• 대한토목학회논문집
• /
• 제32권6A호
• /
• pp.347-354
• /
• 2012

본 연구에서는 Sine 파형 복부판을 갖는 I형 플레이트 거더의 비틂 상수와 �� 상수식을 제안한다. Sine 파형 복부판을 갖는 플레이트 거더는 일반적으로 기하학적 특성에 따라 높은 면외 방향 강성 및 전단강도, 비틂 강성을 갖는다. 특히, 플레이트 I형 거더의 횡-비틂 강도를 산정하는 데 있어서 부재 단면의 비틂 상수 및 �� 상수는 큰 영향을 미치는데, 종래의 수식으로는 Sine 파형 복부판의 이러한 단면상수를 합리적으로 산정하는 데 어려움이 있다. 따라서 본 연구에서는 Sine 파형 복부판의 기하학적 특성을 반영할 수 있는 새로운 제안식을 연구하였다. 쉘 요소를 사용한 I형 플레이트 거더의 순수 비틂 거동에 대한 유한요소해석결과를 통해 파형의 기하학적 특성에 따른 비틂 상수 변화를 분석하고 이를 회귀분석하여 수식을 제안하였다. 이후, 순수 비틂과 �� 비틂이 함께 존재하는 조건에서의 유한요소해석 결과를 통해 �� 상수 계산식을 제안하였다. 이 두 제안식은 단순 지지된 Sine 파형 복부판을 갖는 I형 플레이트 거더의 횡-비틂 좌굴해석 결과를 토대로 검증되었다. 본 연구에서 제안한 두 수식을 통해 Sine 파형 복부판을 갖는 I형 플레이트 거더의 중요한 두 단면 상수를 명확히 계산할 수 있고, 이를 통해 정확한 횡-비틂 좌굴 강도를 손쉽게 계산할 수 있다.

• 한국강구조학회 논문집
• /
• 제30권1호
• /
• pp.25-35
• /
• 2018

균일 외압을 받는 링 보강 원형단면 강재 쉘에 대하여 재료 및 기하학적 비선형 유한요소법(GMNIA)을 적용하여 외압강도를 평가하였다. 링 보강 쉘의 기하학적 초기결함의 진폭, 반경 대 두께 비, 링 보강재 간격 대 반경비 등이 외압강도에 미치는 영향을 분석하였으며, Eurocode 3과 DNV 설계기준에 의한 설계 외압 강도와 유한 요소해석으로 구한 외압강도를 비교 평가하였다. 기하학적 초기결함의 형상은 선형탄성 좌굴해석에 의한 좌굴모드를 적용하였으며 보강 쉘의 반경 대 두께 비는 250~500범위를 고려하였다.

• 대한기계학회논문집
• /
• 제15권1호
• /
• pp.28-40
• /
• 1991

본 연구에서는 4변이 단순 지지된 두꺼운 역대칭 앵글 플라이 적층판의 굽힘, 좌굴 및 진동 거동을 규명하였으며, 인장과 굽힘, 비틀림 사이의 결합 특성을 고려하 였고, 전단 변형을 고려하였다.또 유사 변환 개념을 도입하여 복합 재료 적층판의 거동을 일반화 하였다.

• 한국안전학회지
• /
• 제30권2호
• /
• pp.48-55
• /
• 2015

The number of collapse accidents relevant to form support since 2003 is 30 on the basis of statistical data from Ministry of Employment and Labor,. Total number of casualty was 138 (47 for deaths and 91 for injuries). The accident severity rate was high because the 4.6 casualties per one accident were occurred averagely although the incident rate was relatively low. Especially, one of form support members, the pipe supports have not been equipped adequately so that the accidents could have happened. In this regard, this study performed buckling test related to the effect of horizontal connection and slope in the single pipe which is one of typical pipe supports. The buckling load, which was estimated from the single pipe with the horizontal connectors theoretically and experimentally, was increased as more than 2 times compared to the buckling load obtained from the pipe supports without the connector. The buckling load was reduced as more than 26%, 34% slope of the single pipe comparing with 5% and 10% slope, respectively. Thus, the purpose of this study is to provide the guideline for installation and the maintenance of the pipe supports legally and institutionally to prevent the collapse accidents of the pipe supports.

• 한국안전학회지
• /
• 제30권2호
• /
• pp.41-47
• /
• 2015

Recently, a lot more disasters in the temporary structures happen because the stabilities of the temporary structures are disregarded by the reduction of the unit cost, using defective materials, the existing materials and so on. Pipe supports, which are one of the temporary structures, are basically used for the most constructing works such as buildings, bridges, plants and so on. In the most sites, adequate support installations of the pipe supports have not been performed although the presence of the guideline legally and institutionally. In this study, therefore, the collapse accidents of the pipe supports were investigated on the basis of theoretical analysis as well as the buckling tests by simulating the site support condition. Both the theocratical analysis and test results show that the buckling load in the fixed ends is at least 4 times larger than one in the pinned ends. This results will be utilized for safety assurance as well as accident prevention the in the field application.

• 한국안전학회지
• /
• 제25권1호
• /
• pp.57-61
• /
• 2010

Formwork is a temporary structure that supports its weight and that of fresh concrete as well as construction live loads. Scaffoling is a temporary frame used to support people and material in the construction or repair of buildings and other large structures. It is usually a modular system of metal pipes, although it can be made out of other materials. Bamboo is still used in some Asian countries like China. The purpose of a working scaffold is to provide a safe place of work with safe access suitable for the work being done. In construction site, steel pipes are usually used as scaffolds. In this study, scaffolding systems which is changed according to sleeper and joist space were measured by buckling test. Buckling load of respective scaffolding system was analyzed by structural analysis program(MIDAS). Buckling load of scaffold with/without wall connection and footboard was got by test and structural analysis. According to these results，we know that scaffolding system of case 3 is suitable. Buckling load of scaffold with wall connection is higher than without wall connection. So wall connection is important in scaffoling systems. Footboard in the scaffolding systems is not effective against promotion of buckling load. Finally, the present study results will be used to design scaffolding systems safely in the construction sites.

• 한국공간구조학회:학술대회논문집
• /
• 한국공간구조학회 2008년도 춘계 학술발표회 논문집
• /
• pp.80-85
• /
• 2008

본 논문에서는 쉘형 스페이스 프레임 구조물의 구조 불안정 특성을 조사한다. 대공간 구조물은 대경간을 가볍게 만들기 위해 두께비를 얇게 만들어야 하므로, 구조설계시 구조불안정 검토가 중요하다. 쉘형 구조물의 구조불안정은 다양한 조건에 따라 민감하게 반응하며, 이는 대변형을 수반하는 비선형 문제에 귀착하게 된다. 따라서 본 연구에서는 기하학적 비선형을 고려한 수치해석 기법을 통하여 쉘형 스페이스 프레임 구조물의 하중 및 경계조건에 따른 불안정 거동을 비교하고, 불안정 현상에 미치는 영향을 파악하여 기초적인 붕괴 메커니즘을 규명한다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.125-130
• /
• 2004

The vibration and buckling characteristics of the capsule for fuel irradiation test are studied. The natural frequencies of the capsule in air and under water are obtained by modal testing and finite element(FE) analysis using ANSYS program, and accelerations with flow are measured to estimate the compatibility with the operation requirement of the HANARO reactor. The experimental fundamental frequency of the capsule in the x and z direction is 8.5Hz and 8.75Hz in air, and 7.5Hz and 7.75Hz under water, respectively. The maximum amplitude of accelerations under the normal operating condition is measured as 11.0m/s$^2$ that is within the allowable vibrational limit(18.99m/s$^2$) of the reactor structure. Also, the maximum displacement at 100% flow is calculated as 0.13mm which is not interference with other nearby structures. FE analysis results show that the natural frequencies are found to be similar to those of the modal testing when three supporting parts are considered as simply supported conditions. From the buckling analysis, when the loading tool is applied, the critical buckling load of the capsule is 233N.

• 한국소음진동공학회논문집
• /
• 제14권8호
• /
• pp.741-748
• /
• 2004

The vibration and buckling characteristics of the capsule for fuel irradiation test are studied. The natural frequencies of the capsule in air and under water are obtained by modal testing and finite element (FE) analysis using ANSYS program, and accelerations with flow are measured to estimate the compatibility with the operation requirement of the HANARO reactor. The experimental fundamental frequencies of the capsule in the x and z direction are 8.5 Hz and 8.75 Hz in air, and 7.5 Hz and 7.75 Hz under water, respectively. The maximum amplitude of accelerations under the normal operating condition is measured as 11.0 m/s$^2$ that is within the allowable vibrational limit(18.99 m/s$^2$) of the reactor structure. Also, the maximum displacement at 100％ flow is calculated as 0.13 mm which is not interference with other nearby structures. FE analysis results show that the natural frequencies are found to be similar to those of the modal testing when three supporting parts are considered as simply supported conditions. From the buckling analysis, when the loading tool is applied, the critical buckling load of the capsule is 233 N.

• 한국공간구조학회논문집
• /
• 제1권1호
• /
• pp.117-124
• /
• 2001

In Single-layer latticed domes with rectangular network which is composed of ring of circumferential direction and rafter of longitudinal direction, that is, rib domes, if we use the cross-membered junction's method for the advantage in fabrication and construction, the eccentricity is occurred in the nodal point of crossing members. This paper is aimed at investigating the buckling characteristics for the effect of eccentricity according to rise-span ratios and distance of eccentricity. Analysis method is based on FEM dealing with the geometrically nonlinear deflection problems. The conclusion were given as follows: 1. The maximum decreasing ratio of buckling strength due to the junction's eccentricity is about 60% in models of this paper. 2. In the increasing ratio of buckling strength for rise-span ratio, that of Type 3 models is larger than that of type 2 models. On the other hand, that of Type 2 mode is larger than that of Type 3 for eccentricity-distance. 3. In the viewpoint of the value of buckling strength, that of Type 2 models is larger than that of type 3 models. The effect of the junction's rigidity on buckling strength is not great for overall models. Therefore if we use the cross-membered junction's method for the advantage in fabrication and construction, the method of Type 2 will have the great advantage of that of Type 3.