• Journal of the Korean Geotechnical Society
• /
• v.16 no.6
• /
• pp.69-77
• /
• 2000

본 연구에서는 전기삼투 배수와 제타포텐셜과 상관성을 규명하고자 하였다. 실험으로 직경 10cm, 길이 16cm의 원형 압밀시료에 일정 전압경사법으로 1V/cm의 직류접압을 가하여 0, 500, 3000 ppm의 납농도와 0, 230, 2300, 23000 ppm의 염분농도에서 각각 12일 과 14일 동안 전지삼투 배수량을 측정하였고, 같은 농도에서 kaolinite 현탁액의 제타포텐셜을 pH2부터 14범위에서 측정하였다. 실험결과 제타포텐셜은 전해질 농도와 pH 변화에 의존적이고, 전기삼투 투수계수와 비례관계가 있음을 확인할 수 있었다. 제타포텐셜에 따른 전기삼투 배수량과 비교한 결과, 전해질 농도가 낮을수록 제타포텐셜은 음의 값은 크고, 전기삼투 배수량도 더 증가하였다.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.8
• /
• pp.441-449
• /
• 2015

Studies on the flocculation of algae using various metal ions were carried out by measurements of optical density(OD) and zeta potential. Cyanobacteria were used as algaes. Flocculation efficiencies of cyanobacteria by an addition of metal ions were determined from OD values, and the effect of metal ions was greater in the order of $Al^{3+}$>$La^{3+}$>$Ho^{3+}$>$Fe^{2+}$>$Ca^{2+}$. Especially for trivalent metal ions, percentages of metal removed from cyanobacteria solutions on flocculation were measured, showing the same order as in flocculation efficiencies. Zeta potentials of cyanobacteria alone were measured with increasing the concentration, found to be all negative voltages, and were increased with increasing the concentration. The effect of pH on zeta potential of cyanobacteria solution was investigated. Below pH 5.5, the zeta potentials were steeply decreased with increasing pH, whereas in the range of $5.5{\leq}pH{\leq}10$ they were almost constant ($-46{\pm}1mV$) even with increasing pH. At a constant concentration of cyanobacteria ($A_{730}=0.25$), an increase in concentration of metal ions caused an increase in zeta potential of cyanobacteria solution, showing that the effect was greater in the order of $Al^{3+}$>$Ho^{3+}$>$La^{3+}{\gg}Mg^{2+}{\geq}Ca^{2+}{\gg}K^+$. At a constant metal concentration, zeta potentials were measured with increasing cyanobacteria concentration, showing that zeta potentials for $K^+$, $Mg^{2+}$ and $Ca^{2+}$ ions were negligibly changed, whereas those of $Ho^{3+}$ and $La^{3+}$ ions were decreased. Moreover, the effect of $Ho^{3+}$ ion on decreasing zeta potential was smaller than that of $La^{3+}$ ion. $Al^{3+}$ ions showed quite a different behavior that with increasing cyanobacteria concentration the zeta potentials increased and decreased thereafter. Hydrolysis of $Al^{3+}$ ions caused a difficulty to investigate coagulation or flocculation of cyanobacteria by measurement of zeta potential.

• Journal of Soil and Groundwater Environment
• /
• v.7 no.3
• /
• pp.85-94
• /
• 2002

Overall objective of this study was to evaluate the electrochemical characteristics of fine soils during the electrokinetic(EK) remediation. Zeta potential of kaolinite as a function of solution pH and surfactant concentration was investigated to make a relationship with electroosmotic flow direction and rate. During the EK experiments, pH of pore solution, electroosmotic permeability($k_e$), electric conductivity($\delta_e$) and voltage distribution was measured, respectively, The point of zero charge(PZC) of kaolinite was estimated to be about 4.2 and the zeta potential of kaolinite above PZC was more negative as solution pH increased. Sorption of surfactants on the kaolinite altered the zeta potential of kaolinite. resulting from the variation of electrochemical characteristics of kaolinite surface. hs the EK experiment progressed, low pH was predominant over most of the kaolinite specimen and thus resulted in very low mass and charge flow. The $k_e$ and $\delta_e$ was also affected by the variation of voltage drop across the EK column with time. Results from this study implied that zeta potential of kaolinite affected by the pH variation of pore solution and voltage distribution in soil column played important role in the determination of mass and charge flow during EK process. It was also suggested that pH adjustment or addition of suitable sorbates could alter the electrochemical characteristics of soil surface and thus maintain high mass and charge flow rate with time.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.1
• /
• pp.49-57
• /
• 2002

During the electrokinetic remediation, direct current applied to a soil-water-electrolyte system derives the variations of fluid transport phenomena in soil-water system and soil-water interface characteristics. Therefore, these variations affect the electrokinetic reaction. In this study, lab-scale electrokinetic remediation tests were performed to characterize the electrical and chemical parameters variation in soil. During the test, voltage gradient, electrical current, zeta potential and pH variations were measured. On the basis of experimental results, computer modeling techniques predicting the variations of these parameters are suggested.

• Journal of ILASS-Korea
• /
• v.8 no.1
• /
• pp.16-22
• /
• 2003

Zeta potential measurements of colloid particles suspended in a liquid are performed by a Zeta Meter developed. There are many applications of colloid stability in spray technology, paints, wastewater treatment, and pharmaceuticalse. Zeta potentials of charged particles are obtained by measuring the electrophoretic velocities of the particles using video enhanced microscopy and image analysis program. The values of zeta potential of polystyrene latex(PSL), $silica(SiO_2)$M, polyvinylidence difluoride(PVDF), silicon nitride, and alumina particles in deionized (DI) water were measured to be -40.5, -31.9, -25.2, -15.1 and -10.1mV, respectively. The particles having high zeta potential less than -20 mV are stable in DI water, because the double layers of them have strong repulsive forces mutually, and the particles having low zeta potential over -20mV are unstable due to Van Der Waals forces. Silica(>20nm), PSL, aluminum and PVDF particles were found to be stable that would remain separate and well disperse, while silicon nitride and alumina particles were found to be unstable that would gradually agglomerate in DI water.

• Applied Chemistry for Engineering
• /
• v.30 no.4
• /
• pp.453-459
• /
• 2019

In this study, the influence factors on the stability of the O/W (oil in water) emulsions prepared with coconut oil and the nonionic mixed surfactant (Tween 80-Span 80) were evaluated. The concentration and HLB value of the nonionic mixed surfactant, and the degree of agitation were used as manufacture factors. The stability of prepared O/W emulsions were measured with the mean droplet size, zeta-potential, emulsion stability index (ESI), and thermal instability index (TII). The mean droplet size of the prepared O/W emulsions was from 100 to 200 nm. As the concentration of mixed surfactant and the homogenization speed increased, the droplet sizes decreased, while the zeta-potential values increased. The effect of HLB values increased in the order of 6.0, 10.0 and 8.0, and at the HLB value of 8 the smallest mean droplet size as 120 nm was obtained whereas the largest value of the zeta-potential between 10 and 60 mV. From the results of ESI and TII, the stability of prepared O/W emulsions increased in order of 6.0, 10.0 and 8.0 of HLB values, and ESI and TII values were above 80% and below 20% respectively at HLB value of 8.0.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.1
• /
• pp.23-29
• /
• 2000

The agglomeration of titania particles with 30 nm in radii was simulated based on the colloidal stability. For surface potential increase from 4.5 to 16.8 mV the height of energy barrier increased. This tendency may explain the experimentally observed aggregation behavior where particles with smaller size and higher potential exhibited higher stability but form bigger and harder agglomerates with irregular shapes after drying.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2004.05b
• /
• pp.303-306
• /
• 2004

전기영동법을 이용한 초전도 후막의 제작공정은 그 특성상 외부의 물리적 방법으로 입자의 밀도를 향상시킬 수 없는 특징을 가지고 있으며 전착과정에서 수소가스가 발생됨으로 미세기공의 발생원인이되고다. 또한 건조 열처리과정에서 미세크랙의 발생이 되기도 한다. 따라서 공정과정에서 특성저하요인을 근본적으로 차단하고 밀도를 향상시킬 수 있는 공정에 대하여 연구하였으며 전착조건과 첨가제인 폴리머의 상관관계에 의한 최적화 방법에 대하여 연구하였다.

• Polymer(Korea)
• /
• v.28 no.6
• /
• pp.524-530
• /
• 2004

Polystyrene particles (PS) with poly(ethylene glycol) units on surface were formed by an emulsifier-free emulsion polymerization using styrene, poly(ethylene glycol) methacrylate (PEG-MMA) or poly(ethylene glycol) dimethacrylate (PEG-diMMA) at pH 7, and followed by freeze-drying to give the corresponding powders. The structures of PS particles were confirmed by FT-IR spectroscopy, and the particle size and distribution the PS particle were observed by scanning electron microscopy and particle analyzer. Monodisperse polymer particles were obtained at a concentration of PEG-MMA 2∼5 mol% or PEG-diMMA 1 mol% relative to styrene. The highest zeta potential of polymer surface was measured to be 183 mV at a polymer of PEG-MMA 5 mol%, which was measured in dielectric medium by means of ELS-8000 dynamic light scattering.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.39 no.3
• /
• pp.225-231
• /
• 2013

Oil in water nanoemulsion of astaxanthin was prepared by high pressure homogenization. The emulsifying conditions including emulsifier type, concentration and astaxanthin concentration were optimized. Stability of nanoemulsion was measured using zetasizer, freeze-fracture scanning electron microscope (FF-SEM), particle analyzer and colorimeter. The mean diameter of the dispersed particles containing astaxanthin ranged from 160 to 190 nm. Size distribution was unimodal and extended from 40 to 200 nm. The nanoemulsion prepared by glyceryl citrate/lactate/linoleate/oleate had smaller particle size and narrow size distribution. Stable incorporation of astaxanthin in nanoemulsion was performed and checked using high performance liquid chromatography (HPLC), freeze-fracture scanning electron microscope (FF-SEM). Physical stability of nanoemulsion was not significantly changed during storage at both light and thermal condition for a month with zeta potential value of -41 mV meaning stable colloid.