• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.7
• /
• pp.120-128
• /
• 2019

It is very important to verify the seismic performance and stability of the power plant fixture in the domestic power plant, because earthquakes have increased in frequency around the world which resulted in the frequent occurrence of power plant damage caused by the failure of electric power facilities. In this study, through the on-site inspection of power plant fixation unit installed in domestic power plants, we carried out structural performance evaluation of the fixation unit anchor bolts installed on the concrete slabs. The field survey showed M12 J hook anchor bolts were used. Anchor bolt pullout and shear performance evaluation were performed based on ASTM E 488-96 standard. Moreover, artificial crack with the width of 0.5 mm was applied during the experiment based on ATM355.4 and ETAG 001. The comparison of M12 J hook anchor bolt pullout and shear test result to design value required in domestic and international design standard, show a satisfactory result. M12 J hook anchor pullout and shear performance was found to be about 35% and 7%, respectively, higher than the required design value.

• Journal of Korean Society for Atmospheric Environment
• /
• v.7 no.3
• /
• pp.180-188
• /
• 1991

기후변화를 나타내는 연구 결과들은 기온이나 강수량을 대상으로 하여 두 기간 평균치의 비교, 5년 이동평균치의 圖示, 회귀분석 등의 방법들을 사용하여 발표되지만 대부분의 경우 밑바탕이 되는 모집단의 통계적 특성을 엄격히 검토하지 않는 정성적인 분석인 경우가 많다. 서울, 부산, 인천, 목포 등 4개 지점의 80년 동안의 연강수량과 연평균기온자료를 분석한 결과 기온은 정규분포를 나타내므로 전통적인 t-검정과 회귀분석을 적용할 수 있다. t-검정 결과 두 기간(1920 $sim$ 1949, 1961 ~ 1990)은 연평균기온에서 0.3$^{\circ}$C에서 $0.8^{\circ}$C의 의의있는 차이를 보였다. 최근 30년의 연평균기온자료를 회귀분석한 결과 1년에 $0.02^{\circ}$C의 증가경향을 나타내었다. 연강수량은 정적인 왜곡도를 보이므로 정규분포를 가정하는 母數的 통계분석을 적용해서는 안되며 비모수적 통계분석법을 적용해야 한다. 연강수량의 분석에는 t-검정에 상응하는 Mann-Whitney 검정을 적용해 본 결과 두 기간(1920 ~ 1949, 1961 ~ 1990)의 평균은 통계적으로 의의있는 차이가 없었다. 회귀분석에 상응하는 Mann's 검정과 이 연구에서 새로이 제안된 Median Slope Change Estimator를 적용해 본 결과 역시 통계적으로 의의있는 변화가 없었다. Median Slope Change Estimator는 비모수적 통계치로서 회귀분석의 기울기에 해당하는 연변화를 나타낼 수 있는데 분석하려는 자료의 정규분포성을 요구하지 않으며 異常點(outlier) 영향에 덜 민감하다는 장점이 있으므로 주목하여 연구할 만한 가치가 있다.^{\circ}$~40$^{\circ}$ 구간에서는 ${\sigma}_c$와 I$_{sa}$, 40$^{\circ}$~90$^{\circ}$ 구간에서는 ${\sigma}_c$와 I$_{sd}$가 각각 양호한 상관관계를 보여준다. 또한 상관비(K=${\sigma}_c$/I$_s$)는 약 13정도로서 일반적으로 적용되는 비, 24와 상당한 차이가 있다. 이러한 현상은 호상편마암의 구조적 및 역학적 이방성 특성으로 인한 결과라고 판단된다. 한편 맥암류에서 K가 약 23정도로서 일반적인 비 24에 상당히 접근한다. 따라서, 이방성 구조가 뚜렷한 암석에서 상관비 24는 항상 적용할 수는 없으며 일축압축강도시험과 병행 실시하여 적용하는 것이 바람직하다.다. 한편, 감작감염후 77일과 도전감염후 7일의 시점에 있어서 sRBC에 대한 면역능에 미치는 영향은 전자의 양상과 비슷하였는데 대조에 비하여 지연형 과민반응과 로제트 형성능이 현저하게 저하되었다. 이 시점에 있어서의 유충회수율은 대조가 10.5% 이었는데 비하여 8.3%이었다.e also compared for the cases of Kim et al, which again gives promising agreement.면적 306~453$\textrm{cm}^2$, 유색계의 경우 수당면적 340~453$\textrm{cm}^2$ 일 때 경제능력을 제대로 발휘할 수 있고 경제성이 있는 것으로 나타났다. 첨가구가 높은 경향이 있었다8.4%. 79.7% 그리고 80.2%였다.

• Journal of the Korea Concrete Institute
• /
• v.23 no.2
• /
• pp.135-144
• /
• 2011

Recently, researches about fiber reinforced polymer (FRP) which has excellent durability, corrosion resistance, and tensile strength as a substitution material to steel tendon have been actively pursued. This study is performed to examine FRP tendon used prestressed beam's safety under service load. The specimen was a prestressed concrete beam with internal bonded FRP tendon. In order to compare the member fatigue capacity, a control specimen of a prestressed concrete beam with ordinary steel tendon was tested. A fatigue load was applied at a load range of 60%, 70%, and 80% of the 40% ultimate load, which was obtained though a static test. The fatigue load was applied as a 1~3 Hz sine wave with 4 point loading setup. Fatigue load with maximum 1 million cycles was applied. The specimen applied with a load ranging between 40~60% did not show a fatigue failure until 1 million cycles. However, it was found that horizontal cracks in the direction of tendons were found and bond force between the tendon and concrete was degraded as the load cycles increased. This fatigue study showed that the prestressed concrete beam using FRP tendon was safe under a fatigue load within a service load range. Fatigue strength of the specimen with FRP and steel tendon after 1 million cycles was 69.2% and 59.8% of the prestressed concrete beam's static strength, respectively.

• Composites Research
• /
• v.27 no.4
• /
• pp.168-173
• /
• 2014

The optimum condition of glass fiber/epoxy composites was investigated according to mixing ratio of two epoxy matrices. Novolac type epoxy and isocyanate modified epoxy were used as composites matrix. Based on chemical composition of mixing matrix, optimum mixing ratio of epoxy resins was obtained through various experiments. In order to investigate thermal stability and interface of epoxy resin, glass transition temperature was observed by DSC instrument, and static contact angle was measured by reflecting microscope. Change of IR peak and $T_g$ was conformed according to different epoxy mixing ratio. After fabrication of glass fiber/epoxy composites, tensile, compression, and flexural properties were tested by UTM by room and high temperature. The composites exhibited best mechanical properties when epoxy mixing ratio was 1:1.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.15 no.4
• /
• pp.45-54
• /
• 2011

A simple model for reinforced concrete shear walls with boundary elements is proposed, which is a macro-model composed of spring elements representing flexure and shear behaviors. The flexural behaviour is represented by vertical springs at the wall ends, where the moment strength and rotational capacity of the wall are based on section analysis. The shear behaviour is represented by a horizontal spring at the wall center, where the key parameters for the shear behavior are based on the flexural behaviour since the shear walls with boundary elements are governed by the flexure. The proposed model was prepared with the results of hysteretic tests of the shear walls, and then the reliability of the hysteretic rule and variables was investigated by nonlinear dynamic analyses. Using parametric study with nonlinear dynamic analyses, the effect of the variables on demand and capacity, which are major parameters in seismic performance evaluation, are investigated. Results show that the measured and calculated shear forces versus the shear distortion relationships are slightly different, but the global response is well simulated. Furthermore, the demand and capacity are also changed in a similar way to the change in the major parameters so that the proposed model may be appropriate for reinforced concrete shear walls with boundary elements.

• Composites Research
• /
• v.24 no.1
• /
• pp.45-50
• /
• 2011

Transparent and conductive carbon nanotube on polyethylene terephthalate (PET) were prepared by dip-coating method for self-sensing multi-functional nanocomposites. The changes in the electrical and optical properties of CNT coating mainly depended on the number of dip-coating, concentration of CNT solution. Consequently, the surface resistance and transmittance of CNT coating were sensitively controlled by the processing parameters. Surface resistance of CNT coating was measured using four-point method, and surface resistance of coated CNT could be better calculated by using the dual configuration method. Optical transmittance of PET film with CNT coating was evaluated using UV spectrum. Surface properties of coated CNT investigated by wettability test via static and dynamic contact angle measurement were consistent with each other. As dip-coating number increased, surface resistance of coated CNT decreased seriously, whereas the transmittance exhibited little lower due to the thicker CNT networks layer. Interfacial microfailure properties were investigated for CNT and indium tin oxide (ITO) coatings on PET substrates by electrical resistance measurement under cyclic loading fatigue test. CNT with high aspect ratio exhibited no change in surface resistance up to 2000 cyclic loading, whereas ITO with brittle nature showed a linear increase of surface resistance up to 1000 cyclic loading and then exhibited the level-off due to reduced electrical contact points based on occurrence of many micro-cracks.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.5
• /
• pp.443-451
• /
• 2013

Acoustic emission(AE) has emerged as a powerful nondestructive tool to detect any further growth or expansion of preexisting defects or to characterize failure mechanisms. Recently, this kind of technique, that is an in-situ monitoring of inside damages of materials or structures, becomes increasingly popular for monitoring the integrity of large structures like a huge wind turbine blade. In this study, the activities of AE signals generated from external artificial sources was evaluated and located by new developed signal mapping source location method and this test is conducted by 750 kW full-scale blade. And a new source location method was applied to assess the damage in the wind turbine blade during step-by-step static load test. In this static loading test, we have used a full scale blade of 100 kW in capacity. The results show that the acoustic emission activities give a good agreement with the stress distribution and damage location in the blade. Finally, the applicability of the new source location method was confirmed by comparison of the result of source location and experimental damage location.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.8
• /
• pp.5-14
• /
• 2010

Recent researches on the behavior of gravelly soils have been focused mainly on the relative density or on the gravel content. And some researchers presented the liquefaction behavior based on the relative density whereas others based on the gravel content of gravelly soil. However the relative densities vary with gravel content and relative density is not enough to fully express the behavior of gravelly soils. Therefore in this research state parameter which considers void ratio and effective confining pressure is introduced and Steady State Line(SSL) of gravelly soils for various gravel content are determined by undrained triaxial tests in order to express the behavior of gravelly soils. From the research the position of SSL moved downward with gravel content. And the same density of soil showed dense sand behavior or loose sand behavior depending upon the confining pressure. Especially relative density 80% of gravelly soil showed loose sand behavior under high confining pressure. However the gravelly soils with similar state parameters showed similar stress behaviors. It can bee seen that state parameter is useful tool to evaluate undrained behavior of gravelly soils. Also state parameter and undrained strength showed good correlations.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.911-917
• /
• 2015

The objective of this work focuses on the analysis of injection rate and macroscopic spray behavior characteristics with injection pressures as well as combustion and exhaust emission characteristics with injection timing and injection pressure by using a common rail single-cylinder diesel engine. The injection rate was measured by applying the Bosch method, and macroscopic spray behavior characteristics were analyzed with a constant-volume vessel and a high-speed camera. In addition, combustion and emission characteristics were analyzed in a common-rail single-cylinder diesel engine with precise control of fuel injection timing and pressure. For injection pressures of 30MPa and 50MPa, the injection rate was higher at 50 MPa, and the spray development (penetration) was also higher in the same elapsed time. The peak in-cylinder pressure and rate of heat release showed a tendency to decline as injection timing was delayed, and the peak in-cylinder pressure and rate of heat release were slightly higher for higher injection pressures. Higher injection pressures also reduced the mean effective pressure, while the indicated mean effective pressure and torque increased as injection timing was delayed to TDC. Nitrogen oxides had a peak level at injection timings of $BTDC20^{\circ}$(30MPa) and $BTDC15^{\circ}$(50MPa); carbon monoxide emissions were reduced by delaying injection timing from $BTDC30^{\circ}$.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.3
• /
• pp.31-37
• /
• 2018

This study evaluates the dynamic tensile behavior of HPFRCC according to compressive strength levels of 100, 140 and 180 MPa. Firstly, the compressive stress-strain relationship of 100, 140 and 180 MPa class HPFRCC was analyzed. As a result, the compressive strengths were 112, 150 and 202 MPa, respectively, and the elastic modulus increased with increasing compressive strength. The static tensile strengths of HPFRCC of 100, 140 and 180 MPa were 10.7, 11.5 and 16.5 MPa, and tensile strength also increased with increasing compressive strength. On the other hand, static tensile strength and energy absorption capacity at 100 and 140 MPa class HPFRCC showed no significant difference according to the compressive strength level. It was influenced by the specification of specimen and the arrangement of steel fiber. As a result of evaluating the dynamic impact tensile strength of HPFRCC, tensile strength and dynamic impact factor of all HPFRCCs tended to increase with increasing strain rate from 10-1/s to 150/s. In the same strain rate range, the DIF of the tensile strength was measured higher as the compressive strength of HPFRCC was lower. It is considered that HPFRCC of 100 MPa is the best in terms of efficiency. Therefore, it is advantageous to use HPFRCC with high compressive strength when a high level of tensile performance is required, and it is preferable to use HPFRCC close to the target compressive strength for more efficient approach at a high strain rate such as explosion.