• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.4
• /
• pp.57-61
• /
• 2007

We designed and fabricated square coils of 4 layered structure on a PCB board. The size of the coils were $1{\times}1cm^2\;and\;$2{\times}2cm^2$. The line width of the fabricated coils was $100{\mu}m$. By reciprocating a magnet on the surface of a fabricated square coil which is composed of 4 layers, an alternating output voltage was obtained. We changed the vibrational frequency from 0.5 to 7 Hz. The generated voltages were 62 mV at $1{\times}1cm^2$ and 245 mV at $2{\times}2cm^2$ when 5.5 Hz frequency. We rectified and stepped up the output voltage using a quadrupler circuit and $2{\times}2cm^2$ coil. Before using the step up circuit, the measured voltage was 320 mV at 7 Hz. After using the step up circuit, the measured voltage was 400 mV at 7 Hz.

• Journal of the Korea Convergence Society
• /
• v.7 no.5
• /
• pp.169-173
• /
• 2016

Anodic oxidation of aluminum has a sulfuric acid method and a oxalic acid method. Sulfuric acid concentration of the sulfuric acid method is 15~20 wt%. In the case of soft anodizing used in the $20{\sim}30^{\circ}C$ range, and voltage is the most used within a DC voltage 13~15V. In the case of hard anodizing used in the $0{\sim}-5^{\circ}C$ range. An aluminum oxide layer is made using sulfuric acid and oxalic acid. In this study, thermal fatigue of aluminum oxide layer which is made using sulfuric acid and oxalic acid is compared. Crack generating temperature of a sulfuric acid method and a oxalic acid method is $500^{\circ}C$ and $600^{\circ}C$. Thermal fatigue of aluminum oxide layer which is made using oxalic acid is better than thermal fatigue of aluminum oxide layer which is made using sulfuric acid. The characteristic of thermal fatigue can be explained by using thermal expansion coefficient of Al and Al2O3 and manufacturing temperature on Al anodizing. It was made possible through the convergent study to propose the manufacturing method of the anodic oxidation product used at a high temperature.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.1A
• /
• pp.93-98
• /
• 2004

Serial ATA interface Is inexpensive comparatively and performance is superior. So it is suitable technology in demand that now require data transmission and throughput of high speed. This paper describes a design and implementation of Serial ATA Link layer about error detection and 8b/10b encoder/decoder for DC balance in frequency 150MHz. The 8b/10b Encoder is partitioned into a 5b/6b plus a 3b/4b coder. The logical model of the block is described by using Verilog HDL at register transistor level and the verified HDL is synthesized using standard cell libraries. And it is fabricated with $0.35{\mu}m$ Standard CMOS Cell library and the chip size is about $1500{\mu}m\;*\;1500{\mu}m$. The function of this chip has been verified and tested using testboard with FPGA equipment and IDEC ATS2 test equipment. It is used to frequency of 100MHz in verification processes and supply voltage 3.3V. The result of testing is well on the system clock 100MHz. The designed and verified each blocks may be used IP in the field of high speed serial data communication.

• Korean Journal of Food Science and Technology
• /
• v.38 no.5
• /
• pp.712-716
• /
• 2006

Saccharomyces cerevisiae and Zygosaccharomyces rouxii were electrofused and fermented in germaniumfortified nutrients to produce high-yield, organic germanium. The conditions for the preparation of protoplasts from both strains and for electrofusion were studied. The protoplasts of both cells formed long pearl chains and the cell membranes were lysed and fused through cellulase and high frequency voltage $(450{\sim}750V/128{\sim}512\;{\mu}sec)$. The fusants with the fastest growth were selected, and then characterized for their carbohydrate usage and tolerance to glucose and salts. The glucose tolerance of the fusants was better than that of S. cerevisiae and similar to that of Z. rouxii. The fusants appeared to have resistance to 12% NaCl. The cell size of the fusants was greater than that of the parental strains. The fusant cells contained more gemlanium than the parental cells did. The electrofusion of S. cerevisiae and Z. rouxii increased the cell capacity and accumulation of germanium in the yeasts. This method was proved to be effective to produce a high quantity of organic germanium.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.4
• /
• pp.65-73
• /
• 2003

This paper presents the implementation of an analog signal-processing ASIS to detect an angular velocity signal from a vibrator angular velocity detection sensor. The output of the sensor to be charge appeared as the variation of the capacitance value in the structure of the sensor was detected using charge amplifiers and a self oscillation circuit for driving the sensor was implemented with a sinusoidal self oscillation circuit using the resonance characteristics of the sensor. Specially an automatic gain control circuit was utilized to prevent the deterioration of self-oscillation characteristics due to the external elements such as the characteristic variation of the sensor process and the temperature variation. The angular velocity signal, amplitude-mod)Hated in the operation characteristics of the sensor, was demodulated using a synchronous detection circuit. A switching multiplication circuit was used in the synchronous detection circuit to prevent the magnitude variation of detected signal caused by the amplitude variation of the carrier signal. The ASIC was designed and implemented using 0.5${\mu}{\textrm}{m}$ CMOS process. The chip size was 1.2mm x 1mm. In the experiment under the supply voltage of 3V, the ASIC consumed the supply current of 3.6mA and noise spectrum density from dc to 50Hz was in the range of -95 dBrms/√Hz and -100 dBrms/√Hz when the ASIC, coupled with the sensor, was in normal operation.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.3
• /
• pp.43-49
• /
• 2010

Direct printing technology is an attractive metallization method, which has become immerging as "Green technology" to the conventional photolithography, on account of low cost, simple process and environment-friendliness. In order to commercialize the printed electronics in industry, it is essential to evaluate the electrical properties of conductive circuits using direct printing technology. In this contribution, we focused on the electrical characteristics of inkjet-printed circuits. A Cu nanoink was inkjet-printed onto a Bisaleimide triazine(BT) substrate with parallel transmission line(PTL) and coplanar waveguide(CPW) type, then was sintered at $250^{\circ}C$ for 30 min. We calculated the resistivity of printed circuits through direct current resistance by the measurement of I-V curve: the resistivity was approximately 0.558 ${\mu}{\Omega}{\cdot}cm$ which is about 3.3 times that of bulk Cu. Cascade's probe system in the frequency range from 0 to 30 GHz were employed to measure the Scattering parameter(S-parameter) with or without a gap between the substrate and the probe station chuck. The result of measured S-parameter showed that all printed circuits had over 5 dB of return loss in the entire frequency range. In the curve of insertion loss, $S_{21}$, showed that the PTL type circuits had better transmission of radio frequency (RF) than CPW type.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.124-133
• /
• 2015

Electro interstitial scan shows potential as a non-invasive screening method. It can discriminate some diseases based on electric current response to induce low intensity direct current to limbs or local area of body. DDFAO was invented in France and it is claimed that multi-channel EIS(Electro Interstitial Scan) is useful for various diseases, especially, diagnoses of endocrine system such as diabetics are very effective. In this study, we verified the repeatability and sensitivity of DDFAO by using a RC phantom model and its clinical usefulness using data obtained from normal and diabetes subject groups. As a result, it showed the repeatability and the output change according to change of phantom characteristic, but it was hard to distinguish normal and patient groups non-invasively with just six surface electrodes of DDFAO. The repeatability and the clinical accuracy was not sufficient for screening or diagnostic purposes, as well. In spite of the results with low repeatability and accuracy conducted in this study, we still need further investigations to improve the EIS-based measurement method; EIS is very convenient and simple and it shows potential as a screening tool of the whole body health conditions rather than localized disease diagnosis.

• Journal of Navigation and Port Research
• /
• v.26 no.1
• /
• pp.22-27
• /
• 2002

The 25 Watt hybrid MIC SSPA has been developed in the frequency rang from 1.6265 GHz to 1.6465 GHz for uplink of INMARST's earth station. To simplify the fabrication process, the whole system is designed of two parts composed of a friving amplifier and a power amplifier. The Motorolas MRF-6401 is used for driving part, the Motorolas MRF-16006 and MRF-16030 is used the power amplifier. We reduced weight and volume of high power amplifier through arranging the bias circuits in the same housing. The realized SSPA has more than 30 dB for gain within 20 MHz bandwidth, and the voltage standing wave ratios(VSWR) of input and output port are less than 1.7, respectively. The output power of 44 dBm is achieved at the 1 dB gain compression point of 106365 GHz These results reveal a high power amplifier of 25 Watt which is the design target. The Proposed SSPA manufacture techniques in this paper can be applied to the implementation of high power amplifiers for some radars and SCPC.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.311-311
• /
• 2014

III-N계 물질로 이루어진 GaN 기반의 광 반도체는 직접 천이형 넓은 밴드갭 구조를 갖고 있기 때문에 적외선부터 가시광선 및 자외선까지를 포함한 폭 넓은 발광파장 조절이 가능하여 조명 및 디스플레이 관련 차세대 광원으로 많은 관심을 받고 있다. 하지만, GaN기반의 발광 다이오드는 많은 연구기관들의 오랜 연구에도 불구하고 고출력을 내는데 있어 여전히 많은 문제들이 존재한다. 그 중, 주입전류 증가에 따른 효율감소 현상은 출력을 저해하는 대표적인 요소로 알려져 있는데, 이전의 연구 결과에서 알려진 효율감소 현상의 원인으로 결정결함에 의한 누설전류, Auger 재결합, 이송자 넘침 현상 그리고 p-n접합부의 온도 상승 등의 현상이 알려져 있다 [1-2]. 하지만 여전히 주입 전류 증가에 따른 효율 감소 현상의 원인에 대해 명확한 해답은 없으며 아직도 많은 논의가 이루어 지고 있다. 따라서, 본 연구에서는 GaN기반의 청색 및 녹색 LD와 LED소자를 이용하여 주입전류 밀도의 변화에 따른 자발 발광 영역에서의 효율감소 현상의 원인을 규명하고 한다. 유기금속화학증착법(MOCVD)를 이용하여 c면 사파이어 위에 서로 다른 발광파장을 가지는 InGaN/GaN 다중양자우물구조의 질화물계 LED와 LD 박막을 제작하였으며 성장 구조에 의한 특성으로 인해 발생하는 효율 저하 현상을 방지하고자 InGaN/GaN으로 이루어진 다중양자우물층의 조성만 제어하여 청색과 녹색으로 발광하도록 하였다. 청색 및 녹색 LD 웨이퍼들을 이용하여 주입전류 증가에 따른 발광특성을 조사하기 위해 LD와 LED는 표준 팹 공정에 의해 제작되었다. 전계 발광 측정을 위해 상온에서 직류 전류를 주입하여 GaN계 청색 및 녹색 LED와 LD에 각 5 mA/cm2에서 50 mA/cm2까지 전류밀도를 증가시킴에 따라 LD 및 LED칩 형태에 상관없이 청색 LD와 LED의 파장은 약 465nm에서 약 458nm로 감소하였고 녹색 LD와 LED의 파장은 약 521nm에서 약 511~513 nm까지 단파장화가 발생했다. 이는 동일한 웨이퍼에 동일한 전류 밀도를 주입하였기 때문에 발생하는 것으로 판단된다. 그러나, 청색 LED의 효율은 50 mA/cm2에서 약 70%정도로 감소하고 반면 녹색 LED의 경우 동일한 전류밀도 하에 약 52%정도로 감소하였지만, 청색과 녹색 LD의 경우 동일한 전류 밀도의 범위 내에서 더욱 낮은 효율저하 현상을 나타내었다. 또한, 접합 온도를 측정한 바 청색소자가 녹색 소자에 비하여 낮은 접합 온도를 나타낼 뿐아니라, 청색 및 녹색 LD의 경우 LED 보다 낮은 접합 온도를 나타내고 있었다. 이는 InGaN 활성층의 In 조성이 증가할수록 비발광 센터에 의한 접합온도 상승 뿐 아니라, LD ridge 구조에서 더 많은 열이 방출되어 접합 온도가 감소될 수 있는 것으로 판단된다. 우리는 동일한 웨이퍼에 LED와 LD를 제작하였고, 동일한 전류 주입밀도를 인가하였기 때문에 LD와 LED의 효율 감소 현상의 차이는 이송자 넘침 현상, 결정 결함, 오제 재결합 등이 원인보다 활성층의 접합 온도 상승이 가장 큰 영향이 될 수 있을 것으로 판단된다.

• Polymer(Korea)
• /
• v.29 no.4
• /
• pp.363-367
• /
• 2005

The effects of organic solvent on the charge transport behavior of poly (3,4-ethylenedioxythioph one)/p-toluene-sulfonate(PEDOT-OTs) are investigated. The use of different organic solvents during the oxidative chemical polymerization of 3,4-ethylenedioxythiophene (EDOT) with Iron(III) -tosylate can greatly vary the DC conductivity of PEDOT-OTs along with molecular structure and doping concentration. For example, PEDOT-OTs prepared from methanol shows the conductivity of 19.5 S/cm, which is an increase by a factor of $10^8$ compared to PEDOT-OTa prepared from acetone. From the X-ray diffraction (XRD) experiments, it was found that PEDOT-OTs with ketone is amorphous state, while PEDOT-OTs with alcoholic solvent shows the better defined crystalline structure in which the charge transport along and between the PEDOT chains are promoted. Chemical analysis employing X-ray photoelectron spectroscopy (XPS) revealed that the doping concentration of PEDOT-OTs with alcoholic solvent is much higher than that of PEDOT-OTs with ketones. It is proposed that the interactions between the organic solvent and doping anion can cause the variation in doping concentration and, therefore, result in the PEDOT-OTs of different conductivities and chain structures.