• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.3
• /
• pp.12-20
• /
• 2023

This study presents basic data on how to secure stability by analyzing the change in tensile force of steel rod and the inclination characteristics of PSC BOX in the "Temporary fixation system using internal prestressing tendon", which is mainly applied to construction of superstructures by FCM. To date, it has been difficult to confirm the changes in tension force of the steel rod and the inclination of the PSC BOX because the steel rod was installed vertically inside the pier and the PSC BOX. Therefore, measurement of the change in length of the steel rod and the displacement of PSC BOX were performed using a micro-measured FBG sensor. Comparisons of the calculated tensile force and the residual tensile force of the steel rod revealed that the safety factor decreased in all bridges. The cause was mainly identified to be the loss of tensile force in fixation~1segment, and countermeasures are suggested. The analysis of the inclination characteristics showed that the inclination increased with the segment progresses even in bridges with sufficient safety factor, and the difference before and after the segment was confirmed. In addition, the increase in inclination was related to the loss of tension force in the steel rod, and the stress on the opposite sides of the inclination was further reduced. It is believed that upward tensile force is generated in the steel rod on the opposite side of the inclined side due to the unbalanced moment, causing the difference in stress of the steel rod between the two sides.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.5A
• /
• pp.511-518
• /
• 2009

This study was intended to compare and evaluate the adhesion of High flowing Self-compacting Concrete (HSCC), Conventional Concrete (CC) and deformed bar based on concrete strength 3 (30, 50 and 70 MPa), among the factors affecting the bond strength between concrete and rebar, after fabricating the specimen by modifying the rebar position at Horizontal reinforcement at bottom position (HB), horizontal reinforcement at top position (HT) and vertical reinforcement type (V). As a result of measuring bond strength of HB/HT rebar to evaluate the factor of the rebar at top position, the bond strength of HB/HT rebar at 50 and 70 MPa was 1.3 or less and at 30 MPa, HSCC and CC appeared to be 1.2 and 2,1, respectively. Thus, when designing the anchorage length according to the concrete structure design standard (2007) at HSCC 30, 50 and 70 MPa, it would be desirable to reduce the correction factor of anchorage length of the horizontal reinforcement at top position, which is suggested for the reinforcement at top position, to less than 1.3 of CC.

• Ecology and Resilient Infrastructure
• /
• v.4 no.1
• /
• pp.44-53
• /
• 2017

In order to investigate the response in fauna and biological communities of terrestrial insects to the vegetation encroachment on the sandbar, species composition, species diversity, functional species traits and community structure of land-dwelling insects sampled by a pit-fall trap were compared at the bare and vegetated sandbar of a typical sand-bed stream, the Naeseong Stream, Korea. Species diversity of the insects was increased but their density was decreased as the riparian vegetation encroached at the sandbar. In particular, indicator species of bare sandbar such as Cicindela laetescripta and Dianemobius csikii, were found at the bar sandbar. The insect communities were clearly classified at the bare and vegetated sandbar according to coverages of riparian plants. The food web of the bare sandbar was composed of detritus - detritivore and scavenger - predator consisted mainly of Coleoptera. On the other hand, the food web of the vegetated sandbar was composed of plants - sucking and chewing herbivore - parasitoid and predator. These results showed that biodiversity of terrestrial insects was increased, food web was changed from grazing to detritus food chain, and insect fauna specific bare sandbar disappeared as the riparian vegetation invaded on the sandbar of a sand-bed stream.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.6
• /
• pp.147-161
• /
• 2017

Generally, significant amount of reinforcements are used in nuclear power plant structures and it may cause several potential problems during the construction. In particular, it is more difficult to pour concrete into structural member joint area than other areas because of the significant congestion of the joint area due to a lot of hooked bars, embedded materials, and other reinforcements. The purpose of this study is to solve these problems due to the reinforcement congestion by using the high-strength(ASTM A615 Gr.80) headed deformed bars of large-sized diameter(43 mm & 57 mm) in nuclear power plant structures as a alternative of standard hooked bars. In order to use headed deformed bars effectively, It is necessary to find the method how to relax limits on their use while maintaining or improving the anchorage capacity. Therefore, this study will analyze the results of tests planned to evaluate the influence of the restricted variables, such as bar size, yield strength, clear cover thickness.

• Tunnel and Underground Space
• /
• v.28 no.6
• /
• pp.635-650
• /
• 2018

Many people have been recognized that the Korean Peninsula is no longer safe area from the earthquake by the recent earthquakes occurred in the country. The earthquakes that occurred at Pohang and Gyeongju appeared differently from them considered in the seismic design and researches on the seismic design method have been also conducted by many researchers. Studies on seismic loads are mainly focused on existing superstructures, and research involving them has been actively carried out in reality. However, paper regarding structural stability of reinforcement from seismic load such as soil-nails, rock-bolts, ground anchors which were constructed to ensure stability of serviced structure have been published rarely. In this study, ground anchor been effected by static load and seismic load which is settled in the weathered rock is analyzed. Results for static load are obtained from field test and seismic load is from numerical analysis. In this study, the behavioral characteristics of the ground anchor were analyzed by numerical analysis in case of seismic loading based on the result of the in-situ tensile test of the ground anchor settled weathered rock. As a result, settlement of concrete block due to application of tension force for ground anchor occurred as well as following loss of axial force for ground anchor. Also, as bond length and period of seismic load are longer, increasement of displacement is greater.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.1017-1021
• /
• 2006

인공순환수로에 정육면체 수리구조물을 구간별로 설치하여 흐름특성에 따른 깔따구의 서식경향을 조사하였다. 정밀한 흐름특성을 분석하기 위하여 난류계산을 수행하였으며, 인공순환수로에 깔따구를 투입하고 3일경과 후 깔따구의 개체수를 조사하였다. 인공순환수로는 단면 폭 29cm, 높이 30cm인 구조로 제작되었으며 직선구간의 길이는 120cm이다. 인공순환수로의 직선구간에 길이 10cm의 정육면체 수리구조물을 20cm 간격으로 양쪽 벽면부에 4개씩 균일하게 설치하였다. 자연하천에서 채집된 원수를 수심 20cm가 되도록 투입한 후 유기물을 하상에 고르게 깔고, 회전날개를 이용하여 평균유속 10cm/s로 안정화 시킨 후 깔따구 투입하였다. 실험시작 3일 경과 후, 깔따구의 서식경향을 조사한 결과 깔따구는 수리구조물 직하류부에 주로 서식하였다. 이는 주 흐름방향 유속분포가 수리구조물 후방에서 급격히 작아져 깔따구들이 정착하기 좋은 환경을 제공하기 때문인 것으로 판단된다. 또한 인공순환수로 직선구간의 안쪽 벽면과 바깥쪽 벽면의 깔따구 개체수는 안쪽 벽면이 바깥쪽 벽면에 비하여 2배 정도 많다. 이는 수리구조물 사이 안쪽 벽면 하상의 시계방향 회전흐름 때문으로 분석되며 상대적으로 이러한 흐름은 바깥쪽 벽면에서 작다. 실험 및 수치해석 결과, 깔따구는 상대적으로 유속이 작은 곳에 서식하며, 이차류의 경향에 따라 서식처를 이동하는 것으로 분석되었다. 향후 생태적 기능을 고려하여 다양한 수리학적 조건 하에서 난류계산 및 유속측정을 통한 연구가 필요하다. 이와 같은 연구는 친환경적으로 하천을 복원시키는데 유용한 자료를 제공할 수 있을 것으로 생각된다.은 silt나 clay보다 입경이 큰 모래나 자갈을 경유 하면서 오염물의 저감효과가 감소한 것으로 판단된다. 그러나 유입유량의 대부분이 표면으로 유출된다는 점을 고려할 때 표면유출수의 오염도를 낮추는 것이 유입오염물 저감효과에 보다 큰 효과가 있을 것으로 판단된다.문에 자료의 이상적 유지 관리가 이루어지며 복잡한 2차원 수질해석 모형을 수월하게 운영할 수 있는 시스템으로 개발하였다.제외하면, 부자측정 방법에 의한 유량산정시 가장 큰 오차원인은 홍수시 측정된 유속측선의 위치와 홍수 전후로 측정된 횡단면상의 위치가 일치하지 않는 점과, 대부분 두 측정 구간의 평균값을 대푯값으로 사용한다는 점이다. 본 연구는 다년간의 유량 측정 및 검증 경험과 자료를 토대로 현장에서 부자를 이용하여 측정된 측정성과를 정확도 높은 유량자료로 산정하는데 있어서의 문제점을 도출하고, 이로 인해 발생하는 오차를 추정하여 그 개선방안을 제시해 보고자한다. 더불어 보다 정확한 유량 산정을 위한 기준과 범주를 제시하고자 한다.리적 특성을 잘 반영하며, 도시지역의 복잡한 배수시스템 해석모형과 지표범람 모형을 통합한 모형 개발로 인해 더욱 정교한 도시지역에서의 홍수 범람 해석을 실시할 수 있을 것으로 판단된다. 본 모형의 개발로 침수상황의 시간별 진행과정을 분석함으로써 도시홍수에 대한 침수위험 지점 파악 및 주민대피지도 구축 등에 활용될 수 있을 것으로 판단된다. 있을 것으로 판단되었다.4일간의 기상변화가 자발성 기흉 발생에 영향을 미친다고 추론할 수 있었다. 향후 본 연구에서 추론된 기상변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기 위한 연구가 필요할 것이다.게

• Journal of the Korea Concrete Institute
• /
• v.29 no.2
• /
• pp.159-167
• /
• 2017

A precast concrete deck system is considered an effective alternative in terms of its rapid construction and quality assurance than cast-in-place concrete deck. In precast concrete deck system, structural performance and serviceability are mostly determined by the connection methods between the precast decks. This research proposes more improved precast deck system with asymmetric ribbed connection details improving the disadvantage of previous precast deck system such as difficulties in assembling precast decks. And in this precast deck system, a separate form is not required at the site because partition wall of the precast decks serves as a form when placing non-shrinkage mortar in the connection part of the precast decks. Therefore, rapid construction is possible. Flexural performance is verified through load tests considering main parameter such as rib length in the precast deck connection. From the test results, it can be inferred that the development of the rebar and prevention of adhesion failure in the partition wall of the precast deck system are important factors in securing the flexural performance. Although the structural performance of the precast deck system with asymmetric connection details is gradually reduced as the rib length in the precast deck connection increases, the proposed precast deck system shows sufficient flexural performance and can be applied to the connection part of precast decks effectively.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.1
• /
• pp.175-181
• /
• 2004

This study is about a section where underground water level occurs at the underground 5m depth by the excavation of the ground, as a stream is adjacent to a excavation section of High Speed Railway ${\bigcirc}{\bigcirc}$ Station construction sections and a reservoir being always full of water is located at the left side of the construction section. Therefore this test is executed for the design and construction of buoyance anchors able to permanently prevent buoyance by the underground water level at working and for the stable construction and permanent smooth maintenance of structures. In this test, bar type anchors are divided according to their length and standard to execute test-anchor test, and In spot test, 9 test-anchors test, proof test to construction process, suitability test and acceptance test are executed 4 times to 9 test-anchors by dividing anchors according to the length of permanent anchor, the outer diameter of bar and boring diameter. Standard motion characteristic centering on load transmission and break mechanism of bar-type anchors for the prevention of buoyance will be showed in the thesis.

• Korean Journal of Construction Engineering and Management
• /
• v.24 no.5
• /
• pp.52-62
• /
• 2023

The objective of this study is to propose an automated algorithm for precise cutting length of slab rebar complying with regulations such as anchorage length, standard hooks, and lapping length. This algorithm aims to improve the traditional manual quantity take-off process typically outsourced by external contractors. By providing accurate rebar quantity data at BBS(Bar Bending Schedule) level from the bidding phase, uncertainty in quantity take-off can be eliminated and reliance on out-sourcing reduced. In addition, the algorithm allows for early determination of precise quantities, enabling construction firms to preapre competitive and optimized bids, leading to increased profit margins during contract negotiations. The proposed algorithm not only streamlines redundant tasks across various processes, including estimating, budgeting, and BBS generation but also offers flexibility in handling post-contract structural drawing changes. In particular, the proposed algorithm, when combined with BIM, can solve the technical problems of using BIM in the early phases of construction, and the algorithm's formulas and shape codes that built as REVIT-based family files, can help saving time and manpower.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.2
• /
• pp.219-229
• /
• 2003

The extended tangent stiffness matrices and force-deformation relations of the elastic catenary element were initially derived through the addition of the unstrained length of cables to unknown nodal 'displacements. A beam-column element was then introduced to model the deck and pylon of cable-stayed bridges. The conventional geometric nonlinear analysis, initial force method, and TCUD method were summarized, with an effective method combining two methods presented to determine the initial shapes of cable-stayed bridges with dead loads. In this combined method, TCUD method was applied to eliminate vertical and horizontal displacements at cable-supported points of decks and on top of pylons, respectively. The initial force method was also adopted to eliminate horizontal and vertical displacements of decks and pylons. Finally, the accuracy and validity of the proposed combined method were demonstrated through numerical examples.