• Korean Journal of Environmental Agriculture
• /
• v.41 no.2
• /
• pp.82-94
• /
• 2022

BACKGROUND: Spiropidion and its metabolite are tetramic acid insecticide and require the establishment of an official analysis method for the safety management because they are newly registered in Korea. Therefore, this study was to determine the analysis method of residual spiropidion and its metabolite for the five representative agricultural products. METHODS AND RESULTS: Three QuEChERS methods (original, AOAC, and EN method) were applied to optimize the extraction method, and the EN method was finally selected by comparing the recovery test and matrix effect results. Various adsorbent agents were applied to establish the clean up method. As a result, the recovery of spiropidion was reduced when using the dispersive-SPE method with MgSO₄, primary secondary amine (PSA), graphitized carbon black (GCB) and octadecyl (C₁₈) in soybean. Color interference was minimized by selecting the case including GCB and C18 in addition to MgSO₄. This method was established as the final analysis method. LC-MS/MS was used for the analysis by considering the selectivity and sensitivity of the target pesticide and the analysis was performed in MRM mode. The results of the recovery test using the established analysis method and inter laboratory validation showed a valid range of 79.4-108.4%, with relative standard deviation and coefficient of variation were less than 7.2% and 14.4%, respectively. CONCLUSION(S): Spiropidion and its metabolite could be analyzed with a modified QuEChERS method, and the established method would be widely available to ensure the safety of residual insecticides in Korea.

• Korean Journal of Mineralogy and Petrology
• /
• v.35 no.2
• /
• pp.111-123
• /
• 2022

Carbonate green rust (CGR) and sulfate green rust (SGR) commonly occur in nature. In this study, CGR and SGR were synthesized through co-precipitation, and their formation mechanisms and physicochemical properties were investigated. X-ray diffraction (XRD) and Rietveld refinement showed both CGR and SGR with layered double hydroxide structure were successfully synthesized without any secondary phases under each synthetic condition. Refined structural parameters (unit cell) for two green rusts were a (=b) = 3.17 Å and c = 22.52 Å for CGR and a (=b) = 5.50 Å and c = 10.97 Å for SGR with the crystallite size 57.8 nm in diameter from (003) reflection and 40.1 nm from (001) reflections, respectively. Scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS) results showed that both CGR and SGR had typical hexagonal plate-like crystal morphologies but their chemical composition is different in the content of C and S. In addition, Fourier transform infrared (FT-IR) spectroscopy analysis revealed that carbonate (CO₃^2-) and sulfate (SO₄^2-) molecules were occupied as interlayer anions of CGR and SGR, respectively. These SEM/EDS and FT-IR results were in good agreement with XRD results. Changes in the solution chemistry (i.e., pH, Eh and residual iron concentrations (Fe(II):Fe(III)) of the mixed solution) were observed as a function of the injection time of hydroxyl ion (OH^-) into the iron solution. Three different stages were observed in the formation of both CGR and SGR; precursor, intermediator, and green rust in the formation of both CGR and SGR. This study provides co-precipitation methods for CGR and SGR in a way of the stable synthesis. In addition, our findings for the formation mechanisms of the two green rusts and their physicochemical properties will provide crucial information with researches and industrials in utilizing green rust.

• Journal of the Korean Chemical Society
• /
• v.66 no.2
• /
• pp.78-85
• /
• 2022

Natural white clay was treated with 6 M of H₂SO₄ and heated at 80℃ for 6 h under mechanical stirring and the resulting acid active clay was used as an adsorbent for the removal of Cs⁺ in water. The physicochemical changes of natural white clay and acid active clay were observed by X-ray Fluorescence Spectrometry (XRF), BET Surface Area Analyser and Energy Dispersive X-line Spectrometer (EDX). While activating natural white clay with acid, the part of Al₂O₃, CaO, MgO, SO₃ and Fe₂O₃ was dissolved firstly from the crystal lattice, which bring about the increase in the specific surface area and the pore volume as well as active sites. The specific surface area and the pore volume of acid active clay were roughly twice as high compared with natural white clay. The adsorption of Cs⁺ on acid active clay was increased rapidly within 1 min and reached equilibrium at 60 min. At 25 mg L^- of Cs⁺ concentration, 96.88% of adsorption capacity was accomplished by acid active clay. The adsorption data of Cs⁺ were fitted to the adsorption isotherm and kinetic models. It was found that Langmuir isotherm was described well to the adsorption behavior of Cs⁺ on acid active clay rather than Freundlich isotherm. For adsorption Cs⁺ on acid active clay, the Langmuir isotherm coefficients, Q, was found to be 10.52 mg g^-1. In acid active clay/water system, the pseudo-second-order kinetic model was more suitable for adsorption of Cs⁺ than the pseudo-first-order kinetic model owing to the higher correlation coefficient R² and the more proximity value of the experimental value q_e,exp and the calculated value q_e,cal. The overall results of study showed that acid active clay could be used as an efficient adsorbent for the removal of Cs⁺ from water.

• Journal of the Society of Disaster Information
• /
• v.18 no.1
• /
• pp.182-193
• /
• 2022

Purpose: By measuring and evaluating the risk of biodiesel through non-volatile residue (NVR) and flash point and explosion limit measurement at a specific temperature according to ASTM test standards, the risk of chemical fire causative substances is identified and a universal evaluation method By derivation and securing the risk-related data of the material, it can be used for the identification and analysis of the cause of the fire, and it can be applied to the risk assessment of other chemical substances Method: In order to measure the risk of biodiesel, it was measured using the non-volatile residue(NVR) measurement method, which measures how much flammable liquid is generated at a specific temperature. Heating was tested by applying KS M 5000: 2009 Test Method 4111. In addition, the flash point was measured using the method specified in ASTM E659-782005, and the energy supply method was measured using the constant temperature method. In addition, the explosion limit measurement was conducted in accordance with ASTM E 681-04 「Standard test method for concentration limits of flammability of chemicals(Vapors and gases)」 test standard. Result: As a result of checking the amount of combustible liquid by the non-volatile residue (NVR)measurement method, the non-volatile residue(NVR) of general diesel when left at 105±2℃ for 3 hours was about 30% (70% of volatile matter) and about 4% of biodiesel. In addition, similar results were obtained for the non-volatile residue(NVR)heating temperature of 150±2℃, 3 hours and 200±2℃ for 1 hour, and white smoke was generated at 200℃ or higher. In addition, similar values were obtained as a result of experimentally checking the explosion (combustion) limits of general diesel, general diesel containing 20% biodiesel, and 100% biodiesel. Therefore, it was confirmed that the flammability risk did not significantly affect the explosion risk. Conclusion: The results of this study suggested the risk judgment criteria for mixtures through experimental research on flammable mixtures for the purpose of securing the effectiveness, reliability, and reproducibility of the details of the criteria for determining dangerous substances in the existing Dangerous Materials Safety Management Act. It will be possible to provide reference data for the judgment criteria for flammable liquids that are regulated in the field. In addition, if the know-how for each test method is accumulated through this study, it is expected that it will be used as basic data in the research on risk assessment of dangerous substances and as a basis for research on the determination of dangerous substances.

• Research in Plant Disease
• /
• v.27 no.4
• /
• pp.172-179
• /
• 2021

This study aimed to assess the disease incidence and distribution of toxigenic in Korean triticale. The pathogen of triticale that cause Fusarium head blight were isolated from five different triticale cultivars that cultivated in Suwon Korea at 2021 year. The 72 candidate were classified as a Fusarium asiaticum by morphology analysis and by ITS1, TEF-1α gene sequence analysis. And the results of pathogenicity with 72 isolates on seedling triticale, 71 isolates were showed disease symptom. Also, seven out of 71 Fusarium isolates were inoculated on the wheat, to test the pathogenicity on the different host. The results showed more low pathogenicity on the wheat than triticale. The results of analysis of toxin type with 72 isolates, 64.6% isolates were produced nivalenol type toxin and other 4.6% and 30.8% isolates were produce 3-acetyldeoxynivalenol and 15-acetyldeoxynivalenol, respectively. To select fungicide for control, the 72 Fusarium isolates were cultivated on the media that containing four kinds fungicide. The captan, hexaconazole, and difenoconazole·propiconazole treated Fusarium isolates were not showed resistance response against each fungicide. However, six isolates out of 72 isolates, showed resistance response to fludioxonil. This study is first report that F. asiaticum causes Fusarium head blight disease of triticale in Korea.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.34 no.2
• /
• pp.37-45
• /
• 2022

A simplified model using the lifetime distribution has been presented to estimate the Mean Residual Life (MRL) of rubble-mound breakwaters, which is not like a stochastic process model based on time-dependent history data to the cumulative damage progress of rubble-mound breakwaters. The parameters involved in the lifetime distribution can be easily estimated by using the upper and lower limits of lifetime and their likelihood that made a judgement by several experts taking account of the initial design lifetime, the past sequences of loads, and others. The simplified model presented in this paper has been applied to the rubble-mound breakwater with TTP armor layer. Wiener Process (WP)-based stochastic model also has been applied together with Monte-Carlo Simulation (MCS) technique to the breakwater of the same condition having time-dependent cumulative damage to TTP armor layer. From the comparison of lifetime distribution obtained from each models including Mean Time To Failure (MTTF), it has found that the lifetime distributions of rubble-mound breakwater can be very satisfactorily fitted by log-normal distribution for all types of cumulative damage progresses, such as exponential, linear, and logarithmic deterioration which are feasible in the real situations. Finally, the MRL of rubble-mound breakwaters estimated by the simplified model presented in this paper have been compared with those by WP stochastic process. It can be shown that results of the presented simplified model have been identical with those of WP stochastic process until any ages in the range of MTT F regardless of the deterioration types. However, a little of differences have been seen at the ages in the neighborhood of MTTF, specially, for the linear and logarithmic deterioration of cumulative damages. For the accurate estimation of MRL of harbor structures, it may be desirable that the stochastic processes should be used to consider properly time-dependent uncertainties of damage deterioration. Nevertheless, the simplified model presented in this paper can be useful in the building of the MRL-based preventive maintenance planning for several kinds of harbor structures, because of which is not needed time-dependent history data about the damage deterioration of structures as mentioned above.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.1
• /
• pp.265-280
• /
• 2022

Hwangnyongsa Temple was the large Buddhist monastery of Silla that has existed for about 685 years. The temple underwent a series of excavations from 1976 to 1983, during which it was discovered that its layout consisted of one pagoda and three main dharma halls. This discovery also led to the production of four artistic depictions of the temple at various times from its foundation to its final phase. Previous studies on the architectural layout of Hwangnyongsa Temple are largely focused on the inner sanctuary ("Buddha's Land"). The studies on the temple's main architectural structures may be natural for those who are interested in the origins of and background to its establishment, but the studies on its outer sanctuary ("Sangha's Land") have to come first to acquire a deeper knowledge of the architectural layout of the temple as a whole. To gain a comprehensive understanding of the entire layout of Buddhist monasteries of the Silla dynasty, including both their inner and outer sanctuaries, the studies on Hwangnyongsa Temple are essential as it was once the kingdom's most highly honored temple. The studies on Korean Buddhist monasteries of the Three Kingdoms Period have produced only a limited amount of information concerning the outer sanctuary, resulting in little evidence about the exact scope of the temple's sanctuary. Meanwhile, the excavations of the Hwangnyongsa Temple site have revealed the archaeological features of the walls that divided the monastery and its neighboring facilities, thus helping to delineate the size of the temple site. The excavations have revealed the boundaries between the inner and outer sanctuaries of Hwangnyongsa Temple, as well as the entire temple precincts and the exterior, providing valuable information about the changes made to the layout of the temple. In this study, the main discussion focuses on the changes made to the sanctuary of Hwangnyongsa Temple during the Unified Silla and Goryeo Periods, particularly in relation to the architectural layout of the temple. The discussion is based on a review of the periods in which the Nammunji(South Gate site) was built, which provides tangible evidence about the expansion of the temple to the south, and the walls enclosing the temple precincts on the four sides and the changes that occurred afterwards. As a result, the study concludes that both the inner and outer sanctuaries of the temple probably changed through the 1 st and 3rd. It also concludes that the changes made to the architectural layout of Hwangnyongsa Temple were intended not only to alter the scope of the temple but were also closely associated with the politico-geographical significance of its location at the center of the royal capital of Silla and the urban archaeological remains around it.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.22 no.2
• /
• pp.69-79
• /
• 2020

In this study, the anti-inflammatory and cytotoxic effects of hot-water extracts from 10 kinds of macroalgae in Korea were investigated. It was selected materials in consideration of biological activity and industrial potential as follows: Caulerpa okamurae; Codium fragile; Ulva australis; Ishige foliacea; Saccharina japonica; Sargassum horneri; Undaria pinnatifida; Gloiopeltis tenax; Gracilaria verrucosa; Porphyra tenera. Results showed that S. japonica and G. tenax significantly decreased NO productionn in LPS-stimulated Raw 264.7 cells at concentrations of 100, 1000 ㎍/mL and 1000 ㎍/mL, respectively. However, most of the other macroalgae used in the experiment did not affect NO production. It was observed that all macroalgae extracts except for the highest concentration (1000 ㎍/mL) treatment group of P. tenera did not affect the viability in Raw 264.7 cells. In addition, there was not significant decrease in cell viability by macroalgae extracts treatment in HINAE cells. These results suggest that S. japonica and G. tenax could be used as potential safe natural anti-inflammatory agents for food and feed additives. Also, the results of this study are expected to be used as basic data for the development of functional materials for 10 kinds of macroalgae resources in Korea.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.23 no.2
• /
• pp.63-70
• /
• 2021

In order to compare and investigate the growth rates of each of the various soils, the soil mixing ratios were varied to four soils (Pitmos, Pearlite, Masato, General Soil, and Cocopeat). Ten were selected for each soil ratio and the average length and weight were compared. As a result, in the ratio of No. 1 pitmos 6.5: Perlite 2: Masato 1.5, it was measured as 16.36cm, 0.60g. In the ratio of No. 2 pitmos 10, 13.74cm, 0.41g. In the ratio of No. 3 general clay 10, it was measured as 12.43cm, 0.26g. 4 general clay 8, 0.39g. The growth rate of each soil was measured to be superior to that of other soil growth environments in the ratio of pitmos 6.5: pearlite 2: masato 1.5 soil. For ginseng plant analysis, 30 ginseng plants grown in the average length and weight of each soil at a ratio of 6.5: pearlite 2: masato 1.5 and relatively low-result general soil were selected and analyzed. As a result, 1,040ppm of nitrite nitrogen(NO₃-N) was higher in ginseng plants grown in general soil. There was no significant difference in phosphoric acid(P), potassium(K), and magnesium(Mg). Ginseng is characterized by poor growth when it exceeds 300ppm by combining ammonia tae (NH₄-N) and nitrate tae (NO₃-N) nitrogen. In addition, nitric acid produced in a part of this nitrite makes the pH reaction of the soil acidic, and the nitrite remaining in the soil evaporates into gas.

• The Journal of Korean Society for Radiation Therapy
• /
• v.33
• /
• pp.47-54
• /
• 2021

Purpose : In order to evaluate the usefulness of clinical application of the Pause & Resume methods by comparing and analyzing the data stability and dose reduction effect when repeat scan assuming irregular breathing and using the Pause & Resume method during chest 4D CT using Quasar^TM Phantom. Materials and Methods : Using the Quasar^TM Phantom, set the breathing rate per minute to 15 BPM and 7.5 BPM, and set the S15 point as an irregular breathing section, and then placed OSLD to this point and use the Pause & Resume method to measure the dose of S15. CTDIvol, DLP, and ALARA-CT were used for comparative analysis of radiation dose between Pause & Resume method and Repeat-scan. In order to evaluate the stability and usability of the data applying the Pause & Resume method, the captured images were sorted by Advanced Workstation Volume Share7 and then sent to Eclipse^TM, the diameter and volume were analyzed by forming a contour on the iron ball in the Quasar^TM Phantom Results : When using Pause & Resume, the dose of OSLD measurement increased by 1.97 times in the section of S15. As a result of image evaluation, the average value of all volumes measured with and without the Pause & Resume method at 15 BPM and 7.5 BPM was 15.2 cm3±0.5%.Allthemeasuredvaluesfor the radius of iron ball were 3.1 cm regardless of whether Pause & Resume method was used or not. In the case of using Pause & Resume, 33% decreased from the lowest DLP value and 38% decreased from the highest DLP value of repeat scan, and the effective dose also decreased 32.1% from the minimum value and 37.6% from the maximum value. Conclusion: Irradiation dose was increased by Pause & Resume method because of the repeat scan on the S15 site where assuming irregular breathing occurred, However Pause & Resume method led to a significant reduction in dose on overall scan range. It also proved the usefulness of clinical application of the Pause & Resume method as a result of similar diameters and volumes of iron ball measurement.