• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.2
• /
• pp.17-25
• /
• 2006

In the present study, a 2-D chimera technique for overlapped bodies in relative motion is developed using unstructured triangular meshes. The solid boundary nodes located next to the intersecting point between bodies are merged to the intersecting point to assure accurate representation of the intersecting region. In order to assign proper value of flow variables at the nodes located out of the computational field, interpolation is conducted for non-active nodes. For validation, the motions of a NACA64A006 airfoil and a NACA0012 airfoil with a plane flap are computed and the results are compared with other simulations. The motion of a launching missile ejected from a NACA0012 airfoil is also simulated.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.9 no.4
• /
• pp.128-136
• /
• 2006

The purpose of this paper is to examine the dynamic stall characteristics of an elliptic airfoil when subject to constant pitch motions. In this study, which was motivated by the pressing need for a greater understanding of the reduced frequency$({\kappa})$ effects on flow patterns of elliptic airfoil, the various reduced frequencies were considered. The result confirms that the reduced frequency has a profound effects on the flow patterns. The increase of ${\kappa}$ accelerate the separation bubble bursting process up to ${\kappa}=0.10$, then diminish with further increase in ${\kappa}$. Compared with static condition, the dynamic pitching airfoil delays stall angle approximate $4{\circ}{\sim}5{\circ}$ during pitch-up stroke for ${\kappa}=0.10$. Results from this qualitative analysis provided valuable insight Into the control of dynamics stall.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.8
• /
• pp.809-815
• /
• 2009

The previous work(Cheong et al., 2006) where the characteristics of acoustic emissions of wind turbines has been investigated according to the methods of power regulation, has showed that the acoustic power of wind turbine using the stall control for power regulation is more correlated with the wind speed than that using the pitch control. In this paper, basically extending this work, the noise generation characteristics of large modern upwind wind turbines are experimentally indentified according to the power regulation methods. To investigate the noise generation mechanisms, the distribution of noise sources in the rotor plane is measured by using the beam-forming measurement system(B&K 7768, 7752, WA0890) consisting of 48 microphones. The array results for the 660 kW wind turbine show that all noise is produced during the downward movement of the blades. This result show good agreement with the theoretical result using the empirical formula with the parameters: the convective amplification; trailing edge noise directivity; flow-speed dependence. This agreement implies that the trailing edge noise is dominant over the whole frequency range of the noise from the 660 kW wind turbine using the pitch control for power regulation.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.4
• /
• pp.12-19
• /
• 2007

In this study, nonlinear flow-induced vibration(flutter) analyses of a 2-DOF launch vehicle airfoil have been conducted in supersonic and hypersonic flow regimes. Advanced aeroelastic analysis system based on computational fluid dynamics and computational structural dynamics is successfully developed and applied to the present analyses. Nonlinear unsteady aerodynamic analyses considering strong shock wave motions are conducted using inviscid Euler equations. Aeroelastic governing equations for the 2-DOF airfoil system is solved by the coupled integration method with interactive CFD and CSD computation procedures. Typical wedge type airfoil shapes with initial angle-of-attacks are considered to investigate the nonlinear flutter characteristics in supersonic(15). Also, the comparison of detailed aeroelastic responses are practically presented as numerical results.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.6 s.99
• /
• pp.687-696
• /
• 2005

Acoustic power spectrum of the upstream and downstream sound field due to an isotropic frozen turbulent gust impinging on a cascade of flat plate airfoils are computed by using a analytic formulation derived from Smith's method, and Whitehead's LINSUB codes. A parametric study of the effects on sound power of the number of blades and turbulence length scale is performed with an emphasis on analyzing the characteristics of sound power spectrum. Through the comparison of the computed results of sound power, it is found that acoustic power spectrum from the 2-D cascade subject to a ingested turbulence can be categorized into two distinct regions. one is lower frequency region where some spectral components of turbulence do not contribute to the cut-on acoustic modes and therefore the effect of the cascade geometry is more dominant ; the other is higher frequency region where all of spectral components of turbulence make contributions to cut-on acoustic modes and thus acoustic power is approximately proportional to the blade number.

• Proceeding of EDISON Challenge
• /
• 2014.03a
• /
• pp.579-584
• /
• 2014

고속 열차의 속도가 점점 빨라짐에 따라 고속 열차 주행 시 발생하는 여러 공력적인 문제가 대두되고 있다. 그 중 고속 열차와 전력선을 이어주는 판토그래프에서의 소음 발생과 압상력 불안정 문제가 중요시 되어왔고 이에 대한 여러 선행연구가 진행되고 있다. 지금까지의 선행 연구는 원형, 사각형, 에어포일과 같이 기본적인 형상을 이용한 판토그래프 팬헤드의 최적 단면 형상을 찾는 데에 초점을 맞추고 있다. 본 연구는 이러한 주류의 접근 방식에서 벗어나 팬헤드에 구멍을 추가하여 그 효과를 보는 다양한 시도를 해보았고 구멍이 소음 발생과 압상력 불안정에 미치는 영향에 대하여 연구하였다.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1795-1800
• /
• 2003

An experimental study was carried out to investigate near-wake characteristics of an elliptic airfoil oscillating in pitch. The airfoil was sinusoidally pitched about the half chord point between $-5^{\circ}C$ and $+25^{\circ}C$ angles of attack at the freestream velocities of 3.4 and 23.1 m/s The corresponding Reynolds numbers based on the chord length were $3.3{\times}10^4$ and $2.2{\times}10^5$, respectively. A hot-wire anemometer was used to measure the near-wake flow variable at the reduced frequency of 0.1. Ensemble-averaged velocity and turbulence intensity profile were presented to examine the near-wake characteristics depending on the Reynolds number. The axial velocity deficit in the near-wake region tend to decrease with the increase in the Reynolds number a found in many stationary airfoil test . Turbulence intensity in the near-wake region have a tendency to decrease with the increase in the Reynolds number during the pitch-up motion, whereas it shows different feature during the pitch-down motion either the laminar boundary layer or turbulent boundary layer separation.

• Proceedings of the Korea Contents Association Conference
• /
• 2011.05a
• /
• pp.553-554
• /
• 2011

자동차, 선박, 기계부품 등의 분야에서 고성능 컴퓨터를 활용한 공학 시뮬레이션 기술은 이미 널리 활용되고 있으며, 바이오, 나노뿐 아니라 금융 분야까지 확대되고 있는 추세이다. 공학 시뮬레이션을 수행하기 위해서는 CFD(Computational Fluid Dynamics), 기계구조, 병렬수치해석 등에 대한 고급 지식이 요구되는데, 이로 인해 산업체에서의 활용이 활발하지 못한 것이 현실이다. 이러한 문제를 해결하기 위한 하나의 대안으로 공학 시뮬레이션 프로세스의 자동화 기술이 등장했으며, 열유체, 피로내구, 진동, 충돌 등의 분야에서 특정제품이나 기술에 대한 시스템이 제안되었다. 국내에서는 에어포일(airfoil), 팬(fan), 기어(gear) 등의 제품이나 주조 기술에 대해 공학 시뮬레이션 자동화가 시도되었다. KISTI에서는 축류팬(axial fan) 시뮬레이션 자동화에 대해 프로토타입 시스템을 구축하였으며, 현대차에서는 자동차 부품에 대한 시뮬레이션 자동화 시스템을 구축하여 활용하고 있다. 미국 OSC(Ohio Supercomputer Center)의 경우 용접기술에 대한 시뮬레이션 자동화 시스템을 웹상에 구축하여 서비스를 오픈하였으며, 현재 전 세계 200여 기업이 이용하고 있다. 공학 시뮬레이션 자동화 기술이 보다 발전하기 위해서는 시뮬레이션 결과의 신뢰성, 적용 가능 분야 및 제품의 확대, 데이터보안 등이 확보되어야 한다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.11
• /
• pp.1049-1055
• /
• 2008

Modern multidisciplinary computational fluid dynamics often incorporates moving boundaries, as would be required in the applications such as design optimization, aeroelasticity, or forced boundary motion. It is challenging to develop robust, efficient grid deformation algorithms when large displacement of the moving boundaries is required. In this paper, a volume grid deformation code is developed based on the finite macro-element and the transfinite Interpolation, and then interfaces to a structured multi-block Navier-Stokes in-house code. As demonstrated by an airfoil with pitching motion, the hysteresis loops of lift, drag and moment coefficients of the developed method are shown to be in good agreement with those of experimental data.

• Journal of computational fluids engineering
• /
• v.18 no.1
• /
• pp.1-6
• /
• 2013

Missile and fighter aircraft have been challenged by low restoring nose-down pitching moment at high angle of attach. The consequence of weak nose-down pitching moment can be resulting in a deep stall condition. Especially, the pressure oscillation has a huge effect on noise generation, structure damage, aerodynamic performance and safety, because the flow has strong unsteadiness at high angle of attack. In this paper, the unsteady aerodynamics coefficients were analyzed at high angle of attack up to 50 degrees around two dimensional NACA0012 airfoil. The two dimensional unsteady compressible Navier-Stokes equation with a LES turbulent model was calculated by OHOC (Optimized High-Order Compact) scheme. The flow conditions are Mach number of 0.3 and Reynolds number of $10^5$. The lift, drag, pressure, entropy distribution, etc. are analyzed according to the angle of attack. The results of average lift coefficients are compared with other results according to the angle of attack. From a certain high angle of attack, the strong vortex formed by the leading edge are flowing downstream as like Karman vortex around a circular cylinder. The primary and secondary oscillating frequencies are analyzed by the effects of these unsteady aerodynamic characteristics.