunshine and the possible amount of visible Sky- the significant variables which influence the housing price. This paper deals with the relationship between the possible duration of sunshine and the possible amount of sky a household is visible to. It focused on 62 different apartment sites which were built after 1990. It is based on the 3-dimensional Geographic Information System & Computer Aided Engineering for analyzing the sunshine simulation and the viewing simulation. This paper will be helpful for designing the apartment sites considering the balance between sunshine and sky.

• Journal of agriculture & life science
• /
• v.50 no.5
• /
• pp.217-224
• /
• 2016

In this study, performance of a developed automatic punching machine considering the planting density of soybeans was evaluated in the case of the operation speed of 0.18-0.28 m/s. The performance demonstrated a rate of 320-500 ㎡/h, 260-400 ㎡/h, and 210-330 ㎡/h for the 0.20 m, 0.25 m, and 0.30 m soybean planting density, respectively. One hundred percent punching capacity was confirmed in 30 mm distance between the ground and the blade. Additionally, in the 50 mm distance condition, the performance of round, square, and hexagonal blades were observed in the range of 16.7-25.2%, 33.0-42.3%, and 54.5-100.0%, respectively. Above all, the hexagonal blade with a 60° edge angle had the most superior cutting quality demonstrating a smooth and soft cutting plane of the plastic.

• Journal of Ecology and Environment
• /
• v.29 no.3
• /
• pp.185-189
• /
• 2006

Optimum tapping size and number for sap collection were investigated to minimize damage on tree growth and secure resources for sap by sap collection of Acer mono. The amounts of sap collected by tapping size of 12 mm, 10 mm and 8 mm was 189 L, 140 L and 193 L, respectively. Fusion rates by tapping size were 100% for 8 mm, 89% for 10 mm and 85% for 12 mm, respectively. Amount of sap by size and number of tapping were much at three, two and three tappings to small, middle and large diameter tree in case of 8 mm tapping, and it was large in quantity at two tappings of 12 mm tapping to large diameter tree, respectively. Trees tapped from one to three tappings of 8 mm size for small diameter tree with treatment of DB ointment (mixture of thiophane ointment and 2% bamboo charcoal powder) were completely filled up within 6 months. Diameter growth by number of tapping of 8 mm size was 0.60 mm for one tapping, 1.12 mm for two tappings and 0.47 mm for three tappings to small, middle and large diameter tree, respectively. In case of 12 mm tapping size, diameter growth was fast in the order of large (0.55 mm), middle (0.30 mm) and small (0.23 mm) diameter tree, respectively.