• Journal of the Korea Convergence Society
• /
• v.5 no.2
• /
• pp.13-18
• /
• 2014

In this study, two models due to the configuration of ripper at excavator are investigated by structural and fatigue analyses. The maximum stress and deformation are happened at the axis connected with the body of working device and the direct working part respectively. Model 1 is thought to have more structural durability than model 2. Fatigue life or damage in case of 'SAE bracket history' whose load change is most severest among non-uniform fatigue loads is shown to become most unstable. But life or damage in case of 'Sample history' whose load change is slowest among non-uniform fatigue loads is shown to become most stable. These study results can be effectively utilized with the design of ripper at excavator by anticipating and investigating prevention and durability against its fatigue damage.

• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.292-299
• /
• 2012

We made 8 wt% silica dispersion system with fumed silica and photo curable acrylic monomer by beads mill process. These dispersions could be applied in organic/inorganic hybrid coating systems. These dispersions could be applied in organic/inorganic hybrid coating systems. The 4 species of photo curable acrylic monomer which was presence of hydroxyl group, different solubility parameter, and different molecular size were used in the silica dispersions. Stability of polar solvent, isopropyl alcohol, in silica dispersions was investigated. We investigated the stability of silica dispersions by using steady-state and dynamic rheology. As the monomer has hydroxyl group increased in mono and binary monomer silica dispersions, they showed non flocculated stable sol (loss modulus (G")> storage modulus (G')). When polar solvent IPA was added into slightly flocculated silica dispersions, they changed to non flocculated stable sol.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.3
• /
• pp.437-443
• /
• 1987

An optimal design to improve the ride quality was performed with the time and frequency domain analysis based on both of deterministic and random road profiles. The objective function is established to minimize the absorbed power while the constraints are taken so as to satisfy the condition for the stability of vehicle. The result of the optimal design shows that the rms for the acceleration of a driver and his seat is within the critical values for the ride quality from ISO. The optimal values obtained show that the maximum absolute acceleration of the driver and his seat has significantly been reduced and the reference limits on the relative displacement have satisfied their feasibility. As the optimal value according to a specific speed is the results from the optimization process, a global optimum value should be determined to be the one which gives th minimum values of total sum of absorbed power with respect to various speed.

• The KSFM Journal of Fluid Machinery
• /
• v.7 no.5 s.26
• /
• pp.20-28
• /
• 2004

Static and dynamic structural analyses of a turbine bladed-disk for a liquid rocket turbopump are performed to investigate the safety level of strength and vibration at design point. During operation, turbopump is exposed to various external loads. Therefore, the effects of them should be carefully considered and properly modeled. First, due to the high rotational speed of the turbopump, effects of centrifugal forces are considered in the structural analysis. Thermal load caused by severe temperature differences is also considered. A three dimensional finite element method (FEM) is used for linear and nonlinear structural analyses with modified Newton-Raphson iteration method. After the nonlinear solution is obtained from the structural analysis, dynamic characteristics are obtained as a function of rotational speed from the linearized eigenvalue analysis at an equilibrium position. From the analysis results, characteristics of stress distribution and vibration were thoroughly examined and investigated.

• Journal of KIISE:Information Networking
• /
• v.29 no.2
• /
• pp.174-180
• /
• 2002

With the invention of MPLS and the Improvement in traffic engineering, multipath packet forwarding and dynamic load control has become a reality. A dynamic load control, while it can improve network efficiency by controlling loads between paths according to the network state, can lead to unstable and oscillating state because of the staleness of the state information. In this paper, we propose a efficient load control scheme which remains stable. The proposed scheme introduces prediction to reduce the staleness of state message and to prevent oscillation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.7
• /
• pp.21-27
• /
• 2022

This study was conducted to evaluate the structural stability of a CNC automatic lathe structure and avoid resonance. The analysis conditions were analyzed by applying the weight of the upper assembly. From the structural analysis, the stress and deformation were low, and the safety factor was high. From the dynamic characteristic analysis, it was determined that resonance does not occur because the natural frequency is outside the driving range. The error between the dynamic characteristic analysis and vibration test results is very low; thus, the reliability of the analysis results can be secured.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.1A
• /
• pp.125-133
• /
• 2008

According to longer and longer span, dynamic instability of stay cable should be prevented. Dynamic instability occurs mainly symmetric 1st mode and antisymmetric 1st mode in stay cable. Especially symmetric 1st mode has a lot of influence on sag. Therefore fundamental frequency of stay cable is different from that of taut sting. Irvine, Triantafyllou, Ahn etc. analyzed dynamic behavior of taut cable with sag through analytical technical and their researches give important results for large bounds of Irvine parameter. But each research shows mutually different values out of characteristic (cross-over or mode-coupled) point and each solution of frequency equations of all researchers can be very difficultly found because of their very high non-linearity. Presented study focuses on fundamental frequency of stay cable. Generalized mechanical energy with symmetric 1st mode vibration shape satisfied boundary conditions is evolved by Rayleigh-Ritz method. It is possible to give linear analytic solution within characteristic point. Error by this approach shows only below 3% at characteristic point against existing researches. And taut cable don't exceed characteristic point. I.e. high accuracy, easy solving techniques, and a little bit limitations. Therefore presented study can be announced that it is good study ergonomically.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.3
• /
• pp.41-48
• /
• 2014

Experimental study of sedimentation and self-weight consolidation has been primary research area in dredged soil. However, good quality of the dredged soil and minimum water pollution caused by the pumping of reclaimed soil require intensive study of the flow characteristics of dredged material due to dumping. In this study, continuity and the equilibrium equations for mass flow assuming single phase was derived to simulate mass flow in dredged containment area. To optimize computation and modeling time for three dimensional geometry and boundary conditions, depth integration is applied to governing equations to consider three dimensional topography of the site. Petrov-Galerkin formulation is applied in spatial discretization of governing equations. Generalized trapezoidal rule is used for time integration, and Newton iteration process approximated the solution. DG and CDG technique were used for weighting matrix in discontinuous test function in dredged flow analysis, and numerical stability was evaluated by performed a square slump simulation. A comparative analysis for numerical methods showed that DG method applied to SU / PG formulation gives minimal pseudo oscillation and reliable numerical results.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.3
• /
• pp.241-249
• /
• 2004

There is an over head hoist transporter(OHT) by the system for delivering the wafer in semiconductor processing. The transfer system consist of carrier, vehicle, rail and support. The Tail supporting the wafer and the transfer system should maintain enough strength and stiffness. To achieve lightness and enough strength and stiffness, optimization algorithm should be introduced in design process. In this study, two kinds of section shapes as L-type, C-type is carried out the structure analysis and optimization. Total weight of rail is to be minimized while displacement should not exceed limit. To improve the initial model, topology optimization is done by the plain problem. Size optimization is done with 3D solid element and PLBA algorithm, the RQP algorithm. The weight of optimum model as L-type, C-type is decreased by 2.3%, 10% respectively. It is improved better than the initial model in the strength and stiffness of the structure.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.90-90
• /
• 2017

생력화를 위한 구기자의 수확 기계화는 열악한 수확작업환경을 쾌적한 작업환경으로 개선하고 노동력 감소, 생산비 절감을 할 수 있다. 관행 손 수확과 진동 고리형 수확기 방법보다 높은 작업 능률 향상으로 영농규모의 확대 촉진 및 안정적인 영농 구조를 구축하여 재배농가의 생산비를 절감하여 경쟁력을 높일 수 있으며, 기존 인력에 의존하였던 수확작업을 기계화함으로서 전업농 및 대단위 경작이 가능하게 함으로서 국내에서 생산한 양질의 구기자를 국민에게 안정적으로 제공할 수 있다. 따라서, 본 연구는 구기자 수확작업의 생력화를 위하여 개발 보급된 수목형의 재배법 특성을 분석하고 이를 토대로 타격장치를 적용한 보행형 구기자 수확기를 개발하는데 목적이 있다. 수목형 구기자나무의 분지에 착과되어 있는 숙과를 주행하면서 탈과 할 수 있는 탈과 장치를 제작하기 위하여 타격형 탈과 장치를 3D 모델링 작업(Inventor V.11, Autodesk, USA) 후 시작기를 제작, 구기자 수확 시작기는 주행부, 타격장치, 집과부, 분지유인부로 구성하였다. 구기자 수확 시작기의 최대 높이는 형태학적 특성을 토대로 타격봉의 높이를 900 mm 이하로 제한하였으며, 조향장치의 높이는 800 mm로 하였다. 주행부는 구기자 재식 조사결과를 이용하여 고랑 폭 1,500 mm 이하에서 자유롭게 전 후진 이동이 가능하고 경사로 등을 주행 시에도 안전성을 높이기 위해 자동브레이크 기능이 있으며 타격장치의 타격 봉은 알루미늄 재질로 지름 100 mm, 길이 400 mm로 설계 제작하였으며, 구기자 분지 타격 시 분지와 타격 봉이 수직 상태로 타격이 가능하도록 제작, 집과장치는 포장의 두둑, 고랑은 일괄 표준화가 되어 있지않아 청양구기자시험장에서 측정한 재배법을 바탕으로 설계된 수집부 프레임의 적용범위는 폭 450 mm, 길이 720 mm, 높이 1,500 mm를 집과 범위로 하여 설계 제작하였다. 타격 방식을 적용한 구기자 수확기 성능평가 결과 조숙기에 30초 이상의 탈과 시 87.5 % 이상 탈과는 어려울 것으로 판단되었으며, 성숙기에는 타격시간에 관계없이 92 %의 매우 우수한 탈과율이 나타났다. 성숙기의 주행속도 48 m/h 일 때 탈과율과 집과율은 89 %, 92 %로 나타났다.단위작업시간당 최대 수확 능력은 관행작업 2.9 kg/hr, 진동고리형 수확기 5.2 kg/hr, 타격방식을 적용한 구기자 수확기는 최소 7.6 kg/hr, 최대 24.1 kg/hr로 관행작업과 비교하여 주행속도와 시기별 최소 2.6배, 최대 8.3배의 작업 성능 차이가 나타났다. 재배양식에서는 기계화 수목형이 적합한 것으로 나타났고, 타격방식을 적용한 보행형 구기자 수확기를 이용하여 수형별 시간대별 수확성능을 시험한 결과 우수한 결과가 나타났다. 이에 따라 구기자 재배 농가에 기계화수목형 재배법을 보급하고 타격방식을 적용한 구기자 수확기를 이용하면 작업환경 개선과 노동력, 인건비 절감을 통한 영농규모의 확대 촉진 및 안정적인 영농 구조로 구기자 경쟁력 제고를 할 수 있을 것으로 판단되어진다.