• Journal of the Korean Geotechnical Society
• /
• v.15 no.6
• /
• pp.167-185
• /
• 1999

A series of model tests was performed to find the characteristics of lateral behavior of single rigid pile. This paper shows the results of model tests on the lateral behavior of single rigid driven pile in non-homogeneous(two layered) Nak-Dong River sands. The purpose of this paper is to investigate the effect of the ratio of lower layer thickness to embedded pile length, the coefficient ratio of the subgrade reaction and the pile construction conditions(driven & embedded piles) on the characteristics of lateral behavior of single pile. The results of model tests show that the lateral behavior in non-homogeneous soil depends upon drop energy considerably, that is, in the case of H/L=0.75, as the drop energy increases three times the decrease percentage increases about 2.12 times. In the driven pile with non-homogeneous soil of $E_{h1}/E_{h2}=5.56$, the effect of upper layer with large stiffness on the decrease of lateral deflection is remarkably smaller than embedded pile. In non-homogeneous soil, the maximum bending moment of driven pile is in the range of 100 132% in comparison with embedded pile. The reason is that the stiffness of soil around pile increases with drop vibration and so the pile behavior is similar to the flexible pile behavior by means of the increase of relative stiffness of pile, In this paper, the experimental equations for lateral load and H/L on $y_D/y_E \; & \; MBM_D/MBM_E$ are suggested from model tests.

• Applied Chemistry for Engineering
• /
• v.10 no.1
• /
• pp.105-111
• /
• 1999

When the preparation method of iron silicide films possess the annealing process, the interfacial state of the films is not fine. The good quality films were obtained as the plasma was used without annealing processing. Since the injected precursors were various active species in the plasma state, the organic compound was contained in the prepared films. We confirmed the formation of Fe-Si bonds as well as the organic compound by Fe and Si vibration mode in Raman scattering spectrum at $250cm^{-1}$ and Ft-IR. Because of epitaxy growth being progressed by the high energy of plasma at the low temperature of substrate, iron silicide was epitaxially grown to ${\beta}$-phase that had lattice structure such as [220]/[202] and [115]. Band gap of the prepared films had value of 1.182~1.174 eV and optical gap energy was shown value of 3.4~3.7 eV. The Urbach tail and the sub-band-gap absorptions were appeared by organic compound in films. We knew that the prepared films by plasma were obtained a good quality films because of being grown single crystal.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.1
• /
• pp.92-100
• /
• 2018

Vortical systems are considered a main feature to sustain turbulence in a boundary layer through interaction. Such turbulent structures result in frictional drag and erosion or vibration in engineering applications. Research for controlling turbulent flow has been actively carried out, but in order to show the effect of vortices in a turbulent boundary layer, it is necessary to clarify the mechanism by which turbulent energy is transferred. For this purpose, it is convenient to demonstrate and capture phenomena in a laminar boundary layer. Therefore, in this study, the interactions of disturbed flow around a hemisphere on a flat plate in laminar flow were analyzed. In other words, a street of hairpin vortices was generated following a wake region formed after flow separation occurred over a hemisphere. Necklace vortices surrounding the hemisphere also appeared due to a strong adverse pressure gradient that brought high momentum fluid into the wake region thereby leading to an increase in the frequency of hairpin vortices. To mitigate the effect of these necklace vortices, local suction control was applied through a hole in front of the hemisphere. Flow visualization was recorded to qualitatively determine flow modifications, and hot-film measurements quantitatively supported conclusions on how much the power of the hairpin vortices was reduced by local wall suction.

• Korean Journal of Remote Sensing
• /
• v.33 no.2
• /
• pp.249-255
• /
• 2017

Antarctica isimportant area in order to understand climate change. In addition, this area is complex region where indicate warming and cooling trend according to previous studies. Therefore, it is necessary to understand the long-term variability of Antarctic energy budget. Net radiation, one of energy budget factor, is affected by albedo, and albedo cause negative radiative forcing. It is necessary to analyze a relationship between albedo and net radiation in order to analyze relationship between two factors in Antarctic climate changes and ice-albedo feedback. In thisstudy, we calculated net radiation using satellite data and performed an analysis of long-term variability of net radiation over Antarctica. In addition we analyzed correlation between albedo. As a results, net radiation indicates a negative value in land and positive value in ocean during study periods. As an annual changes, oceanic trend indicates an opposed to albedo. Time series pattern of net radiation is symmetrical with albedo. Correlation between the two factors indicate a negative correlation of -0.73 in the land and -0.32 in the ocean.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.15 no.5
• /
• pp.35-44
• /
• 2011

PGA (Peak Ground Acceleration) is the parameter which indicates the peak value for strong ground motion and is mainly due to the intensity of the seismic wave. Usually, seismic waves can consist of different characteristics and can have different effects on structures. Therefore, it may be undesirable that the effects of a seismic wave are evaluated only based on the PGA. In this study, time history analysis was executed with a single degree of freedom model for inelastic seismic analysis. The numerical model was assumed to be a perfect elasto-plastic model. Input accelerations were made with El Centro NS (1940), other earthquake records and artificial earthquakes. The displacement ductility demand and cumulative dissipated energy, which were calculated from other artificial earthquakes, were compared. As a result, different responses from other seismic waves which have the same PGA were identified. Therefore, an index which could reflect both seismic and structural characteristics is needed. The SI (Spectrum Intensity) scale which could be obtained from integration by parts of the velocity response spectrum could be an index reflecting the inelastic seismic response of structures. It can be possible to identify from correlation analysis among the SI scale, displacement ductility demand and cumulative dissipated energy that the SI scale is sufficient to be an index for the inelastic response of structures under seismic conditions.

• Korean Chemical Engineering Research
• /
• v.51 no.1
• /
• pp.35-41
• /
• 2013

Properties of $NaBH_4$ hydrolysis reaction using Co-P-B/FeCrAlloy catalyst and the catalyst durability were studied. Co-P-B/FeCrAlloy catalyst showed low activation energy such as 25.2 kJ/mol in 5 wt% $NaBH_4$ solution, which was similar that of noble metal catalyst. The activation energy increased as the $NaBH_4$ concentration increased. Formation of gel at high concentration of $NaBH_4$ seriously affected hydrogen evolution rate and the catalyst durability. The catalyst loss decreased as reaction temperature increased due to lower gel formation when the concentration of $NaBH_4$ was over 20 wt%. Considering hydrogen generation rate and durability of catalyst, the catalyst supported with FeCrAlloy heat-treated at $1,000^{\circ}C$ without ultra vibration during dipping and calcination after catalyst dipping was best catalyst. To use catalyst more than three times in 25 wt% $NaBH_4$ solution, it should be reacted at higher temperature than $60^{\circ}C$.

• Economic and Environmental Geology
• /
• v.48 no.1
• /
• pp.89-101
• /
• 2015

The sour gas is natural gas containing components such as hydrogen sulphide and carbon dioxide that form acids when mixed with water. Element sulfur precipitates from sour gas when reservoir pressure and temperature decrease. According to the International Energy Agency, about 43% of the world's natural gas reserves(2,580 tcf or 73.057 tcm), excluding North America, are sour. The sour gas is often derived from the Germanic word 'sauer or acidic' and the etymology referred to as 'sour'. Sour gas requires special handling and infrastructure because it contains significant amounts of hydrogen sulphide, making it highly corrosive, flammable and explosive, and there fore more costly and dangerous to process. So the business of sour gas is affected by two important factors: the economic value of the gas, and the methods used in its production. According to be analyzed in the academic literature to sour gas(2000~2014) by the program of 'web of science', the research activities 145 papers in sour gas.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.112-112
• /
• 1999

고분자 표면에 MeV급 이온을 주입하게 되면 화학적, 광학적, 물리적, 전기적 특성 등 기존의 재래식 공정으로는 불가능한 다양한 특성변화가 일어나게 된다. 본 실험에서는 이온 조사에 따른 micro-hardness의 변화에 중점을 두어 관찰하였다. 수 MeV로 가속시킨 Cl과 C 이온을 Kapton, Teflon, PMMA에 조사량을 바꾸어가며 조사하였다. 이때 조사 전후 고분자 시료의 표면 경도는 depth-sensing nanoindentation technique (Nano Indenter II, USA)을 이용하여 측정하였다. 측정깊이는 극표면 효과와 기측효과의 영향을 무시할 수 없는 100nm로 결정하였다. 또한 이와 같은 경도변화를 규명하기 위하여 각각의 시료에 대해 FTIR, Raman, UV-VIS, RBS, XPS 스펙트럼을 측정하였으며, 조사중에 발생되는 가스상 분자들을 RGA를 이용하여 측정하였다. 1 MeV Cl 이온을 Kato에 4x1015ions/cm2 조사하면 경도가 0.35 GPa에서 7.1GPa로 약 20배 정도 증가하게 되며, 이 경도는 stainless steel 경도 2~3 GPa, martensite steel 8~12와 비교하여 보면 상당히 높은 수준임을 알 수 있다. Teflon과 PMMA 시료의 경우 1MeV Cl 이온 4X1015ions/cm2를 조사시키면 각각 경도가 0.31GPa에서 4.1a, 0.30 GPa에서 3.9GPa로 변화하였으며 Kapton에 비하여 상대적으로 경도의 변화가 적음을 알 수 있었다. 이온 주입된 Kapton의 경우 FT-IR측정에 의하여 이온 조사량이 증가함에 따라 C=O 진동, 이미드그룹의 CONH, tertiary amine의 C-N 흡수 피크가 감소되며, 1X1014ions/cm2 이상의 양이 조사되어야 개질변화가 일어남을 알 수 있었다. XPS 측정 결과 Kapton에 조사되는 이온양이 증가할수록 C=O, C-O 및 C-N의 탄소는 감소하고 페닐고리 탄소가 증가함을 알 수 있었다. 또한 이온 조사 중 측정한 RGA에서도 CO 가스가 대량 방출되는 현상을 관찰하였으며 FTIR 및 XPS에서의 C=O 결합의 감소와도 일치하였다. RBS에 의한 CNO 원소의 변화에서도 다른 원소보다 O의 감소가 현저하게 나타남을 확인하였다. UV-VIS 측정을 통해 조사 이온량에 따라 에너지 준위가 변동하여 흡수스펙트럼이 장파장으로 확대됨을 알 수 있었으며, 이는 공액 2중 결합의 형성에 의한 $\pi$-전자 및 기타 결함에 기인한다. PMMA 및 Teflon의 경우 FTIR 측정에 의하여 이온 조사됨에 따라 function group 들의 peak가 세기가 감소되면서 완만해지는 경향을 보이며 원래의 구조를 상실하게 된다. PMMA와 Teflon은 이온 조사가 되면 가교형서보다는 사슬절단이 주로 일어나므로 가교형성이 잘 일어나는 Kapton보다는 상대적으로 경도의 증가가 적음을 알 수 있었다.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.11a
• /
• pp.63-63
• /
• 2002

현재 기계적 합금화법에서는 주로 합금을 구성하는 성분원소 분말을 불활성분위기에서 볼밀처리 함으로써 함금화를 시키거나 모합금에 산화물을 분산시켜 복합화시키는 공정을 통하여 각종 화합물, 비정질상 및 과포화고용체등의 준안정상의 합성 뿐만이 아니라 초미세조직의 생성에 관한 폭 넓은 분야의 연구가 행하여지고 있다. 한편 MA에서는 볼멀처리중 기계적 에너지의 투여에 의하여 실제 반응온도보다 낮은 온도에서 발생하는 특이한 화학반응 즉 Mechanochemical 반응을 일으키 기도 한다. 본 연구에서는 헤마타이트($Fe_20_3$)와 금속윈소인 Ti의 MA처리에 의하여 고상환원반응 을 유기시켜 $Fe-TiO_2$계 nanocomposite 분말재료를 제조하고자 한다. 특히 MA 공정에 있어서 자기 물성의 변화와 X선 회절을 통하여 고상환원반응에 의한 복합분말의 생성과정을 조사하였다. 출발원료는 $Fe_20_3$(고순도화학제,99.9%, 평균입경 0.1$\mu\textrm{m}$)와 금속원소인 Ti(99.9%, 명균업경 150$\mu\textrm{m}$)을 몰비 2:3의 조성이 되도록 하여 MA를 실시하였다. 볼멀은 고에너지 유성형 볼밀장치(독일 제, Fritsch P-5)를 이용하였으며 진공치환형 용기에 원료분말을 장입하여 2회정도 진공배기한 후 아르곤 가스를 충전하여 볼밀을 행하였다. 얻어진 분말시료에 대하여 x-선 회절장치, 전자현미경 (SEM) 및 진동시료형자력계(VSM)를 통하여 결정구조, 미셰조직 빛 자기특성을 조사하였다. $Fe_2O_3-Ti$ 혼합분말의 MA처리 에 의하여 초기단계부터 환원반응과 함께 $Fe_3TIO_{lO}$ 중간상이 관찰 되었으나 30hrs의 MA처리 후 Fe와 산화물 $TiO_2$로 모두 환원되어 $Fe-TiO_2$계 나노복합분말이 얻어짐을 알 수 있었다. 이 때 X션 회절피크의 line broadening으로부터 복합분말의 Fe 명균 결정립 크기는 24nm로 초미세 결정럽의 분말합금이었다. 포화자화값은 볼밀처리에 따라 점점 증가하여 MA 30시간에는 20.3emu/g로 포화됨을 알 수 있었다. 또한 보자력 Hc는 MA초기단계에 350e로 매우 낮으나 30시간 후에는 Hc값이 2600e로 매우 큰 값을 나타내었다. 이것은 환원반응결과 초기에 생성된 Fe의 결정립이 비교적 크고 결정결함이 적으나 볼밀처리를 30시간까지 행하면 Fe 결정렵의 미세화 빛 strain 증가로 magnetic hardening이 일어나기 때문인 것으로 사료된다.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.2
• /
• pp.132-138
• /
• 2009

The energy efficiency and environment-friendly aspect of the railway system would be superior to other on-land transportation systems. In a preliminary feasibility study stage and selection of optimal railway corridor, the energy efficiency and problems related to environment are usually not considered. For the selection of optimal railway corridor, geographical features and facility of management are generally considered. Environment effect factors for the selection of environment-friendly railway corridor are focused and studied in this paper. In this study, various analysis of opinion of specialists (railway, environment, transport, urban planning, survey) and the guideline for construction of environment-friendly railway were accomplished. From these results of various analysis, 7 major categories (topography/geology, flora and fauna, Nature Property, air quality, water quality, noise/vibration, visual impact/cultural assets) were extracted. To select environment friendly railway corridors, many alternatives should be compared optimal corridor must be selected by a comprehensive assessment considering these 7 categories. The investment for railway systems can be encouraged by the considering of main environmental effect factor evaluated with the modified environmental weight factors for environment-friendly railway construction.