• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.5
• /
• pp.363-363
• /
• 2001

• Proceedings of the SAREK Conference
• /
• 2005.06a
• /
• pp.50-50
• /
• 2005

• Proceedings of the SAREK Conference
• /
• 2005.06a
• /
• pp.128-128
• /
• 2005

• The Magazine for Energy Service Companies
• /
• s.62
• /
• pp.58-65
• /
• 2010

최근 가정용 컴퓨터와 노트북 등의 중앙처리장치(CPU) 속도가 급격히 빨라지고 있다. 더욱이 화석 에너지 고갈 위기에 따라 제품의 발열량은 급속도로 늘어날 전망이라는 관측이 나왔다. 때문에 에너지절약에 대한 해결이 동반된 연구가 이뤄져야 한다는 목소리가 커지고 있다. 이러한 문제를 해결하기 위해 발열원에 히트싱크를 직접 부착하는 강제대류 방식에 대한 연구가 진행되고 있고, 최근 들어 열전소자를 이용한 냉각방식과 히트파이프를 이용한 방식도 대두되고 있다. 그 중 열저항 특성 연구에 집중했던 기존 방식에서 벗어나 Pulsating Heat Pipe(PHP)를 열확산기로 적용시킨 연구방식을 소개한다.

• Resources Recycling
• /
• v.15 no.3 s.71
• /
• pp.30-37
• /
• 2006

For keeping the indoor air quality, we develop the pulsating heat pipe(PHP) type heat recovery ventilator using an used radiator for vehicles. We compare the PHP type with existing model. There are some merits that are able to change the unit number according to heat load and show us the similar performance to existing models.

• Journal of the Korean Society of Visualization
• /
• v.21 no.3
• /
• pp.57-64
• /
• 2023

An open pulsating heat pipe operates continuously by inflow and outflow fluids through an open-type condenser. The open pulsating heat pipe is a device capable of obtaining the thrust due to the variation of internal pressure during phase change. Therefore, the open pulsating heat pipe is a suitable device to move fluids if the heat source such as waste heat exists. Many numerical studies have not been sufficiently conducted on the open pulsating heat pipe. In this study, the numerical analysis of the open pulsating heat pipe is performed according to the length of the condenser section. The OpenFOAM software is used to obtain the thrust and the flow visualization for the open pulsating heat pipe.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.8
• /
• pp.1016-1021
• /
• 2011

The enhancement for cooling performance of heat sink is surely necessary to guarantee the performance of electronic products. So in this paper, the cooling performances of the aluminum heat sink with pulsating heat pipe(PHP) were investigated experimentally and numerically. The pulsating heat pipe was used as a heat spreader. Working fluid of PHP was R-22. Heat inputs were 30W, 60W, 80W and 100W, respectively. Heat sink was tested for forced convection conditions with air velocity of 1 ~ 4m/s. And CFD simulations were conducted for two different heat sinks. The results showed that the cooling performance of heat sink with pulsating heat pipe was higher than that of conventional heat sink. Therefore, the pulsating heat pipe can be a good tool to improve cooling performance of heat sink.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.9
• /
• pp.853-859
• /
• 2000

In this study, low temperature waste heat recovery heat exchanger was developed using a principle of self-excited oscillating heat pipe. The heat exchanger of serpentine type was composed of extruded flat aluminum tube with 6 channels (3 nm$\times$ 2.75nm) and louvered fin. The heat transfer area density of heat exchanger was $331.9 m^2/m^3$. Working fluid is R141b and charge ratio was 40% by volume. Heat transfer rate and the effectiveness of heat exchanger was primary concern of this study. As a result, the effectiveness of heat exchanger was about 0.4-0.67, and recovered waste heat rate was about 4.5 kW per one unit of heat exchanger.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1499-1505
• /
• 2003

Rapid development of electronic technology requires small size, high density packaging and high power of electronic devices. So, in this paper, characteristics on oscillating heat pipe according to operating conditions(environment temperature, charging ratio of working fluid, inclination) based on experimental study was investigated. From the experimental results, $25^{\circ}C$environment temperature), R-141b(working fluid)40%(charging ratio) was best performace at others of inclination angle and The top heating mode of OCHP performed 80% efficiency of the bottom heating mode.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.8
• /
• pp.741-747
• /
• 2004

The purpose of this study was to develop a cooler/heater using a thermoelectric module combined with a parallel flow type oscillating heat pipe with R-142b as a work ing fluid. The experiment was performed for 16 thermoelectric modules (6 A/15 V, size: 40${\times}$40${\times}$4 mm), varying design parameters of the heat pipe (inclination angle, working fluid charging ratio, etc) . Experimental results indicate that the optimum charging ratio and the inclination angle of the parallel flow type oscillating heat pipe were 30% by volume and 30%, respectively. The maximum cooler/heater capacity were 479W (COP : 0.47) and 630W (COP : 0.9), respectively.