• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.1
• /
• pp.21-32
• /
• 2002

In general, the response spectrum analysis method (R.S.A) is widely used for seismic analysis of building structure. But, it is not common to apply R.S.A for the analysis of structural vibration caused by dynamic loads of equipments, machines and moving leads, etc. The time history analysis method(T.H.A) for the vibration analysis, compared with R.S.A, is very complex, difficult and time consuming. So the application of R.S.A, that is convenient to calculate maximum responses for structural vibration, is proposed in this study. At first, the procedure for the application of the R.S.A to calculate of the maximum vibration response induced by dynamic load applied on the single point is described. And then, the process, which can save the time and the memory for calculation of the maximum vibration response induced by dynamic loads on the multi-point is proposed, and the maximum structural response caused by moving loads are obtained. Lastly, the accuracy of the proposed method is verified by comparing the results of R.S.A to T.H.A for some example models.

• Tunnel and Underground Space
• /
• v.19 no.6
• /
• pp.490-497
• /
• 2009

The horizontal and vertical response spectra using the observed ground motion from the recent 5 macro earthquakes were analysed and then were compared to both the seismic design response spectra(Reg Guide 1.60), applied to the domestic nuclear power plants, and the Korean Standard Design Response Spectrum for general structures and buildings(1997). 74 horizontal and 89 vertical observed ground motions, without considering soil types, were used for normalization with respect to the peak acceleration value of each ground motion. The results showed that the horizontal MPOSD(Mean Plus One Sigma Standard Deviation) response spectra revealed much higher values for the whole frequency bands above 1 Hz than Reg. Guide(1.60). For the vertical response spectra, the results showed slightly higher than just between 7 and 8 Hz frequency band. The results were also compared to the Korean Standard Response Spectrum for the 3 different soil types and showed that the horizontal MPOSD response spectra revealed much higher values for the whole periods below 2 second(0.5 Hz) than those of SE soil type. The vertical response spectra showed similar to the values of the Korean Standard Response Spectrum of SD soil type. These spectral values dependent on frequency could be related to characteristics of the domestic crustal attenuation and the effect of each site amplification. However, through the qualitative improvements and quantitative enhancement of the observed ground motions, the conservation of horizontal seismic design response spectrum should be considered more significantly for the whole frequency bands above the 1 Hz.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2A
• /
• pp.273-284
• /
• 2006

In this study, After considering the general characteristic of Near Fault Ground Motion, the inelastic response spectrum is made to evaluate using the change of ductility and yield stiffness coefficient according to the inelastic behavior of structures which couldn't be examined through the elastic response spectrum. It is conducted to the elastic and inelastic time history analysis about the long period structure which could reflect the characteristic of Near Fault Ground Motion with the best and it is also examined the aspect of response distribution about the input data. Moreover, the response characteristic of structure is analyzed by investigating the plastic hinge for the purpose of grasp about the inelastic behavior of structure.

• Geophysics and Geophysical Exploration
• /
• v.13 no.3
• /
• pp.227-234
• /
• 2010

The vertical response spectra using the observed ground motions from the recent more than 30 macro earthquakes were analysed and then were compared both to the seismic design response spectra (Reg Guide 1.60), applied to the domestic nuclear power plants, and to the Korean Standard Design Response Spectrum for general structures and buildings (1997). 176 vertical ground motions, without considering soil types, were used for normalization with respect to the peak acceleration value of each ground motion. The results showed that response spectrum had strong dependency on epicentral distance. The results also showed that the vertical response spectra revealed much higher values for frequency bands above 5~7 Hz than Reg. Guide (1.60). The results were also compared to the Korean Standard Response Spectrum for the 3 different soil types and showed that the vertical response spectra revealed much higher values for the frequency bands below 0.2 second (5 Hz) than the Korean Standard Response Spectrum (SD soil condition). These frequency-dependent spectral values could be related to the characteristics of the domestic crustal attenuation and the effect of each site amplification. However, through the qualitative improvements and quantitative enhancement of the observed ground motions, the conservation of vertical seismic design response spectrum should be considered more significantly for the frequency bands above 5 Hz.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1997.04a
• /
• pp.136-143
• /
• 1997

본 연구에서는 철골구조물을 대상으로 지진격리(Base-Isolation)를 사용하였을 때의 진동감소 효과를 분석하기 위하여 지진하중에 대한 진동대 실험을 수행하였다. 실험 대상구조물은 $\frac{1}{4}$축소모형의 3층 철골구조물이며, 입력지진은 여러 계측기록과 UBC 설계스펙트럼으로부터 3가지 지반조건에 대하여 작성한 인공지진기록을 사용하였다. 축소 실험모형은 기초가 고정된 일반적인 철골구조물과 적층고무받침(Laminated Rubber Bearing) 형식의 지진격리장치(Base Isolator)를 사용한 구조물을 동시에 설치하여 그 지진응답을 비교 관찰하였다. 대부분의 하중하에서 지진격리장치가 사용된 철골구조물의 경우에 지진응답이 현저히 감소하는 것을 알 수 있으나, 장주기파의 성분이 강한 지반운동에 대해서는 오히려 지진응답이 증가하였다. 그러나 여러 지반조건에 대하여 UBC 시방서에서 규정한 설계하중에 대하여는 진동감소효과가 우수함을 보인다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.2 no.4
• /
• pp.123-134
• /
• 1998

본 연구에서는 지반상태가 교량의 지진응답에 미치는 영향을 분석하기 위해 다양한 지반모델 상의 교량모델에 대한 지진해석을 수행하고 그 결과를 비교.분석하였다 이를 위해서 기존의 교량시방서에서 분류된 네가지의 서로다른 지반종류를 대상으로 보다 세분된 지반모델 상에 위치하는 대표적인 교량에 대한 지진해석을 수행함으러써 첫째로는 각 지반 종류 상호간의 지진응답 차이의 정도를 시방서 값과 비교.분석하였으며 둘째로는 동일 지반으로 분류되는 상이한 두 지반간의 응답차이의 정도를 확인하였다 해석을 위해서는 시방서에서 제시된 두가지 방법 즉 단일모드 스펙트럼해석법과 다중모드 스펙트럼해석법을 사용하였으며 이들 결과를 별도로 작성된 인공시간이력을 입력으로 하는 시간이력해석법을 사용한 결과와 비교.분석하였다 시간이력해석법에서는 진동수에 무관한 지반임피던스함수를 이용하는 시간영역해석법을 사용하였다 해석결과 시방서에서 제시한 단일모드 및 다중모드 스펙트럼해석방법은 일반적으로 안전측의 지반-구조물 상호작용 해석결과를 주는 것으로 확인되었다 그러나 유연성이 큰 지반 상의 구조물에대한 지진해석을 위한 해석모델 작성시에는 지반의 유연성이 반드시 고려되어야 하며 특히 낙교방지를 위한 변위는 지반의 유연성을 고려한 정밀해석법에 의한 계산이 필수적으로 요구됨을 확인하였다.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.14-17
• /
• 2009

본 연구에서는 장대교량에서 케이블의 장력을 간편하게, 그리고 자동적으로 추정할 수 있는 저비용 무선장력계측시스템을 개발하였다. 개발된 시스템은 크게 비용이 저렴하고 설치 및 관리가 용이한 무선 기반 하드웨어와 케이블에서 계측된 가속도 데이터로부터 장력을 자동으로 추정하여 주는 내장 (Embedded) 자동화 소프트웨어로 구성된다. 저비용 무선 기반 하드웨어는 연산능력을 가진 무선계측유닛과, 계측 신호개선을 위한 신호처리보드, 그리고 상용 MEMS 가속도계로 구성되었으며, 내장 자동화 소프트웨어는 계측된 신호의 주파수 분석을 위한 FFT 모듈, 케이블의 푸리에 스펙트럼으로부터 고유진동수를 자동으로 추출하기 위한 자동 피크 추출(Peak-picking) 알고리즘 모듈, 그리고 추출된 고유진동수를 활용하여 케이블의 장력을 추정하는 진동법 모듈로 구성되었다. 개발된 시스템의 검증을 위하여, 사장교의 케이블 축소모델을 제작하고 케이블 모델에 다양한 장력과 새그를 주어 진동실험을 수행하였다. 실험 결과, 개발된 시스템은 케이블 모델의 주파수응답스펙트럼으로부터 고유진동수를 정확하게 추정하였으며, 장력과 새그의 크기에 상관없이 매우 정확한 장력을 추정하였다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.8
• /
• pp.741-746
• /
• 2007

In this study, transfer path identification and output estimation are simulated by multi-dimension spectral analysis method (MDSA). Multi -input/single-output system give expression the vehicle suspension which each inputs are correlated reciprocally. In case of correlating with inputs, the system needs separating the each input signal by MDSA. Main simulations are about finding effective input by coherent output spectrum and selecting optimal input's number by multiple coherence function. Also, by shielding transfer path of each input, transfer path characteristic is identified in terms of overall integrated contribution level.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.399-400
• /
• 2009

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.588-593
• /
• 2012

Nowadays, various forms of electro-optical rifle scope have been developed and used in order to enhance the accuracy of small arms. However, firing shock acceleration has characteristics of pyroshock having a big acceleration value with very short duration time, which the electro-optical scopes should be designed to sustain. In this paper, the firing shock acceleration, which is transmitted to the electro-optical scope, was measured and SRS (Shock Response Spectrum) analysis was performed by using the measured firing shock acceleration. Furthermore, a shock test condition using a drop-table shock tester, which can simulate the actual firing shock acceleration, was devised. The devised shock test condition will be utilized to test the electro-optical scope itself before attaching it to the small arms.