• Journal of the Earthquake Engineering Society of Korea
• /
• v.16 no.4
• /
• pp.19-26
• /
• 2012

For a seismic design or performance evaluation of a structure, an experimental investigation on a scale model of the structure or numerical analysis based on the finite element model is considered. Regarding the numerical analysis, a three-dimensional finite element analysis is performed if a high accuracy of the results is required, while a sensitivity or fragility analysis which uses huge seismic ground motions leads to the use of a lumped-mass stick model. The conventional modeling technique to build the lumped-mass stick model calculates the amount of the lumped mass by considering the geometric shape of the structure, like a tributary area. However, the eigenvalues of the conventional model obtained through such a calculation are normally not the same as those of the actual structure. In order to overcome such a deficiency, in this study, a new lumped mass stick model is proposed. The model is named the "frequency adaptive-lumped-mass stick model." It provides the same eigenvalues and similar dynamic responses as the actual structure. A non-prismatic column is considered as an example, and its natural frequencies as well as the dynamic performance of the new lumped model are compared to those of the full-finite element model. To investigate the damping effect on the new model, 1% to 5% of the critical damping ratio is applied to the model and the corresponding results are also compared to those of the finite element model.

• Land and Housing Review
• /
• v.13 no.1
• /
• pp.141-150
• /
• 2022

Responding to the increasing demand for research on seismic resistance of structures triggered by a large-scale earthquake in Korea, the Ministry of the Interior and Safety revised the typical application of the existing seismic design standards with the national seismic performance target enhanced. Therefore, in this paper, the dam body of the aged Test-Bed and the penstock with fluid were modeled by the three-dimensional finite element method by introducing several variables. The current seismic design standard law confirmed the safety of the dam structure and penstock against seismic waves. As a result of the 3D finite element analysis, the stress change due to the water impact of the penstock was minimal, and it was confirmed that the effect of the hydraulic pressure was more significant than the water impact in the earthquake situation. When the hydrostatic pressure is in the form of SPH, it was analyzed that the motion of the fluid and the location of stress caused by the earthquake can be effectively represented, and it will be easier to analyze the weak part. As a result of the analysis, which considers penstock's corrosion, the degree of stress dispersion gets smaller because the penstock is embedded in the body. The stress result is minimal, less than 1% of the yield stress of the steel. In addition, although there is a possibility of micro-tensile cracks occurring in the inlet of the dam, it has not been shown to have a significant effect on the stress increa.

• Journal of Korean Society for Geospatial Information Science
• /
• v.15 no.4
• /
• pp.11-20
• /
• 2007

Most natural disasters in Korea are caused by meteorological natural phenomena, which include storms, heavy rains, heavy snow, hail, tidal waves, and earthquakes. Rainfall is the most frequent cause of disasters and accounts for about 80% of all disasters. Particularly in recent years, Korea has seen annual occurrences of natural disasters associated with landslides (slope and retaining wall collapse and burying) due to meteorological causes from the increasing intensity of heavy rains including local heavy rainfalls. In Korea, it is critical to analyze the characteristics of landslides according to rainfall characteristics and to take necessary and proper measures for them. This study assessed the possibility of landslides in the Gangwon region with a geographic information system by taking into account the inducer factors of landslides and the maximum continuous rainfall of each area. It also analyzed areas susceptible to landslides and checked the distribution of landslide-prone areas by considering the rainfall characteristics of those areas.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.16-16
• /
• 2018

최근 국가시설물에서는 집중호우 등으로 인한 대상 부지 내의 홍수 발생 시 주요시설물에 기능 마비가 발생할 수 있고, 궁극적으로는 대규모 사고로 이어질 수 있기 때문에 외부침수에 대비할 수 있는 위험도 분석이 필요하다. 대상 부지에서의 외부침수의 원인으로서는 LIP(Local Intensive Precipitation)에 의한 홍수 발생조건, 인근에 댐, 제방 등이 위치한 경우 이들 시설물의 붕괴에 따른 홍수류의 원전 유입, 지진해일/폭풍해일에 의한 바다로부터의 홍수 유입 등이 대표적인 예이다. 따라서 대상 부지 및 그 SOC시설물의 안전도를 높은 수준에서 관리하기 위해서는 극한홍수가 유입될 때 침수심, 침수유속, 침수시간, 침수강도 등의 재해도를 분석하여야하고, 이들 SOC시설물의 취약도 평가를 실시하고 재해도와 취약도를 결합한 연계분석을 통하여 위험도를 재평가하여야 한다. 본 연구에서는 기후변화 시나리오에 대해서 LIP(극한강우) 조건을 빈도별 분석하였고, 기후변화에 의한 가능최대강우량(PMP)의 재포락을 실시하고, 이를 확률강우조건과 비교 검토하였다. 대상부지에서의 RCP4.5와 RCP8.5 조건하에서 발생빈도-지속시간-극한강우량과의 상관도를 제시하였다. 지형분석의 고도화 및 수문분석을 통한 LIP를 이용한 극한 홍수량의 산정을 실시하였고, 수리분석에 의한 극한홍수조건의 침수해석을 실시하였다. 침수해석을 통한 수리변량(침수심, 침수강도, 침수지속시간 등)을 산정하였고, 침수해석결과에 주요지점별 발생빈도-지속시간-침수위의 관계를 재해도로 제시하였다. 본 연구 결과 집중호우 조건하에서 국가 주요시설물에서의 침수심, 침수강도 등에 대한 새로운 재해도 곡선을 산정함으로써 중요한 SOC시설물의 내수 설계, 홍수 방지기능 설계, 홍수 방지 대책 및 절차의 고도화 및 홍수 저감 기능 평가에 기준이 될 것으로 판단된다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.479-479
• /
• 2021

최근 기상이변으로 인한 자연재해 발생이 증가하고 있고, 그에 따라 도시의 재난 대응력 강화가 국내에서는 물론 국제적으로도 중요한 이슈가 되고 있다. 특히 쇠퇴지역은 재난재해 발생 시 인적·물적 피해가 일반 지역 보다 상대적으로 크며, 복구에도 많은 시간과 예산이 소요되므로 대응책 마련을 위한 도시재생지역의 정밀한 재난재해의 위험성 분석 기술이 필요하다. 이에 본 연구에서는 도시재생사업 대상지(311개)에 대한 재난재해 유형별 위험성 및 회복성을 종합적으로 분석하는 종합진단 기법을 개발하고, 이를 적용한 프로토타입 시스템을 개발하였다. 재난재해의 범위는 「재난 및 안전관리 기본법」을 준용하여 이에 도시재생사업 시행에 영향을 받아 재난재해 발생에 따른 위험정도가 변화할 가능성이 높은 자연재해 (폭우, 폭염, 폭설, 강풍, 지진)5종과 사회재난 (화재, 붕괴, 폭발) 3종 총 8종으로 정의하였다. 종합진단 기법은 기후변화에 관한 정부간 협의체(IPCC) 위험도 평가 방법을 준용하여 위험요소 (위해성·취약성·노출성)와 대비·대응요소 (회복성)로 구분하고, 전문가 자문회의를 거쳐 재난재해에 특히 취약한 쇠퇴지역의 특성을 반영할 수 있는 종합진단지수 산정식을 개발하였다. 또한 쇠퇴지역 재난재해 종합진단 시스템은 도시재생 업무를 수행하는 사용자가 신속히 정보를 분석하고 활용에 용이하도록 Web-GIS 기반으로 설계하였으며, 종합진단 기법에 의해 산정된 분석결과를 100m × 100m 격자 단위의 등급으로 가시화한다. 분석 결과는 지속적인 연구 개발을 통해 최적의 도시재생사업 의사결정 지원 서비스를 위한 기초 분석 자료로 연계하여 활용되며, 분석 DB는 클라우드 서비스 기반의 도시재생 데이터 플랫폼을 통해 공유된다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.3
• /
• pp.747-754
• /
• 2014

In spite of its usefulness for health monitoring of structures on steady external load, the statistical pattern recognition technology (SPRT), based on Mahalanobis distance theory (MDT), is not good enough for the health monitoring of structures on large variability external load like earthquake. Damage is usually determined by the difference between the average measured value of undamaged structure and the measure value of damaged one. So when external variability gets larger, the difference gets bigger along, which is thus easily mistaken for a damage. This paper aims to overcome the problem and develop an improved Mahalanobis distance theory (IMDT), that is, a SPRT with revised MDT in order to decrease external variability so that we will be able to continue to monitor the structure on uncertain external variability. This method is experimentally tested to see if it precisely evaluates the health of a cable-stayed bridge on each general random load and earthquake load. As a result, the IMDT is found to be valid in locating structural damage made by damaged cables by means of data from undamaged cables. So it is proved to be effectively applicable to the health monitoring of bridges on external load of variability.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.6
• /
• pp.523-530
• /
• 2017

In this study, a method of probabilistic evaluation of the performance point of the structure obtained by capacity spectrum method (CSM) is presented. The performance point of the 4-story and 1-bay steel structure was determined by using CSM according to ATC-40. In order to analyze whether the demand spectrums exceed the performance limit of the structure, the limit displacements are derived for the performance limit of the structure defined from the plastic deformation angle of the structural member. In addition, by selecting a total of 30 artificial seismic wave having the response spectrum similar to the design response spectrum, the fragility curves were derived by examining whether the response spectrum obtained from the artificial seismic wave were exceeded each performance limit according to the spectral acceleration. The maximum likelihood method was used to derive the fragility curve using observed excess probabilities. It has been confirmed that there exists a probability that the response acceleration value of the design response spectrum corresponding to each performance limit exceeds the performance limit. This method has a merit that the stochastic evaluation can be performed considering the uncertainty of the seismic waves with respect to the performance point of the structure, and the analysis time can be shortened because the incremental dynamic analysis (IDA) is not necessary.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.2
• /
• pp.67-76
• /
• 2023

In this study, in order to enhance the joint capacity between the existing reinforced concrete (R/C) frame and the reinforcement member, we proposed a novel concept of Internal Composite Seismic Strengthening Method (CSSM) for seismic retrofit of existing domestic medium-to-low-rise R/C buildings. The Internal CSSM rehabilitation system is a type of strength-enhancing reinforcement systems, to easily increase the ultimate horizontal shear capacity of R/C structures without seismic details in Korea, which show shear collapse mechanism. Two test specimens of full-size two-story R/C frame were fabricated based on an existing domestic R/C building without seismic details, and then retrofitted by using the proposed CSSM seismic system; therefore, one control test specimen and one test specimen reinforced with the CSSM system were used. Pseudo-dynamic testing was carried out to evaluate seismic strengthening effects, and the seismic response characteristics of the proposed system, in terms of the maximum shear force, response story drift, and seismic damage degree compared with the control specimen (R/C bare frame). Experiment results indicated that the proposed CSSM reinforcement system, internally installed to the existing R/C frame, effectively enhanced the horizontal shear force, resulting in reduced story drift of R/C buildings even under a massive earthquake.

• Journal of the Korea Concrete Institute
• /
• v.26 no.2
• /
• pp.135-142
• /
• 2014

In paper after the strong earthquake of recently the Korea neighborhood, the Korean government survey show that the 86% of school buildings in Korea are in potential damage risk and only 14% of them are designed as earthquake-resistance buildings. Earthquake Reinforcing projects of school have been a leading by the ministry of education, however their reinforcing methods done by not proved a engineering by experiment which results in uneconomical and uneffective rehabilitation for the future earthquake. An experimental and analytical study have been conducted for the shear reinforcing method of RC beam by axis and horizontal axis load using attaching composite beam. Based on the previous research, in this study, design examples are given to show the performance evaluation for the column reinforcing of old school buildings using nonlinear analysis is going to be conducted and strengthening method is going to be on the market after their performance is proved by the test.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.8
• /
• pp.37-49
• /
• 2018

Since the observation of ground motions in South Korea, liquefaction manifestation was the first to be observed in Pohang earthquake in 2017 with $M_L$ 5.4. Because liquefaction causes ground settlement and lateral spread damaging in-ground or super structures, various researchers have been analyzing the Pohang liquefaction case history to better understand and predict liquefaction consequence and to prevent future disasters. In prior research at the 2018 EESK conference, a map of Liquefaction Potential Index (LPI), indicating the severity of liquefaction, in Pohang was created and compared with damage observations. The LPI correlated well with the observations, but the severity categorized by LPI range was significantly higher than the actual observations in most regions. The prior LPI map was created evaluating ground motions using the simplified approach. In this research, we perform the effective site response analyses with porewater pressure generation model for the detailed evaluation of liquefaction on the liquefied sites in Pohang. We found that the simplified approach for LPI evaluation can overestimate the severity.