• Journal of Korean Tunnelling and Underground Space Association
• /
• v.10 no.2
• /
• pp.105-118
• /
• 2008

Shotcrete is one of the main support materials in tunnelling. Its bonding state on excavated rock surfaces controls the safety of the tunnel: De-bonding of shotcrete from an excavated surface decreases the safety of the tunnel. Meanwhile, the bonding state of shotcrete is affected by blasting during excavation at tunnel face as well as bench cut. Generally, the bonding state of shotcrete can be classified as void, de-bonded, or fully bonded. In this study, the state of the back-surface of shotcrete is investigated using impact-echo (IE) techniques. Numerical simulation of IE technique is performed with ABAQUS. Signals obtained from the IE simulations were analyzed at time, frequency, and time-frequency domains, respectively. Using an integrated active signal processing technique coupled with a Short-Time Fourier Transform (STFT) analysis, the bonding state of the shotcrete can be evaluated accurately. As the bonding state worsens, the amplitude of the first peak past the maximum amplitude in the time domain waveform and the maximum energy of the autospectral density are increasing. The resonance frequency becomes detectable and calculable and the contour in time-frequency domain has a long tail parallel to the time axis. Signal characteristics with respect to ground condition were obtained in case of fully bonded condition. As the ground condition worsens, the length of a long tail parallel to the time axis is lengthened and the contour is located in low frequency range under 10 kHz.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.2
• /
• pp.125-131
• /
• 2003

In this paper Power Flow Finite Element Method(PFFEM) has been implemented to analyze the vibration of a plate in mid and high frequency ranges. In order to solve the vibration energy governing equation in Power Flow Analysis(PFA), The Finite Element Method(FEM) was used as a numerical tool. It allowed one to predict the distribution of displacement and Intensity in the plate vibrating at mid and high frequencies. The results were compared with the analytical solutions and the approximate FEM solutions. The comparison showed that PFFEM can be an effective tool to analyze the structural vibration in mid and high frequency ranges.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.10a
• /
• pp.19-24
• /
• 1995

단순한 형상의 소음기는 평면파이론에 의해 비교적 간단하게 음향성능을 해석적으로 구할 수 있다. 그러나 소음기의 형상이 복잡해지거나 해석하고자 하는 주파수의 범위가 평면파의 차단주파수 이상이 될 경우 소음기 내부의 음장이 평면파에서 벗어나게 되어 평면파 이론에 의한 해석은 실제와 상당한 오차가 발생하게 되므로 음장에 대한 3차원 해석이 필요하다. 이론적으로 3차원 문제를 해석할 수 있는 경우는 형상이 극히 단순한 경우에 국한되므로 유한요소법(FEM), 경계요소법(BEM)과 같은 수치해석적인 방법이 이용되고 있다. 경계요소법은 적분 커넬(kernel)의 특이성(singularity) 문제가 있지만 대상 영역의 경계면만을 이산화함으로써 모델링에 소요되는 시간과 노력을 절약할 수 있으므로 음향문제 해석에 있어서 효율적인 방법이라고 할 수 있다. 본 연구의 목적은 3차원 경계요소법 프로그램을 개발하고 평면파이론에 의한 해석이 어려운 여러가지 형태의 소음기에 대한 음향성능을 예측하고 실험으로 검증하는것이다. 특히, 단일영역으로 해석이 불가능한 다공형 소음기에 영역분할법을 적용하여 계산하고 결과를 검토하였다.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.820-821
• /
• 2011

본 논문은 단상 line-start permanent- magnet (LSPM) 전동기가 가지는 비동기 운전영역에서 나타나는 다양한 토크성분을 해석적 방법으로 분석한다. 비 동기속도에서의 정상상태 전류를 DQ 등가회로를 이용하여 유도하였으며, 이를 이용하여 유도전류와 제동전류의 주파수를 확인하였다. 마지막으로 시간차분 해석을 이용하여 비동기 운전영역의 특정 속도에 대한 토크와 전류를 분석하였으며, 주파수 변환을 이용하여 각 전류의 주파수 성분을 확인하였다.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.355-358
• /
• 1998

소신호 해석을 위해 사용되는 여러가지 방법을 비교하고 sinusoidal steady state analysis (S/sup 3/A) 방법을 이용해 반도체 소자를 소신호 해석한다. 소신호 행렬의 풀이방법으로 메모리 소비량이 적고 고주파수에서 행렬 연산으로 인한 잡음성분이 저은 전진해법을 사용한다. MEDICI에 의한 모의실험 결과와 비교하여 10GHz 이하의 주파수 영역에서는 비슷하였으나 10GHz~100GHz의 주파수영역에서 MEDICI에 비하여 정확한 결과를 보였다.

• Journal of Korea Society of Industrial Information Systems
• /
• v.4 no.1
• /
• pp.110-116
• /
• 1999

In this paper, signal processing is utilized to reduce the computational time which is one of weak point of FDTD(finite difference time domain) method. Compared with the direct FDTD. combination of FDTD and signal processing achieves the same type of accuracy in much shorter time The combination method spends 140 minutes to analyze the frequence characteristics of the microstrip lowpass filter while the direct FDTD consumes about 900 minutes. To verify the obtained results, microstrip lowpass filter is fabricated on dielectric substrate and the measured results are compared with the analyzed results. It is shown that measured results are in good agreement with the theoretical results.

• Journal of Ocean Engineering and Technology
• /
• v.8 no.1
• /
• pp.123-130
• /
• 1994

일반적으로 규칙파 또는 불규칙파중에서의 반잠수식 해양구조물의 응답을 추정할때, 선형계에 적합한 주파수 영역해석법을 사용하고 있다. 대다수의 해양구조물은 Lower Hull과 단면적이 일정한 Column으로 구성되어 있지만, 만약 Column의 단면적이 홀수에 따라 변화한다면 복원력항에 비선형계를 적용해야만 한다. 따라서 본 논문에서는 비선형 복원력을 고려한 반잠수식 해양구조물의 응답을 추정할 수 있는 시간 영역 해석법을 개발하였다. 그리고, Column형상이 다른 5개의 모델을 선정하여, 이들의 시간 영역 해석결과와 주파수 영역 해석 결과를 서로 비교하였다. 또한 파랑외력으로서 불규칙파를 적용할 때, 비선형 복원력이 해양구조물에 응답에 미치는 영향을 조사 하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.1
• /
• pp.38-44
• /
• 2010

In this paper, the higher order FDTD(Finite-Difference Time-Domain) method is used to obtain the frequency response characteristics of the cylindrical metamaterial slab. FDTD method is one of strongest electromagnetic numerical method which is widely used to analyze the metamaterial structure because of its simplicity and the dispersive FDTD equation which has the dispersive effective dielectric constant and permeability are derived to analyze the metamaterials. This derived dispersive FDTD equation has no errors in analyzing the dielectric materials but there are some time and frequency errors in case of analyzing the metamaterials. We used the higher order FDTD method to obtain the accurate frequency response of the metamaterials. Comparisons between the dispersive FDTD method and the higher order FDTD method are performed in this paper also. From the results, we concluded that more accurate frequency response for various metamaterials applications can be obtained using the proposed method in this paper.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.1
• /
• pp.14-19
• /
• 2010

In this paper, an efficient algorithm is developed to perform target rotational motion compensation to achieve the clear inverse synthetic aperture radar(ISAR) image. The algorithm is based on a time-frequency technique. This algorithm provides an efficient method to resolve the blurring image caused by the time-varying behavior of the target scattering centers and leads to a well-focused ISAR image. Results demonstrate that the time-frequency techniques can improve the blurring ISAR image when an aircraft is in complex motion, such as maneuvering, rotation and acceleration.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.2
• /
• pp.153-163
• /
• 2010

In this paper a frequency response analysis using Krylov subspace-based model reduction and its design sensitivity analysis with respect to design variables are presented. Since the frequency response and its design sensitivity information are necessary for a gradient-based optimization, problems of high computational cost and resource may occur in the case that frequency response of a large sized finite element model is involved in the optimization iterations. In the suggested method model order reduction of finite element models are used to calculate both frequency response and frequency response sensitivity, therefore one can maximize the speed of numerical computation for the frequency response and its design sensitivity. As numerical examples, a semi-monocoque shell and an array-type $4{\times}4$ MEMS resonator are adopted to show the accuracy and efficiency of the suggested approach in calculating the FRF and its design sensitivity. The frequency response sensitivity through the model reduction shows a great time reduction in numerical computation and a good agreement with that from the initial full finite element model.