• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.5
• /
• pp.74-82
• /
• 2004

This paper describes the speed control of the surface-mounted permanent-magent synchronous motors (SMPMSNM) for elevator drive. The elevator motor needs to be a compact and slim type. Essentially, the proposed scheme uses a vector control algorithm for a speed and torque control and Anti-windup technique is adopted to prevent a windup phenomenon. This system is implemented using a high speed 32-bit DSP (TMS320C31-50), a high-integrated logic device FPGA(EPF10K10TI144-3) to design compactly and inexpensively. The proposed scheme is verified by the results through digital simulation and experiments for a three-phase 13.3[kW] SMPMSM as a MRL(MachineRoomLess) elevator motor in the laboratory.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.8
• /
• pp.3617-3625
• /
• 2011

This paper introduces new concept elevator door system with linear induction motor(LIM) featuring simple structured and direct drive mechanism, which makes up for the weak points of the conventional complex structured door system. The optimal configuration of linear door system and the design results of linear LIM will be proposed in this paper and the validation of LIM design results will be investigated through the test. In this study, high performance of drive controller applied vector control and optimum drive pattern also are suggested. In addition, this paper describes details of designing and manufacturing process of linear door system and investigates the performance by analysis and test. The analytical and experimental results of this paper are considered as the productive data for the development of new elevator door system.

• Aerospace Engineering and Technology
• /
• v.5 no.2
• /
• pp.1-7
• /
• 2006

This paper presents a new point navigation guidance law which is useful for unmanned helicopters. Predicting the future position, the guidance law generates velocity and heading commands, which are used as input to autopilot. This method differs from conventional guidance law in that it reorients the direction of flight velocity vector directly, not by bank angle indirectly. For flight tests, we have developed a flight control system for a R/C helicopters. The system consists of a flight control computer, navigation sensors, and a ground station The results of the test show that the proposed law guides a unmanned helicopter along a line path within a given area. In the future, we are planning to extend the guidance law to the mission of path following. i.e., waypoint navigation.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.1
• /
• pp.33-45
• /
• 1997

Axisymmetric shear layers around a free jet is forced by co-flowing and counter-flowing secondary jets from/to an annular tube around the jet nozzle. The jet potential core extends far downstream with co-flowing secondary jets due to inhibited vortex developing and pairing. For counter-flowing cases, the axisymmetric shear layer around the jet transits from convective instability to absolute instability for velocity ratios R＝1.3～l.65 for the uniform velocity jets. Consequently, the jet potential core length increases and the turbulence level in the jet core is reduced significantly. The jets are controlled better with extension collars attached to the outer nozzle exit because the annular secondary flow is guided well by the extension collars. For the vectoring of jet, the annular tube around the jet is divided in two parts and the only one part is used for suction. The half suction makes the different shear layer around the jet and vectoring the jet by Coanda effect. The vectoring and turbulent components are varied significantly by the suction ratio. The experiments are carried out to investigate the characteristics of forced free jets using flow visualization, velocity and turbulence measurements.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2002-2004
• /
• 1998

In this paper, the compensation algorithm of the stator resistance which is essential to improving the performance of the direct vector control system is proposed. This paper focuses on the improvement in the torque response of the direct vector control in a constant speed region. The conventional compensation algorithms are analyzed and a new method is developed to compensate the stator resistance in the direct vector control system. In addition, the effect of the variation of the stator resistance on the drive performance is analyzed for the vector control. The proposed algorithm is very simple to implement that does not require the modifications on the motor model or additional interrupts of the controller. Also, the value of the stator resistance can be obtained in real-time through the measurement of the terminal voltage and current. From the simulation and experimental results, the validity of the proposed scheme is confirmed.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.5
• /
• pp.62-70
• /
• 2007

In this paper, the boost Power Factor Correction(PFC) technique for Direct Torque Control(DTC) of brushless DC motor drive in the constant torque region is implemented on a TMS320F2812DSP. Unlike conventional six-step PWM current control, by properly selecting the inverter voltage space vectors of the two-phase conduction mode from a simple look-up table at a predefined sampling time, the desired quasi-square wave current is obtained, therefore a much faster torque response is achieved compared to conventional current control. Furthermore, to eliminate the low-frequency torque oscillations caused by the non-ideal trapezoidal shape of the actual back-EMF waveform of the BLDC motor, a pre-stored back-EMF versus position look-up table is designed. The duty cycle of the boost converter is determined by a control algorithm based on the input voltage, output voltage which is the dc-link of the BLDC motor drive, and inductor current using average current control method with input voltage feed-forward compensation during each sampling period of the drive system. With the emergence of high-speed digital signal processors(DSPs), both PFC and simple DTC algorithms can be executed during a single sampling period of the BLDC motor drive. In the proposed method, since no PWM algorithm is required for DTC or BLDC motor drive, only one PWM output for the boost converter with 80 kHz switching frequency is used in a TMS320F2812 DSP. The validity and effectiveness of the proposed DTC of BLDC motor drive scheme with PFC are verified through the experimental results. The test results verify that the proposed PFC for DTC of BLDC motor drive improves power factor considerably from 0.77 to as close as 0.9997 with and without load conditions.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2008.10a
• /
• pp.65-72
• /
• 2008

Mobile Collaboration is an enabling technology that makes users share information between mobile devices and various Mobile P2P platforms have been designed and implemented for it. There are, however, few research papers on application of SIP protocol to spatial data sharing on mobile devices. In this paper, SIP based real time sharing framework is proposed to compose a mobile P2P platform on which spatial data can be trans(erred. A new protocol based on WKT and WKB is defined to send and receive spatial objects with SIP MESSAGE method. Base maps such as digital maps and parcel maps can be provided by a map server that is integrated with SIP server after a new SIP session established and client agents are registered. The framework proposed based onSIP enables users to transfer spatial data such as maps and satellite images directly between mobile devices during VoIP based voice call and therefore, mobile applications can be applied in various domains such asforest management and national defense.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.39 no.4
• /
• pp.347-357
• /
• 2003

This paper describes on the suppression of sea clutter on marine radar display using a cell-averaging CFAR(constant false alarm rate) technique, and on the analysis of radar echo signal data in relation to the estimation of ARPA functions and the detection of the shadow effect in clutter returns. The echo signal was measured using a X -band radar, that is located on the Pukyong National University, with a horizontal beamwidth of $$3.9^{\circ}$$, a vertical beamwidth of $20^{\circ}$, pulsewidth of $0.8 {\mu}s$ and a transmitted peak power of 4 ㎾ The suppression performance of sea clutter was investigated for the probability of false alarm between $l0-^0.25;and; 10^-1.0$. Also the performance of cell averaging CFAR was compared with that of ideal fixed threshold. The motion vectors and trajectory of ships was extracted and the shadow effect in clutter returns was analyzed. The results obtained are summarized as follows；1. The ARPA plotting results and motion vectors for acquired targets extracted by analyzing the echo signal data were displayed on the PC based radar system and the continuous trajectory of ships was tracked in real time. 2. To suppress the sea clutter under noisy environment, a cell averaging CFAR processor having total CFAR window of 47 samples(20+20 reference cells, 3+3 guard cells and the cell under test) was designed. On a particular data set acquired at Suyong Man, Busan, Korea, when the probability of false alarm applied to the designed cell averaging CFAR processor was 10$^{-0}$.75/ the suppression performance of radar clutter was significantly improved. The results obtained suggest that the designed cell averaging CFAR processor was very effective in uniform clutter environments. 3. It is concluded that the cell averaging CF AR may be able to give a considerable improvement in suppression performance of uniform sea clutter compared to the ideal fixed threshold. 4. The effective height of target, that was estimated by analyzing the shadow effect in clutter returns for a number of range bins behind the target as seen from the radar antenna, was approximately 1.2 m and the information for this height can be used to extract the shape parameter of tracked target..