• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.2
• /
• pp.108-115
• /
• 1999

This paper proposes the robot inverse calibration method using a neural networks. A highorder networks called Pi-Sigma networks has been used. The Pi-Sigma networks uses linear summing units in the hidden layer and product unit in output layer. The inverse calibration model which compensates the difference of joint variables only between measuring value and analytic value about the desired pose(position orientation) of a robot is proposed. The compensated values are determined by using the weights obtained from the learning process of the neural networks previously. To prove the reasonableness the SCARA type direct drive robot(4-DOF) and anthropomorphic robot(6-DOF) are simulated. It shows that the proposed calibration method can reduce the errors of the joint variables from $\pm$3 to $\pm$0.1.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.2
• /
• pp.125-137
• /
• 2000

In this paper we propose a new approach to the development of the automatic vision system to examine and repair the steam generator tubes at remote distance. In nuclear power plants workers are reluctant of works in steam generator because of the high radiation environment and limited working space. It is strongly recommended that the examination and maintenance works be done by an automatic system for the protection of the operator from the radiation exposure. Digital signal processors are used in implementing real time recognition and examination of steam generator tubes in the proposed vision system. Performance of proposed digital vision system is illustrated by simulation and experiment for similar steam generator moldel.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.5
• /
• pp.76-82
• /
• 1999

During operating given working a robot manipulator makes some problems such as the accumulation of the error or the deviation from the command trajectory. These problems are mainly due to the disturbance noise or unmodeled system parameters. To solve these problems most of robot manipulators equip the controller. But if exact controller gains are not seleced we can't decrease the working efficiency(such as compensation about error or deviation) of the robot manipulator. So in this paper we present the controller gain tuning law by which we can find the controller gain which satisfies the per-formance specification of the robot manipulator during working of the robot. The proposed algorithm is derived from the Laypunov direct method. And by the simulation on the 4-axis SCARA type robot(SAMSUNG SM5 Robot) we guarantee the performance of this algorithm.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.6
• /
• pp.57-63
• /
• 1998

An adaptive control in the robotic GMA welding is employed to monitor information about weld characteristics and process parameters as well as to modify those parameters to hold weld quality within acceptable limits. Typical characteristics are the bead geometry, composition, microstructure, appearance, and process parameters which govern the quality of the final weld. The main objectives of this thesis are to realize the mapping characteristics of bead width through learning. After learning, the neural estimation can estimate the bead width desired form the learning mapping characteristic. The design parameters of the neural network estimator(the number of hidden layers and the number of nodes in a layer) are chosen from an estimation error analysis. A series of bead of bead-on-plate GMA welding experiments was carried out in order to verify the performance of the neural network estimator. The experimental results show that the proposed neural network estimator can predict the bead width with reasonable accuracy and guarantee the uniform weld quality.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.1
• /
• pp.121-129
• /
• 2017

In this study, we investigated a cooperative control system of assembly robots using wireless LAN. We developed two different types of robots to assemble three blocks on a workbench. Robot1 can assemble blocks on a workbench and Robot2 can carry blocks to Robot1. We constructed an ROS-based communication system and shared data. Three blocks and one workbench were recognized by camera-image processing By developing the UI using Windows programming language Visual C#, we evaluated the status of the robots and blocks and controlled the robots. The control system was developed by constructing all elements necessary for cooperative control, such as robot design and fabrication, motor control, ROS-based communication, and image processing. Thus, we completed fundamental tasks required for assembly.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.4
• /
• pp.386-394
• /
• 2011

This paper is concerned with the application of the vision control scheme for robot's point placement task in discontinuous trajectory caused by obstacle. The proposed vision control scheme consists of four models, which are the robot's kinematic model, vision system model, 6-parameters estimation model, and robot's joint angles estimation model. For this study, the discontinuous trajectory by obstacle is divided into two obstacle regions. Each obstacle region consists of 3 cases, according to the variation of number of cameras that can not acquire the vision data. Then, the effects of number of cameras on the proposed robot's vision control scheme are investigated in each obstacle region. Finally, the practicality of the proposed robot's vision control scheme is demonstrated experimentally by performing the robot's point placement task in discontinuous trajectory by obstacle.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.4
• /
• pp.28-34
• /
• 1998

This paper presents a new method for local obstacle avoidance of indoor mobile robots. The method combines a directional approach called the lane method and a velocity space approach. The lane method divides working area into lanes and then chooses the best lane to follow for efficient and collision-free movement. Then, the heading direction to enter and follow the best lane is decided, and translational and rotational velocity considering physical limitations of a mobile robot are determined. Since this method combines both the directional and velocity space method, it shows collision-free motion as well as smooth motion taking the dynamic of the robot into account.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.4
• /
• pp.441-447
• /
• 2015

This paper proposes a novel fuzzy-based multi-criteria decision making method and implements a footstep planner for humanoid robots with it. Humanoid robots require additional footstep planning process in addition to path planning for the autonomous navigation. Moreover, it is necessary to consider safety and energy consumption as well as path efficiency and multi-criteria decision making is indispensable. The proposed method can provide not only well- distributed and non-dominated, but also more preferable solutions for users. The planned footsteps by the proposed method were verified through simulation. The results indicate that the user's preference is properly reflected in optimized solutions maintaining solution quality.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.11 no.3
• /
• pp.21-27
• /
• 2002

We developed a Off-Line Graphic Simulator which can simulate a robot model in 3D graphics space in Windows 95 version. 4 ares SCARA robot was adopted as an objective model. Forward kinematics, inverse kinematics and robot dynamics modeling were included in the developed program. The interface between users and the off-line program system in the Windows 95's graphic user interface environment was also studied. The developing language is Microsoft Visual C++. Graphic libraries, OpenGL, by Silicon Graphics, Inc. were utilized for 3D graphics.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.1
• /
• pp.98-102
• /
• 2015

This paper proposes an autonomous navigation method for a nonholonomic mobile robot, based on the generalized Voronoi diagram (GVD). We define the look-ahead point for a given motion constraint to determine the direction of motion, which solves the problem of a minimum turning radius for the real nonholonomic mobile robot. This method can be used to direct the robot to explore an unknown environment and construct smooth feedback curves for the nonholonomic robot. As the trajectories can be smoothed, the position of the robot can be stabilized in the plane. The simulation results are presented to verify the performance of the proposed methods for the nonholonomic mobile robot. Furthermore, this approach is worth drawing on the experience of any other mobile robots.