• Journal of the KSME
• /
• v.24 no.6
• /
• pp.446-451
• /
• 1984

최근 기계구조물로부터 발생되는 소음. 진동의 수준을 평가하고 그 대책을 수립하는데 스펙트 럼분석(spectral analysis)과 상관기술(correlation technique)의 이용도가 점증하고 있다. 전자계 산기에 의한 데이터처리기술의 진보에 따라 불규칙한 입력을 받는 기계구조물의 고유진동수추정 및 진동모우드해석, 많은 소음. 진동원을 갖는 플랜트. 선박. 차량기기등의 발생원검출 및 기여 량파악, 그리고 acoustic emission 및 bispectrum에 의한 기기이상진단기술에 적용함으로써 공 학분야에서 한층 중요한 위치를 점하고 있다. 따라서 본 강좌에서는 먼저 상관해석에 의한 스 펙트럼의 정의에 대해서 기술하고 샘플링이론에 만족하는 시간간격으로 샘플링함으로써 얻어지는 시계열데이타를 Fourier 변환하여 주파수영역에서 계의 특성을 해석하는 원리 및 기여함수에 대해 설명하고자 한다. 그리고 입력원간에 상관이 존재하는 경우에 있어서 소음. 진동원을 검 출하고 기여량을 추정할 수 있는 방법으로서의 다차원스펙트럼해석법에 대해 간단하게 기술하 고자 한다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.8
• /
• pp.1193-1198
• /
• 2012

An instantaneous amplitude (IA) estimator using the symmetric higher order differential energy operator is proposed. The amplitude estimator and the instantaneous frequency (IF) estimator based on the symmetric higher order differential energy operator coincide with the analyzed signal in time, and they show better estimation results than the IA and IF based on the higher order differential energy operator. Various IF and IA estimators are applied to AM-FM signals for the performance comparison. Among the IF and IA estimators, the IF and IA estimators based on the symmetric higher order energy operator show the best estimation accuracy. Then, the IA and IF estimators are applied to the distorted power line signal to show their usefulness as power disturbance detectors.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.369-372
• /
• 2003

This paper describes a design of OFDM (Orthogoanl Frequency Division Multiplexing) based wireless LAN system receiver, defined in IEEE 802.11a standards. Because OFDM system uses several orthogonal sequence sets, it ran avoid selective fading of fast data transfer problem when it is used with error correction code. But if the receiver is not synchronized, the orthogonal of between sub-ralliers will be destroyed and the data interruption will be generated. So it makes error property get worse very murk. For improving the noise error, we use the relationship of phasor between sub-carriers and make system synchronization using one tab equalizer. The designed OFDM block is described by Verilog HDL for the efficient and small size hardware. And we preform the functional verification and evaluation using the vector of standards.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.3A
• /
• pp.196-204
• /
• 2002

The Sinusoidal Transform Coding(STC) is a vocoding scheme based on a sinusoidal model of a speech signal. The low bit-rate speech coding based on sinusoidal model is a method that models and synthesizes speech with fundamental frequency and its harmonic elements, spectral envelope and phase in the frequency region. In this paper, we propose the 2.4kbps low-rate speech coding algorithm using the sinusoidal model of a speech signal. In the proposed coder, the pitch frequency is estimated by choosing the frequency that makes least mean squared error between synthetic speech with all spectrum peaks and speech synthesized with chosen frequency and its harmonics. The spectral envelope is estimated using SEEVOC(Spectral Envelope Estimation VOCoder) algorithm and the discrete all-pole model. The phase information is obtained using the time of pitch pulse occurrence, i.e., the onset time, as well as the phase of the vocal tract system. Experimental results show that the synthetic speech preserves both the formant and phase information of the original speech very well. The performance of the coder has been evaluated in terms of the MOS test based on informal listening tests, and it achieved over the MOS score of 3.1.

• The Journal of the Acoustical Society of Korea
• /
• v.27 no.7
• /
• pp.350-356
• /
• 2008

In this paper, we propose shading functions to the appropriate focused beamforming for near-field target estimation. This near field shading functions are based on Chebychev and Manning windows. In order to obtain the optimum sensor weighting values with the help of the proposed shading technique, we assume that the sensor positions associated to the non-uniformly distributed array are precisely known. We calculate a series of sensor weighting values from the FFT operation of given shading functions in time domain. By applying the shading weights on the sensor array, we can see that the level of sidelobe becomes diminished and the performance of estimating range and azimuth gets improved. In addition, we propose a non-uniform structure in terms of frequency bands, which may minimize the attenuation of incoming signals.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.3
• /
• pp.196-213
• /
• 2001

A split beam ultrasonic transducer operating at a frequency of 70 kHz to use in the fish sizing echo sounder was developed and the acoustic radiation characteristics were experimentally analyzed. The amplitude shading method utilizing the properties of the Chebyshev polynomials was used to obtain side lobe levels below -20 dB and to optimize the relationship between main beam width and side lobe level of the transducer, and the amplitude shading coefficient to each of the elements was achieved by changing the amplitude contribution of elements with 4 weighting transformers embodied in the planar array transducer assembly. The planar array split beam transducer assembly was composed of 36 piezoelectric ceramics (NEPEC N-21, Tokin) of rod type of 10 mm in diameter and 18.7 mm in length of 70 kHz arranged in the rectangular configuration, and the 4 electrical inputs were supplied to the beamformer. A series of impedance measurements were conducted to check the uniformity of the individual quadrants, and also in the configurations of reception and transmission, resonant frequency, and the transmitting and receiving characteristics were measured in the water tank and analyzed, respectively. The results obtained are summarized as follows : 1. Average resonant and antiresonant frequencies of electrical impedance for four quadrants of the split beam transducer in water were 69.8 kHz and 83.0 kHz, respectively. Average electrical impedance for each individual transducer quadrant was 49.2$\Omega$ at resonant frequency and 704.7$\Omega$ at antiresonant frequency. 2. The resonance peak in the transmitting voltage response (TVR) for four quadrants of the split beam transducer was observed all at 70.0 kHz and the value of TVR was all about 165.5 dB re 1 $\mu$Pa/V at 1 m at 70.0 kHz with bandwidth of 10.0 kHz between -3 dB down points. The resonance peak in the receiving sensitivity (SRT) for four combined quadrants (quad LU+LL, quad RU+RL, quad LU+RU, quad LL+RL) of the split beam transducer was observed all at 75.0 kHz and the value of SRT was all about -177.7 dB re 1 V/$\mu$Pa at 75.0 kHz with bandwidth of 10.0 kHz between -3 dB down points. The sum beam transmitting voltage response and receiving senstivity was 175.0 dB re 1$\mu$Pa/V at 1 m at 75.0 kHz with bandwidth of 10.0 kHz, respectively. 3. The sum beam of split beam transducer was approximately circular with a half beam angle of $9.0^\circ$ at -3 dB points all in both axis of the horizontal plane and the vertical plane. The first measured side lobe levels for the sum beam of split beam transducer were -19.7 dB at $22^\circ$ and -19.4 dB at $-26^\circ$ in the horizontal plane, respectively and -20.1 dB at $22^\circ$ and -22.0 dB at $-26^\circ$ in the vertical plane, respectively. 4. The developed split beam transducer was tested to estimate the angular position of the target in the beam through split beam phase measurements, and the beam pattern loss for target strength corrections was measured and analyzed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.11-12
• /
• 2010

PSC girder with holed web have several benefits. Most of all placing tendon anchorage in the holes can make prestressing forces be loaded stepwise. In addition it can reduce the self-weight of the beams and increase the span length of beams. And holed web might minimize the interference of view. In this study, a 50-meter long full scale multilevel post-tensioned PSC girder was fabricated and modal test was carried out. In order to obtain precise frequency response, vibration exciter was placed at the middle of the girder and excited with several frequencies. Natural frequency and damping ratio were evaluated from FFT and PSD using the obtained frequency response and compared with numerical analysis result.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.2
• /
• pp.66-72
• /
• 2009

In this paper, an efficient frequency offset synchronization structure for OFDM(Orthogonal Frequency Division Multiplexing) is proposed. Conventional CORDIC(Coordinate Rotation Digital Computer) algorithm for frequency offset synchronization utilizes two CORDIC hardware i.e., one is vector mode for phase estimation, the other is rotation mode for compensation. But proposed structure utilizes one CORDIC hardware and divider. Through simulation, it is shown that hardware implementation complexity is reduced compared with conventional structures. The Verilog-HDL coding and front-end chip implementation results for the proposed structure show 22.1% gate count reduction comparison with those of the conventional structure.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.45 no.5
• /
• pp.118-125
• /
• 2008

In this paper, an efficient frequency offset synchronization structure for OFDM(Orthogonal Frequency Division Multiplexing) is proposed. Conventional CORDIC(Coordinate Rotation Digital Computer) algorithm for frequency offset synchronization utilizes two CORDIC hardware i.e., one is vector mode for phase estimation, the other is rotation mode for compensation. But proposed structure utilizes one CORDIC hardware and divider. Through simulation, it is shown that hardware implementation complexity is reduced compared with conventional structures. The Verilog-HDL coding and front-end chip implementation results for the proposed structure show 22.1% gate count reduction comparison with those of the conventional structure.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1880-1881
• /
• 2007

전력선 통신 채널에는 특징적으로 충격 잡음이 존재하며, 전력선 통신 시스템의 성능 열화에도 많은 영향을 준다. 이는 일반적인 배경 잡음에 비해 많게는 수십 dB 이상의 레벨을 가지면서, 임의 시간적으로 발생함으로써 추정 및 제어 또한 어렵기 때문이며, 전력선 통신 시스템이 Mbps급으로 고속화 되면서 주파수 대역이 확장되고, 확장된 대역상에 다중 반송파를 이용하여 대용량의 데이터를 전송하는 변복조기법들이 적용됨에 따라, 시간 영역에서 비교적 짧은 시간 동안 존재하는 충격 잡음이 주파수 영역에서 사용 주파수 전체 대역상에 영향을 줌으로써 시스템 전체 성능 저하의 큰 요인이 되고 있다. 본 논문에서는 이러한 충격 잡음이 고속 전력선 통신 시스템에서 사용되는 OFDM(또는 DMT) 방식 수신기의 복조기 출력단 SNR에 미치는 영향을 분석 및 단순화하고, 시뮬레이션을 통해 검증한다.