• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.11
• /
• pp.1172-1182
• /
• 2014

In these days, many kinds of goods are more light and more integrated. As frequency range of mobile applications have increased to improve performance of antenna furthermore, EMI(ElectroMagnetic Interference) problem has frequently caused by disturbance of antenna in device which aggravates other circuit. This paper proposes a technique for the prediction of noise power to the transmission line from antenna located near the line. Although noise power transferred to transmission line is varied by source impedance of antenna and load impedance of transmission line basically, the power magnitude can be presented in a square form of S-parameter between antenna and transmission line due to small variation of transferred power. For this reason, we can use the index expressed the transferred power varied along geometrical shapes of transmission line. As a result, big difference is occurred along location of antenna especially the bended line. And this such experiment is correspond with simulation, these results have meaning physically considering electromagnetic field distribution in near and far field. HFSS of Ansys and CPW with ground is used in this paper.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.4
• /
• pp.108-116
• /
• 2002

This paper presents the measurements and evaluation of voltage waveforms due to human electrostatic discharge(ESD). The principle of operation and design rule of a new device for measuring the ESD fast transient voltages with very fast rise time were described. Peak values and rise time of ESD voltages derived from a charged human body under a variety of experimental conditions were examined. The frequency bandwidth of the proposed voltage measuring system ranges from DC to 400[㎒]. The ESD voltage waveform is nearly equal to the ESD current waveform and the peak amplitude of ESD current waveform is roughly proportional to the ESD voltage in each experimental conditions. A rapid approach results in a discharge voltage with a faster initial rise time than for a slow approach. The voltages caused by direct finger ESDs have an initial slope with a relatively long, 10∼30[ns] rise time, but the amplitude is small. On the other hand, the voltages caused by direct hand/metal ESDs have a steep initial s1ope with 1 ∼3[ns] rise time, but an initial spike is very big. As a consequence, it was found that the ESD voltage and current waveforms strongly depend on the approach speed and material of intruder. These measurement results would be useful to design the ESD protective devices.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.233-236
• /
• 2001

일반적으로 스피커를 동작시키게 되면, 스피커 보이스 코일에 열이 발생하게 되고, 열에 의한 보이스코일의 저항의 증가가 나타나게 되는데, 기존의 연구는 저음용 스피커(Woofer) 만을 대상으로 스피커의 음향특성 변화들에 관해 수행되었다. 그러나, 현대의 스피커는 A/V시스템분야의 발전에 따라 고음재생의 충실도가 강조되고 있는 경향이므로, 고음용 스피커(Tweeter)에 대한 열 발생의 영향을 조사하였다. 본 연구에서는 고음용 스피커의 입력전력에 따른 특성 변화를 조사하고, 입력전력의 증가로 인한 보이스코일(voice coil)의 저항 증가에 따른 고음용 스피커의 특성변화에 관해 실험하였다. 그리고, 스피커의 진동에 의한 펌프(pump) 역할을 이용하는 냉각용 구멍을 뚫어 스피커의 특성변화를 검토하였다. 실험대상으로는 직경 25mm의 돔(Dome)형 진동판을 가진 고음용 스피커와 이 스피커의 후면 중심부에 구멍을 뚫어 열 방출구가 형성된 3종의 시료를 대상으로 특성변화를 비교$\cdot$측정하였다. 여기에서, 사용된 시료는 국내 Y사의 판매용 고음용 스피커로 제품의 원 상태인, 구멍이 없는 것을 기준시료로 하고, 이와 동일한 제품들의 후면에 각각 직경 5mm, 10mm, 15mm의 구멍을 가공하여 비교시료로 하였다. 기준 및 비교시료의 스피커 특성을, 한국산업규격 KS C 6027의 측정법에 따라, 입력 1W 상태에서 기준시료의 사양을 측정하였고[1], 입력을 0.5W, 1W, 2W, 4W, 8W, 16W로 가하여, 시료별 입력증가에 따른 스피커의 주파수 응답특성, 임피던스(Impedance), 조화 왜(Harmonic Distortion)의 변화율 측정을 통해 스피커의 특성변화 정도를 검토하였다. 향후, 본 연구의 결과는 고음용 스피커의 특성 열화에 대한 예측 및 개선 방안을 제시하는 기본 자료로 활용이 가능할 것으로 사료된다.용하여 현금흐름예측을 할 수 있는 Model을 제시하였다. 특히 건설공사의 현금흐름 예측의 중요한 요소인 Cash-Out에 대하여, 공사비 구성요소인 자재, 노무, 중기, 외주, 경비등 각 Resource의 보할(Weights)을 실 공사원가에 따른 보할의 변화와 Resource들의 Time Lag를 적용 기존 연구자의 Model과 다른 Model을 제시하였다. 또한 기존 연구자들의 Model과 비교하여 편리성, 정확도 및 신뢰성이 높은 Model임도 증명하였다.세대까지도 발현수준이 유지될 것으로 판단된다. 이러한 연구결과는 계통으로 확립된 형질전환 동물에 부여된 새로운 유전형질은 지속적으로 후대로 유전될 수 있음을 제시한다.잖⨀瘀Ā퀇Āゑ잖⨀Ā퀇Ԁ￿™잖⨀䌀Ā퀇ĀꄏĀꀏꄏĀꀏ₱?⨀Ā Ԁ￿䂱?⨀ऀĀ耀Ā삱?⨀؀Ā Ā?⨀ጀĀ耀Ā?돀ꢘ?⨀硩?⨀ႎ?⨀?⨀넆돐쁖잖⨀쁖잖⨀／ࠐ?⨀焆덐瀆倆Āⶇ퍟ⶇ퍟ĀĀĀĀ磀鲕좗?⨀肤?⨀⁅Ⴅ?⨀쀃잖⨀䣙熸ጁ↏?⨀

• The Journal of Society for e-Business Studies
• /
• v.18 no.2
• /
• pp.223-240
• /
• 2013

RFID(Radio Frequency Identification) is use of an RFID tag applied to object for the purpose of identification and tracking using radio waves. Recently, it is being actively researched and introduced in logistics and manufacturing. RFID portals in supply chains are meant to identify all the tags within a given interrogation zone. Hence the hardware and software mechanisms for RFID tag identification mostly focus on successful read of multiple tags simultaneously. Such mechanisms, however, are inefficient for determining moving direction of tags, sequence of consecutive tags, and validity of the tag reads from the viewpoint of workflow. These types of problems usually cause many difficulties in RFID portal implementation in manufacturing environment, there by having RFID-system developers waste a considerable amount of time. In this research, we designated an RFID portal system with SDO(Sequence, Direction, and Object-flow)-perception capability by using fundamental data supplied by ordinary RFID readers. Using our work, RFID system developers can save a great amount of time building RFID data-capturing applications in manufacturing environment.

• Journal of Broadcast Engineering
• /
• v.15 no.3
• /
• pp.407-413
• /
• 2010

In DCA (Dynamic Channel Allocation) scheme of uplink cellular system appling a frequency reuse factor of one, when a new call requests a channel, the new call will be blocked if its SINR (Carrier to Noise and Interference Ratio) is less than the required SINR or there is no available channel. The additional channel allocation for the blocked new call can be performed with channel borrowing in the adjacent cells. The channel borrowing causes the CCI (Co-Channel Interference), thus the SINR of the existing calls is deteriorated and the channel reallocation for the existing calls is required. As a result, the channel borrowing leads to a complex calculation so that it is a NP-hard problem. Therefore, to overcome the problem, we propose a novel Group Search-based DCA scheme which decreases the number of the blocked new calls and then reduces the number of the channel reallocation by the channel borrowing for the blocked new calls. The proposed scheme searches the all channels in a group of the adjacent cells and home cell at the same time in order to minimizes the number of the blocked new calls. The simulation results show that proposed Group Search-based DCA scheme provides better new call blocking probability and system throughput than the existing Single Search-based DCA scheme which searches only the channels in home cell.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.2
• /
• pp.712-718
• /
• 2016

A heat exchanger tube array in a heat recovery steam generator is exposed to hot exhaust gas flow that can cause flow induced vibrations, which could damage the heat exchanger tube array. The characteristics of flow induced vibration in the tube array need to be established for the structural safe operation of a heat exchanger. Several studies of the flow induced vibrations of typical heat exchangers have been conducted and the nondimensional PSD (Power Spectral Density) function with the Strouhal number, fD/U, had been derived using an experimental method. The present study examined the results of the previous experimental research on the nondimensional PSD characteristics by CFD analysis and the basis for the application of flow induced vibration to the heat recovery steam generator tube array was determined from the present CFD analysis. The present CFD analysis introduced circular cylinder tube array and calculated using unsteady laminar flow for the tube array. The characteristics of lift and drag fluctuations over the cylinder tube array was investigated. The derived nondimensional lift and drag PSD was compared with the results of the previous experimental research and the characteristics of lift and drag PSD for a circular cylinder tube array was established from the present CFD study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.10
• /
• pp.6641-6646
• /
• 2015

Heat exchanger tube array in a heat recovery steam generator is exposed to the hot exhaust gas flow and it could cause the flow induced vibration, which could damage the heat exchanger tube array. It is needed to establish the characteristics of flow induced vibration in the tube array for the structural safe operation of the heat exchanger. Several researches for the flow induced vibration of typical heat exchangers had been conducted and the nondimensional PSD(Power Spectral Density) function with the Strouhal number, fD/U, had been derived by experimental method. The present study examined the results of the previous experimental researches for the nondimensional PSD characteristics by CFD analysis and the basis for the application of flow induced vibration to the heat recovery steam generator tube array would be prepared from the present CFD analysis. For the previous mentioned purpose, the present CFD analysis introduced circular cylinder tube array and calculated with the unsteady laminar flow for the tube array. The characteristics of lift fluctuation over the cylinder tube array was investigated. The derived nondimensional PSD was compared with the results of the previous experimental researches and the characteristics of lift PSD for circular cylinder tube array was established from the present CFD study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.797-803
• /
• 2019

This study was carried out to reduce the lateral vibration of high-speed electric multiple units. In the study, the high-speed electric multiple unit prototype (HEMU-430X) has a high lateral vibration at low equivalent conicity regardless of the wheel profiles (XP55, GV40, S1002). As wheel wear progresses and the equivalent conicity increases, the lateral vibration tends to decrease. The reason is that a combination of the suspension characteristics causes the body and bogie to resonate at a frequency of 1.4 Hz when the equivalent conicity is low, resulting in body hunting. An investigation of the lateral vibration of overseas high-speed trains showed that a decrease in the hydraulic stiffness of the yaw damper could improve the vibration. The series stiffness of the yaw damper is a combination of the hydraulic stiffness and elastic joint. In this study, an attempt was made to improve the lateral vibration by lowering the stiffness of the elastic joint. The series stiffness of the adjusted yaw damper was approximately 60% compared to the original one. The on track test results showed improvement in the lateral vibration for both running directions. The vibration reduction method of this study can be used for EMU-250 and EMU-320 in future commercial operations.

• Journal of Biomedical Engineering Research
• /
• v.23 no.2
• /
• pp.109-117
• /
• 2002

Electrogastrography(EGG) is a noninvasive method for measuring gastric electrical activity on the abdomen resulting from gastric muscle. EGG signals have a very low frequency range (0.0083 ~0.15 Hz) and extremely low amplitude(10~100 uV). Consequently, EGG signal is easily influenced by other noises. Both finite impulse response(FIR) and infinite impulse response (IIR) filters need high orders or have phase distortions for passing very narrow bandwidth of the EGG signal. In this study, we decomposed EGG signals using a wavelet multiresolution method with Daubechies mother wavelet. The EGG signals were decomposed to seven levels. We reconstructed signal by summing the decomposed signals from level four to seven. To evaluate the performance of the wavelet multiresolution filter(WMF) with simulated EGG signal using two kinds of FIR and four kinds of IIR filters., we used two indices; signal to noise ratio(SNR) and reconstruction squared error(RSE). The SNR of WMF had 9.5, 6.9, and 4.7 dB bigger than that of the other filters at different noise levels, respectively. Also, The RSE of WMF had $1.22{\times}10^6, 1.16{\times}10^6, 1.02{\times}10^6$ smaller than that of the other filters at different noise levels, respectively. The WMF performed better in the SNR and RSE than two kinds of FIR and four kinds of IIR filters.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.325-331
• /
• 2013

In this study, a complex eigenvalue analysis is implemented to verify the unstable mode of a brake system using ABAQUS software. The component participation factors and component modal participation factors are used to analyze the total contributions from each component and each component mode to a particular unstable system mode. This study shows that the 1.4-kHz unstable system mode comes from mode coupling between the 2nd nodal diametric mode and 3rd lateral axial mode (LAM) in the baseline model. A sensitivity analysis with a linking index is performed to prevent the mode coupling of the component modes. This linking index analysis shows the optimum mass loading position to move away the natural frequency of the 3rd LAM, which contributes to the unstable mode. Finally, a complex eigenvalue analysis is implemented with mass loading in the tie bar position, and no unstable system mode is generated in the low-frequency range (below 2 kHz).