• The Journal of Engineering Geology
• /
• v.17 no.1 s.50
• /
• pp.75-87
• /
• 2007

The recognitions of geometrical characteristics and occurrence conditions are very important to evaluate the land-slides in natural terrains. In this paper, the geometrical characteristics of landslides are analyzed according to a geo-logical condition in three landslides areas. The three landslides areas are classified to the geological condition. The three landslides areas are Jangheung, Sangju and Pohang. The geology of Jangheung area, Sangju area and Pohang area is gneiss, granite, and the tertiary sedimentary rock, respectively. During a heavy rainfall of $150{\sim}588mm$ in these areas, 1,582 landslides have occurred in 1998. The geometrical characteristics according to the geological condition analyzed from the investigation of these landslides. The frequency of landslide is high exceedingly above 90% of a slope attitude, while the frequency is very low below 70%. The frequency of landslide is high exceedingly between $26^{\circ}$ and $30^{\circ}$ of slope angle, while the frequency is very low below $20^{\circ}$. The size of the landslides is ranged from several tens to several hundreds The length is ranged from 5 m to 300 m, and the width is ranged from 3 m to 50 m. Also, the depth is less than 1 m. Therefore, the landslides in these areas have small width, long length and shallow depth. The type of the landslides is changed from transitional slide at the scarp to debris flow at the low part of slope.

• The Journal of Engineering Geology
• /
• v.18 no.1
• /
• pp.55-68
• /
• 2008

At present underground structures such as road tunnels, railway tunnels, underground petroleum storages and radioactive waste storages are being constructed in numerous places in Korea. For the construction of underground structrues, it should be accounted for natural factors (geology, hydrogeology, soil, vegetation, topography and drainage patterns) and human-social factors (land use, urbanization, population, culture and transportation). Especially, hydrogeology should be regarded as an important factor for evaluating the safety of underground structures and their impact to groundwater system around the structures. This study aimed to recognize hydrogeological characteristics of shallow formations in the area from Dongrae crossway to Seo-Dong where 45 boreholes were drilled for the construction of Line-3 subway in Busan Megacity. Slug tests for unsaturated and saturated zones were conducted on 30 boreholes in the study area. From the result of the slug tests, it was identified that average zonal hydraulic conductivity in the unsaturated zone was higher than that in the saturated zone. Besides, the slug test result in the saturated zones may reflect hydraulic properties of the upper most part of the saturated zones.

• The Journal of Engineering Geology
• /
• v.21 no.1
• /
• pp.57-64
• /
• 2011

Three-dimensional slope stability analysis was applied to a failed dual-lithology slope containing both granite and an andesitic dyke, taking account of the differences in shear strength of the different lithologies. A direct shear test of the soil-rock boundary was performed to examine the shear strength of two different types of failure surfaces within different lithologies, and a laboratory test was performed on an upper, weathered soil layer. The test results indicate that shear strength was lower at the soil-rock boundary than within the weathered soil layer. A representative geological section was subjected to two-dimensional slope stability analysis using a limit equilibrium method to assess whether the distribution of lithologies upon the slope influences the results of stability analysis. The results were then compared with those of three-dimensional slope stability analysis, for which input parameters can be varied according to the distribution of lithologies upon the slope. The three-dimensional analysis yielded safety factors of 1.26 under dry conditions and 0.55 under wet conditions, whereas the two-dimensional analysis yielded unstable safety factors of 0.92 and 0.32, respectively. These findings show that the results of stability analysis are affected by the distribution of different lithologies upon the slope. Given that the studied slope collapsed immediately after rainfall, it is likely that the results of the three-dimensional analysis are more reliable.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.4
• /
• pp.39-46
• /
• 2013

Recently, there have been various researches on the cost reduction and savings during the construction activities with the development of automation and computerized information system. Considering the cost savings during the construction, the development of the geological and geotechnical information system with high practical use becomes very important since the geologic and geotechnical data are required for the design of the various structures. Currently, the geological and geotechnical data are collected and distributed as a geological/geotechnical map or engineering geology map and map with other specific purpose through geoinfo system at Korea Institute of Geoscience and Mineral Resources, Korea Mineral Resources GIS at Korea Mineral Resources Corporation, Geotechnical Information Portal System at Korea Institute of Construction Technology, Geotechnical Information System at the City of Seoul and the Ocean Data Integration Material System at Korea Hydrographic and Oceanographic Administration. Furthermore, the information on the groundwater is monitored and collected via Integrated Ground Water Information Service at Korea Water Resources Corporation and Rural Groundwater net at Korea Rural Community Corporation. Therefore, in this study, the contents of the geological and geotechnical data collected from the above mentioned government organization are compared and the DB and distribution system with higher utilization are suggested based on the comparisons with those from other countries such as United States of America, Japan and Germany.

• The Journal of Engineering Geology
• /
• v.32 no.2
• /
• pp.209-219
• /
• 2022

To experimentally investigate the variation of soil characteristics in slope during rainfall and the shape of slope failure, the model test was performed using soil box and artificial rainfall simulator. The model test of slope formed by the homogenous sand was performed, and the saturation pattern in the model slope due to rainfall infiltration was observed. The slope model with the inclination of 35° was set up on the slope of 30°, and the rainfall intensity of 50 mm/hr was applied in the test. The soil depth of 35 cm was selected by considering the size of soil box, and the TDR (time domain reflectometry) sensors were installed at various depths to investigate the change of soil characteristics with time. As the result of model test, the slope model during rainfall was saturated from the soil surface to the subsurface, and from the toe part to the crest part due to rainfall infiltration. That is, the toe part of slope was firstly saturated by rainfall infiltration, and then due to continuous rainfall the saturation range was enlarged from the toe part to the crest part in the slope model. The failure of slope model was started at the toe part of slope and then enlarged to the crest part, which is called as the retrogressive failure. At the end of slope failure, the collapsed area increased rapidly. Also, the mode of slope failure was rotational. Meanwhile, the slope failure was occurred when the matric suction in the slope was reached to the air entry value (AEV) estimated in soil-water characteristic curve (SWCC).

• The Journal of Engineering Geology
• /
• v.33 no.3
• /
• pp.475-487
• /
• 2023

We surveyed the distribution of soil layers on Dongdo and Seodo of Dokdo and measured the physical properties of the soils. To investigate the distribution of soil layers, the soil depth was measured directly in accessible locations, and visual observations of inaccessible locations were carried out using drones and boats. Soil depths ranged from 3 to 50 cm, and most soil layers had depths of 10~20 cm. Based on these results, a map of the soil layer was drawn using 5 cm intervals for soil depth. To analyze the soil characteristics of Dokdo, soil samples were collected from 13 locations on Dongdo and 13 locations on Seodo, in consideration of various geological settings. According to the results of grain size distribution tests, sand contents were >75%, and soil from Seodo contained more gravel-sized particles than that from Dongdo. Using the unified soil classification system (USCS) and textural classification chart of the United States Department of Agriculture (USDA), most of the soil samples from Dokdo are classified as sand, and some are classified as loamy or clayey sand. In addition, well-graded loamy or clayey sands are more common in Dongdo, and poorly graded sands with gravel are more common in Seodo. These results are expected to be important for studying soil characteristics on Dokdo.

• The Journal of Engineering Geology
• /
• v.29 no.2
• /
• pp.137-151
• /
• 2019

Geophysical exploration techniques are effective for monitoring changes in the ground condition around the excavation project to prevent subsidence risks during excavation work, therefore, improving analysis techniques is required for applying and supplementing various geophysical exploration technologies. In this study, a field-scale on-site test was conducted to detect possible ground subsidence hazards and areas of relaxation zone that may occur during excavation work and due to underground water level changes. In order to carry out the field test, a real-scale excavation test bed was constructed and the geophysical exploration methods, such as electrical resistivity survey and multi-channel analysis of surface wave (MASW) survey for urban sites condition, have researched for optimal geophysical exploration parameter, design and correlation analysis between the results by reviewing the validity of each individual geophysical exploration and modeling. The results of this study showed the impact of each geophysical exploration on the relaxation zone and, in particular, the location of the underground water surface and the effects of excavation were identified using electrical resistivity survey. Further research on modeling will be required, taking into account the effects of excavation and groundwater.

• The Journal of Engineering Geology
• /
• v.28 no.4
• /
• pp.701-714
• /
• 2018

The purpose of this study is to show the possibility of 3-dimensional modeling of open-pit limestone mine by using a rotary-wing unmanned aerial vehicle, a drone, and to estimate the amount of mining before and after mining of limestone by explosive blasting. Analysis of the image duplication of the mine has shown that it is possible to achieve high image quality. Analysis of each axis error at the shooting position after analyzing the distortions through camera calibration was shown the allowable range. As a result of estimating the amount of mining before and after explosive blasting, it was possible to estimate the amount of mining of a wide range quickly and accurately in a relatively short time. In conclusion, it is considered that the drone of a rotary-wing unmanned aerial vehicle can be usefully used for the monitoring of open-pit limestone mines and the estimation of the amount of mining. Furthermore, it is expected that this method will be utilized for periodic monitoring of construction sites and road slopes as well as open-pit mines in the future.

• The Journal of Engineering Geology
• /
• v.32 no.4
• /
• pp.685-696
• /
• 2022

Although the use of pottery-making soils has a long history, its use in the pottery industry requires that physical and geotechnical properties of the materials be established to define the suitability for various purposes. The main purpose of this study is to identify the different types of clays and mineral composition and to perform the geotechnical evaluation of the clays for making pottery products. Soils investigated in this study include raw materials used for making Baekja (white porcelains), Chungja (celadons), Buncheong, Sancheong, and Johyung. Pottery-making soils are manufactured by using different types of soils and sold by individual ceramic clay company. This study includes physical tests of soil and chemical analysis of major elements using XRF and XRD instrumentation. Grain size distributions, mineralogical composition, and a range of plasticities of soils for making different types of potteries are presented. Correlations between specific type of pottery clays and geotechnical and mineralogical characteristics are determined by comparing the test results. Since quantitative research using laboratory tests for pottery-making soils are rarely performed in Korea, further research should be done in the future to improve the Korean pottery industry.

• The Journal of Engineering Geology
• /
• v.13 no.1
• /
• pp.67-82
• /
• 2003

Pumping test data obtained from five natural mineral-water producing companies (Siwon Saemmul, Daejeong Eumryo, Jain Guanguang, Cheongsu Eumryo and Hanju Sikpum) that are located within 1 km radius around Mockcheon area were analyzed. Theis(1935), Papadopulos-Cooper(1967), Hantush(1960, 1962), Hantush-Jacob(1955), Moench(1985), Neuman-Witherspoon(1969), Gringarten-Witherspoon(1969) and Gringarten-Ramey(1974) equations were applied to the pumping test analysis. The result of the pumping test analysis shows that wedge-typed confined aquifer model (Hantush, 1962) and leaky confined aquifer Case-1 model (Moench, 1985) were suitable for the study area. The models match well with geologic structure in the study area which controls aquifer by means of two major thrust faults having Nl8E and NS strikes, respectively.