• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.2 no.4
• /
• pp.17-27
• /
• 2003

This paper presents the channel estimation method with STBC applied to IEEE802.11a. Tenacious channel estimation method for OFDM system, that generally uses STTC, has been presented once and massive amount of calculation was needed However, regarding this paper, the amount of calculation can be reduced by using Curve Fitting, and channel tracking performance improvement can be achieved Based on the estimation method, computer simulation was done for the performance analysis and delay spread Doppler frequency and many other group sizes and numbers were considered As a result of the testing, we found out that Doppler frequency deviation effects equally as frequency offset. Also compared to the existing technique, channel estimated performance confirmed that have 0.9dB SNR improvement than old method.

• Journal of Sensor Science and Technology
• /
• v.8 no.1
• /
• pp.16-23
• /
• 1999

When a moving piezoelectric transducer detects an object in water, its receiving sensitivity is attenuated by Doppler effect. In this paper, a method for compensating the effect is suggested by using a newly designed condenser of which capacitance is varied according to the moving speed of the transducer. Using the method, the receiving resonant frequency of the transducer can be changed automatically. As a result, there is good agreement between the results of experiment and those of calculation. It is confirmed that the response sensitivity degradation of transducers due to Doppler effect can be compensated in the range of $1{\sim}10^m/_s$ moving speed.

• Korean Journal of Optics and Photonics
• /
• v.11 no.4
• /
• pp.250-254
• /
• 2000

We have constructed laser Doppler velocimetry system using self-mixing effect with a semiconductor laser. This technology is based on the frequency mixing phenomena which occurs when light scattered back from the moving object into the laser cavity interferes with light inside the laser. We have compared the value of Doppler shifted frequency with the velocity variation of the wheel. Frequency dependence on the angle between the moving direction of rotating aluminum wheel and the incident beam also have been proved. As an illustration of the performance of the velocimeter, velocity measurements of a rotating disk are described. Doppler signal shows a good linear relationship with velocity of rotating disk.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.3
• /
• pp.212-217
• /
• 2016

The S-band receiver for Low Earth Orbit satellite is designed and fabricated as engineering model. Demodulator is implemented by using FPGA for extension of demodulator method. The receiver consists of RF Block, Digital demodulator and Power stage and has a Doppler tracking function to compensate a frequency shift that occur on the operation. The measured results of fabricated receiver show BER of less than $1.0{\times}10^{-6}$ at -110dBm RF input power and equipped a frequency tracking of ${\pm}100KHz$ relative to the center frequency. TID test was satisfied with the results of the test criterion is 10krad.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.7
• /
• pp.815-821
• /
• 2012

A CW Doppler radar can measure radial velocity of an object. It detects a Doppler frequency shift that is proportioned to radial velocity of a moving object. To detect a Doppler frequency shift, FFT(Fast Fourier Transform) is conducted. In this process, the time domain received signal is transformed to a frequency domain. A number of FFT affects not only the time resolution but also signal to noise ratio of received signal. So finally it is related with a radial velocity accuracy. Therefore in this paper, it is described the relation of time resolution and the radial velocity accuracy.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.562-569
• /
• 2012

The rubber side could be contaminated using the existing pulse echo method because the ultrasonic wave was incident on the rubber side from the interior of the steel motor case, which could lead to the critical disbond defect. To develop the test method which can be replaced the existing method, the ultrasonic wave was incident on steel face of the steel/rubber adhesive test block. Rubber resonance frequencies measured from the steel/rubber adhesive test block were in good agreement with theoretically predicted rubber resonance frequencies. This paper was described about the ultrasonic resonance method to convert the rubber resonance frequency into the rubber thickness.

• Proceedings of the Optical Society of Korea Conference
• /
• 2002.07a
• /
• pp.18-19
• /
• 2002

1950년 Norman Ramsy는 시간적으로 분리된 두 진동 자장을 사용한 마이크로파 전이 방법을 개발했다 이 방법을 사용할 경우 그림1과 같이 넓은 선폭을 가지는 공진선 ("Rabi pedestal") 위에 좁은 선폭의 분광 신호("Ramsey fringe")를 얻을 수 있다. 램지 방법은 정밀한 분광 측정에 많이 사용되고 있으며, 특히 원자 시계를 구현하기 위한 기본 기술이 되고 있다. (중략)

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.11
• /
• pp.1070-1077
• /
• 2011

This paper introduces a radar signal processing technique for intelligent rear view monitoring of an automobile. The linear frequency modulation-frequency shift keying(LFM-FSK) waveform, which is the combination of frequency modulation continuous wave(FMCW) and frequency shift keying(FSK) waveform, is employed to simultaneously estimate the range, relative aspect angle, and velocity of an automobile. Hence, it can be applied to monitor the rear view of an automobile. FMCW waveform has high range resolution capability, but it produces ghost targets under a multiple target environment. In contrast, FSK waveform can provide high velocity resolution and avoids the problem of ghost targets. However, it fails to identify multiple targets along the radar's line of sight. With LFM-FSK waveform, we can estimate the ranges and velocities of multiple targets with very high resolution, which avoids the ghost target problem of an FMCW waveform. Simulation result shows that LFM-FSK wavefrom is suitable for use in the lane change assistance system for an automobile.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.511-517
• /
• 2015

Sound absorption capability of the flame resistant treated sawdust-mandarin peel composite particleboard was were estimated by two microphone transfer function methods. The weight of flame resistant treated board slightly increased by the treatment. The treatment improved fire retardant performance by decreasing the charred area of flame resistant treated board. Sound absorption capabilities of flame resistant treated sawdust-mandarin peel composite particleboard, in the entire estimated frequency range of 500-6,400 Hz was slightly lower than those of the control specimen. Sound absorption capability of both the control and flame resistant treated sawdust-mandarin peel composite particleboards were higher than that of commercial gypsum boards, being widely used as a sound absorber for ceiling at the estimated frequency.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.3
• /
• pp.528-535
• /
• 2011

In this paper, a compact doppler sensor with oscillator type active antenna operating at 2.4GHz frequency band is proposed to measure the distance to a moving object. The oscillation frequency is shifted depending on approaching of the object, and a detection circuit discriminates the frequency deviation. The active antenna has been designed and simulated. The prototype fabricated has a small circular disk type of diameter 30mm and height 4.2mm. As for antenna performance, broadside radiation pattern with beamwidth of $120^{\circ}$ and oscillation frequency of 2.35GHz has been measured. Test results as a range sensor shows that signal voltage of about 240mV has been obtained for conducting plate moving 1 meter away from the sensor. And, signal voltage has been linearly increased to the ground from 5m height by free-falling the sensor.