• Progress in Medical Physics
• /
• v.13 no.2
• /
• pp.79-84
• /
• 2002

In this study, a cylindrical ultrasound applicator is developed for the treatment of vagina and rectum in combination with high dose rate brachytherapy. A cylindrical transducer (PZT-8, 1=1.5 cm, thickness=1.5mm OD=2.5 cm) was used as an energy source for induction of hyperthermia. Three single-element applicators were constructed to examine the performance of the PZT material. Vector impedance was measured to determine driving frequency. The efficiencies of the elements were determined using a radiation force technique to evaluate the feasibility of using the applicator as a hyperthermia source. A multi-element ultrasound applicator was designed using the PZT-8 material for the treatment of vagina. Results from the vector impedance measurements showed maximum magnitude at 1.78, 1.77, and 1.77 MHz for applicator 1,2, and 3, respectively. The radiation force measurements showed that the acoustic power of 40 watts was obtained in all three elements. The average efficiencies of the elements were 61.4, 65.2, and 54.0% for element 1, 2, and 3, respectively. The designed ultrasound hyperthermia applicator could be used in combination with high dose rate brachytherapy for the treatment of vagina and rectum. The use of this applicator with intracavitary brachytherapy could offer improved tumor control by increasing radiosensitiyity of the tumor.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.6
• /
• pp.535-543
• /
• 2013

The objective of this study was to analyse the residual stress in Larix kaempferi board during and after kiln-drying. The boards were primarily intended for using as laminar of cross laminated timber (CLT). In this study, the equivalence of moisture content by equalizing treatment was proved and reduction of residual stress by conditioning treatment was quantified. Prong test and slice test were carried out to analyse the residual stress in wood during drying. Transverse casehardening was measured immediately after making prong sample. Residual stress of four parts in wood from surface to center was analyzed quantitatively based on elastic deformation after just cutting slices from board. Tensile stress and compressive stress on the surface of board during drying did not exceed 2.2 MPa when boards were dried by kiln-drying schedule of T10-C4 and T12-D5. Because the tensile strength and compressive strength of transverse direction of Larix kaempferi lumber are 2.65 MPa and 4.60 MPa, application of more severe drying schedule can be recommended. Cup and twist were reduced by about 40% by equalizing and conditioning treatments after drying.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.8
• /
• pp.751-758
• /
• 2015

Mathematical models are actively used to reduce the experimental expenses required to understand physical phenomena. However, they are different from real phenomena because of assumptions or uncertain parameters. In this study, we present a calibration and validation method using a paper helicopter and statistical methods to quantify the uncertainty. The data from the experiment using three nominally identical paper helicopters consist of different groups, and are used to calibrate the drag coefficient, which is an unknown input parameter in both analytical models. We predict the predicted fall time data using probability distributions. We validate the analysis models by comparing the predicted distribution and the experimental data distribution. Moreover, we quantify the uncertainty using the Markov Chain Monte Carlo method. In addition, we compare the manufacturing error and experimental error obtained from the fall-time data using Analysis of Variance. As a result, all of the paper helicopters are treated as one identical model.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.193-193
• /
• 2000

박막 내의 잔류 응력은 막의 기계적 전기적 물성을 변화시키는 등 박막에 많은 영향을 끼치는 것으로 알려져 있다. 이러한 응력은 박막의 증착 공정중 여러 가지 증착 조건에 의해서 변화하게 되는데, 특히 스퍼터링 시스템의 경우에는 증착 압력과 사용하는 가스, 인가되는 전력 등 기본적인 증착조건들에 상당한 영향을 받는다. 이러한 영향은 금속 박막의 경우 상당히 잘 알려져 있다. 또한 반도체 공정에서 금속화 과정중 금속 전극의 단락등을 막기 위해 많은 연구가 진행되어 왔다. 본 논문에서는 고주파 마그네트론 스퍼터링 시스템을 사용하여 산화 아연(ZnO)을 증착하고 여러 공정 변수들에 따른 응력의 변화를 관찰하였다. 실험에서 ZnO 타겟을 사용하였으며, 작동 가스로는 아르곤과 산소를 사용하였다. 증착한 박막들은 모두 압축 응력을 보였으며, 박막의 응력에 가장 큰 영향을 미치는 요소들은 압력, 산소와 아르곤의 비, 기판과 타겟과의 거리 등이었는데, 인가 전력에는 거의 영향을 받지 않았다. 일반적으로 스퍼터링 시스템에서의 압축응력은 atomic peening에 의해서 형성되는데, 박막을 두드리는 높은 에너지의 아르곤이나 산소의 유량과 에너지의 1/2승에 비례하는 것으로 알려져 있다. 그러나 본 시스템에서는 인가 전력을 높여도 응력이 증가하지 않았고, 타겟과의 거리를 줄이면 오히려 응력이 감소함을 보였다. 이는 박막의 응력이 peening 하는 입자의 에너지뿐만이 아니라 증착되는 물질의 증착 속도와도 밀접한 관련이 있음을 보여준다. 즉, 증착속도가 증가하면 peening하는 입자가 끼치는 응력의 효과가 반감되기 때문으로 수식을 통해 증명할 수 있었다.진탄화 처리시간을 변화시켰을 때 화합물층의 생성은 ${\gamma}$'상으로부터 시작되고 $\varepsilon$상은 즉시 ${\gamma}$'상을 소모하면서 생성되어 일정시간이 지난 후 $\varepsilon$상은 안정화되며 질소가스농도가 증가할수록 화합물 층내의 $\varepsilon$상분율은 역시 증가하였다. 한편 CH4 가스농도는 처리되는 강종에 따라 차이를 보이며 적정 CH4 가스농도를 초과시에는 $\varepsilon$상 생성은 억제되고 시멘타이트상이 생성되었다.e에서 발생된 질소 플라즈마를 구성하는 이온들의 종류와 그 구성비율을 연구하였다.여러 가지 응용으로의 가능성을 가지고 있다. 그 예로 plasma processing, plasma wave에 의한 입자 가속, 그리고 가스 레이저 활성 매질 발생 등이 있다. 특히 plasma processing의 경우 helicon plasma는 높은 밀도, 비교적 낮은 자기장, remote operation 등이 가능하다는 점에서 현재 연구가 활발히 진행되고 있다. 상업용으로도 PMT와 Lucas Signatone Corp.에 서 helicon source가 제작되었다. 또한 높은 해리율을 이용하여 저유전 물질인 SiOF의 증착에서 적용되고 있다. 이 외에도 다수의 연구결과들이 발표되었다. 잘 일치하였다.ecursor 분자들이 큰 에너지를 가지고 기판에 유입되어 치밀한 박막이 형성되었기 때문으로 사료된다.을수 있었다.보았다.다.다양한 기능을 가진 신소재 제조에 있다. 또한 경제적인

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.1
• /
• pp.6-12
• /
• 2010

Fiber optic sensor using fiber Bragg grating(FBG) probes is used for monitoring strain and temperature distributed on the wide surfaces of large structures. In this paper, in order to use many FBG probes in one optical fiber line, we propose a complex multiplexing technology which is composed of two techniques, one is time division multiplexing and another is wavelength division multiplexing. However, we only investigate the characteristics of time division multiplexing because FBG sensors basically can be operated by wavelength division multiplexing. We calculate the optimal reflectivities and the lengthwise location of five FBG probes in serial connection in order to obtain the unique reflected intensities from the FBG probes. We fabricate five FBG probes with the reflectivities of 13%, 16%, 25%, 40% and 80%, which are determined by the theoretical calculation, and observe the signal reflected from each FBG in the time domain from the experiment. There are differences between experimental and theoretical results caused by the signal noise and the differences of reflectivities of FBG probes. But the experimental results shows the reflected signals of five FBG probes which prove the availability of complex multiplexing.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.325-331
• /
• 2016

Computational fluid numerical analysis using the commercial code CFX was performed to develop a Pelton turbine for a pico hydro power generator using the circulating water of a cooling tower in a large building. The performance of the Pelton turbine was examined for different design factors, such as the bucket shape, in which the Pelton wheel was connected in an appropriate manner to the pipe section, and the number of buckets in order to find the optimal design of Pelton turbine for a pico hydro power using surplus water. A benchmark test was carried out on the manufactured small scale Pelton turbine to validate the design method of the Pelton turbine by numerical analysis. The results obtained by comparing the flow characteristics and power output measured using the ultrasonic flowmeter, the pressure transducer and the oscilloscope with the numerical results confirmed the validity of the analytical design method. The possibility of developing Pelton turbines for kW class pico hydro power generators using surplus water with an average circulation velocity of 1.2 m/s for the chosen bucket shape and number of buckets in a 30 m high building was confirmed.

• Journal of Life Science
• /
• v.17 no.2 s.82
• /
• pp.235-240
• /
• 2007

AvrRpt2 protein triggers hypersensitive response (HR) and strong disease resistance when it is translocated from a bacterial pathogen Pseudomonas sp. to host plant cells containing a cognate RPS2 resistance protein through Type III Secretion System (TTSS). However, AvrRpt2 protein can function as the effector that suppresses a basal defense and enhances the disease symptom when functional RPS2 resistance protein is absent in the infected plant cells. Using Affymetrix Arabidopsis DNA chip, we found that many genes were specifically regulated by AvrRpt2 protein in the rps2 Arabidopsis mutant. Here, we showed that expression of AtERF11 that is known as a member of B1a subcluster of AP2/ERF transcription factor family was down regulated specifically by AvrRpt2. To determine its function in plant resistance, we also generated the Arabidopsis thaliana transgenic plants constitutively overexpressing AtERF11 under CaMV 355 promoter, which conferred an enhanced resistance against a bacterial pathogen, Pseudomonas syringae pv. tomato DC3000. Thus, these results collectively suggest that AtERF11 plays a role as a positive regulator for disease resistance against biotrophic bacterial pathogen in plant.

• Korean Journal of Optics and Photonics
• /
• v.28 no.1
• /
• pp.22-27
• /
• 2017

Time-encoded near-infrared spectroscopy (NIRS) system is proposed, based on a near-infrared (NIR) swept laser source, for comparison to the conventional NIRS method using a detector-type spectrometer. The cavity of the NIR swept laser source consists of a semiconductor optical amplifier (SOA) with a gain region around 800 nm, and several fiber-optic components. To change the output wavelength in time using an applied electric radio-frequency signal, an acousto-optic tunable filter (AOTF) is introduced in the fiber ring cavity configuration. To demonstrate the feasibility of an NIR swept laser source for NIRS imaging, the spectroscopic comparison of two kinds of absorbance-measuring systems a detector-type spectrometer using a white light source, and a source-type spectrometer using an NIR swept laser is successfully performed with an NIR-absorbing dye.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.2
• /
• pp.289-297
• /
• 2009

In the paper, we propose the methodology to extract training dataset automatically for supervised classification of road networks. For the preprocessing, we co-register the airborne photos, LIDAR data and large-scale digital maps and then, create orthophotos and intensity images. By overlaying the large-scale digital maps onto generated images, we can extract the initial training dataset for the supervised classification of road networks. However, the initial training information is distorted because there are errors propagated from registration process and, also, there are generally various objects in the road networks such as asphalt, road marks, vegetation, cars and so on. As such, to generate the training information only for the road surface, we apply the Expectation Maximization technique and finally, extract the training dataset of the road surface. For the accuracy test, we compare the training dataset with manually extracted ones. Through the statistical tests, we can identify that the developed method is valid.

• Journal of Broadcast Engineering
• /
• v.10 no.3
• /
• pp.422-435
• /
• 2005

Compared with analog broadcasting, digital broadcasting supports technical background to provide personalize the TV watching environment by offering broadcasting services that can adapt to viewers' preferences. However, current digital broadcasting shows limited services such as reservation recording, simple program guiding with an electronic program guide (EPG) on a personal video recorder system, and primitive data broadcasting by broadcasters. Therefore, the purpose of this paper is to suggest a new broadcasting environment which gives a person facility and a difference fur watching TV by serving enhanced personalized services. For that reason, we propose an intelligent broadcasting system which can minimize viewer's actions, and enhanced broadcasting services which are based on understanding of the semantics of broadcasting contents. To implement the system, agent technology as well as the MPEG-7 and TV-Anytime Forum (TVAF) are employed. For content-level services, real-time content filtering and personalized video skimming are designed and implemented. To verify the usefulness of the proposed system, we demonstrate it with a test-bed on which content-level personalized services are implemented.