• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.5
• /
• pp.393-400
• /
• 2011

The mass transport is very complicated at the area which has the macro tide and complex geometry such as Gyeonggi bay. Especially, the long period current has a strong influence on the estuarine ecosystem and the long-term distribution of substances. The long period current is caused by several external forcing, whose unique characteristic varies spatially and temporally. The variation characteristics of long period current is analysed and its generation mechanism is studied. The tidal nonlinear constituents such as overtide and compound tide are generated due to nonlinear interaction and it causes mean sea level setup. The tidal wave propagating up into estuary is transformed rapidly by decrease of cross-sectional area and depth. Therefore the mean sea level is getting rise toward upriver. The high and low tide level is similar between down-river(Incheon) and up-river(Ganghwa) during neap tide when the tidal deformation is decreased. The tidal phase difference between two tidal stations causes a periodic fluctuation of sea level difference. The low water level of Ganghwa station during spring tide does not descend under EL(-)2.5 m, but the low water level of Incheon fall down under EL(-)4.0 m. The variation of tidal range and its sea level are increased during spring tide. It is found that the long period current $M_{sf}$ is quite similar to that of sea level difference between the two tidal stations. It means that the sea surface inclination caused by the spatial difference of tidal deformation is important forcing for the generation of long period current.

• Composites Research
• /
• v.12 no.5
• /
• pp.1-11
• /
• 1999

Cyclic deformation and fatigue behavior of $Al/$Al_2O_3$ metal matrix composites and matrix alloy were studied. Hatigue strength Al/$Al_2O_3$ composites was about 210MPa, and that of Al matrix alloy was 170MPa. Most of the resultant displacement due to permanent plastic deformation occurred in less than the first 5% of fatigue life. In case of composites, decrease of cyclic displacement was smaller than that of matrix because the reinforcements acted as barriers to dislocation movement. Consequently, cyclic stress-displacement response curve can be considered to have these atages ; an initial few cycles of rapid hardening, followed by progressive hardening for most the fatigue life, and then just prior to failure, an instantaneous drop in stress carrying capability of the material due to multiple microcrack initiation, eventual coalescence of microcrack to form a macrocrack and then rapid macroscopic crack growth.

• Journal of the Korean Geophysical Society
• /
• v.4 no.3
• /
• pp.219-226
• /
• 2001

본 연구에서는 주기적인 하중하에서의 철근콘크리트 기둥의 이력응답거동을 예측할 수 있는 해석적인 모델의 개발을 다루고 있다. 철근콘크리트 기둥의 비탄성 휨, 전단 및 휨-전단 변형은 개발된 모델을 통하여 주기적인 변위하에서 검토되었다. 개발된 모델들을 포함한 해석치와 실험치와의 비교분석을 통하여 본 연구에서 개발된 모델들의 검증을 실시하였고, 이 비교분석을 통하여 휨-전단간의 상호작용의 중요성을 강조하였으며, 본 연구에서 개발된 모델들의 정확성, 효율성 및 타당성을 입증하였다.

• The Journal of Engineering Research
• /
• v.4 no.1
• /
• pp.151-158
• /
• 2002

본 연구에서는 주기적인 하중하에서의 철근콘크리트 기둥의 이력응답거동을 예측할 수 있는 해석적인 모델의 개발을 다루고 있다. 철근콘크리트 기둥의 비탄성 휨, 전단 및 휨-전단 변형은 개발된 모델을 통항 주기적인 변위하에서 검토되었다. 개발된 모델들을 포함한 해석치와 실험치와의 비교분석를 통하여 본 연구에서 개발된 모델들의 검증을 실시하였고, 이 비교분석을 통하여 휨-전단간의 상호작용의 중요성을 강조하였으며, 본 연구에서 개발된 모델들의 정확성, 효율성 및 타당성을 입증하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.1950-1957
• /
• 2004

Analysis for structures composed of materials containing regularly spaced in-homogeneities is usually executed by using averaged material properties. In order to evaluate the effective properties, a unit cell is defined and loaded somehow, and its response is investigated. The imposed loading, however, should accord to the status of unit cells immersed in the macroscopic structure to secure the accuracy of the properties. In this study, mathematical description for the periodicity of the displacement field is derived and its direct implementation into FE models of unit cell is attempted. Conventional finite element code needs no modification, and only the boundary of unit cell should be constrained in a way that the periodicity is preserved. The proposed method is applicable to skew arrayed in-homogeneity problems. Homogenized in-plane elastic properties are evaluated for a few representative cases and the accuracy is examined.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.2
• /
• pp.186-196
• /
• 2000

In this paper, modified square loop frequency selective surface for dualband communication antenna systems is proposed, and the scattering characteristics is discussed. The analysis for the problem of scattering by periodic structures with a dielectric slab is formulated using the spectral-domain immittance approach and Floquet's theorem. The method of moments which uses rooftop subdomain basis function is employed to solve the equations. Numerical results include the comparison between the transmission characteristic of general square loop and that of modified square loop. Also, the transmission characteristics of modified square loop for arbitrary incident angle and polarization is presented. To verify analysis results, modified square loop frequency selective surface was fabricated and the calculated results were compared with the measured results. The measured results showed good agreement with the calculated results.

• Journal of Welding and Joining
• /
• v.9 no.1
• /
• pp.9-15
• /
• 1991

국내에서는 1988년 하반기부터 50kg/mm$^{2}$급 TMCP강재가 생산되기 시작하여 국내 조선 업계도 TMCP강재의 사용이 가능하게 되었다. 이에 따라 국내수요가들은 국산 TMCP 강재의 원활한 사용을 위하여 생산자 주관으로 'TMCP강종개발위원회'를 주기적으로 개최하여 국산 TMCP강의 품질 평가와 함께 TMCP강의 단점 등을 여러 측면에서 검토, 보완하고 있다. 본 해설에서는 TMCP강재의 문제점들 중에서 선박용 강재로 사용하고자 할 때 가장 큰 문제점으로 제기되고 있는 절단변형에 대해 기술코자 한다.

• Journal of the Korean Geophysical Society
• /
• v.6 no.4
• /
• pp.213-219
• /
• 2003

This study in on the development of analytic model that can predict the hysterisis response of steel-concrete under the periodic loads. Analytic value and experimental value including developed model were compared and interpreted. From the comparing interaction between torque and shear was focused on the its importance.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.11
• /
• pp.1049-1055
• /
• 2008

Modern multidisciplinary computational fluid dynamics often incorporates moving boundaries, as would be required in the applications such as design optimization, aeroelasticity, or forced boundary motion. It is challenging to develop robust, efficient grid deformation algorithms when large displacement of the moving boundaries is required. In this paper, a volume grid deformation code is developed based on the finite macro-element and the transfinite Interpolation, and then interfaces to a structured multi-block Navier-Stokes in-house code. As demonstrated by an airfoil with pitching motion, the hysteresis loops of lift, drag and moment coefficients of the developed method are shown to be in good agreement with those of experimental data.

• Korean Journal of Materials Research
• /
• v.10 no.2
• /
• pp.155-159
• /
• 2000

Microstructural processes during high cycle fatigue are investigated according to plastic-strain hardening, crack formation, crack propagation and fracture. It is shown that the fatigue test resembles the uniaxial tensile test. The logarithm of the number of cycles to failure is proportional to the elongation in the tensile test. Under high cycle fatigue test, the strain is normally elastic. If the strain is absolutly elastic, fatigue could not result. But this is over simplication. Nearly all metals undergo a minor amount of plastic strain even at low stress. Damage accumulation leadling to crack formation can continue in the persistent slip bands at very low average plastic strain amplitude. In the ten­s sile test the overall specimen follows the failure procedure whilst in the high cycle fatigue test the local persistent slip band follows the failure procedure. However accumulations of strain per unit volume in the deforming region before failure in both cases are equal locally.