• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.1
• /
• pp.53-63
• /
• 2016

Wheel dynamometers are used to measure dynamic load that is conveyed from the road to a vehicle while driving. In this paper, two types of six-component wheel dynamometers utilizing shear deformation and bending deformation were designed and evaluated. Prior to designing the shear and bending type wheel dynamometers, the shear and bending deformation behaviors of the basic structure of the wheel dynamometer itself were analyzed using finite element analysis. Strain analysis was performed repeatedly in order to obtain a similar output sensing strain for each load component. The design was modified with a bridge circuit in order to minimize coupling strain. The results indicated that the shear type dynamometer was expected to obtain stable characteristics due to uniform strain distribution while the bending type dynamometer was expected to obtain high-quality sensitivity performance due to consistent output sensitivity.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.14 no.4
• /
• pp.273-279
• /
• 2011

Turbulent flow analysis around a wind turbine blade was performed to evaluate the power performance of offshore wind turbine. Fluent package was utilized to solve the Reynolds-averaged Navier-Stokes equations in non-inertial rotating coordinates. The realizable k-$\varepsilon$ model was used for turbulence closure and the grid system combining structured and unstructured grids was generated. In the first, lift and drag forces of 2-D foil section were calculated and compared with existing experimental data for the validation. Then torque and thrust of the wind turbine blade having NACA 4-series sections were calculated with fixed pitch angle and rpm. Tip speed ratio was varied by changing wind speed. In the next, three kinds of end plate were attached at the tip of blade in order to increase the power of the wind turbine. Among them the end plate attached at the suction side of the blade was found to be most effective. Furthermore, performance analysis with tilt angle and rake was also performed.

• Journal of Sensor Science and Technology
• /
• v.7 no.6
• /
• pp.401-408
• /
• 1998

A dual-channel automatic ac-dc voltage transfer error measurement system in which the output voltages of two thermal voltage converters which are ac voltage standard are directly measured at the same time to reduce the output voltage drift is described. Forward-reverse measurement method by using a two-channel scanner is used to cancel the offset voltage of the voltmeters. The agreements of the 4-V TVC comparison results between other national standards institute and Korea Research Institute of Standards and Science were less than about ${\pm}2\;ppm$ in the frequency range of $40\;Hz{\sim}100\;kHz$, and were less than about ${\pm}4\;ppm$ at $200\;kHz{\sim}1\;MHz$. Measurement uncertainty is reduced significantly from ${\pm}4\;ppm$ of manual system to ${\pm}3\;ppm$ of new system(up to 100 kHz) typically and great increase in comparison efficiency has been achieved by this system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.6
• /
• pp.592-597
• /
• 2005

The push pull forward converter is suitable in a low output voltage, a high output current applications with wide input voltage ranges. All magnetic components including output inductor, transformer and input filter can be integrated into single EI/EE core. The integrated push pull forward converter is considered through the comparison of efficiency according to the circuit parameters. The Nicera company's 5M FEE18/8/10C and NC-2H FEI32/8/20 cores are used for the transformer. The integrated push pull forward converter ratings are of $36\~72V$ input and 3.3V/30A output. In case that NC-2H FEI32/8/20 core used in the converter, the efficiency is measured up to $83.5\%$ at the switching frequency 200 kHz and the 11A load. The efficiencies of $76.4\%$ at a full load and $82.95\%$ at a half load are measured.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.1
• /
• pp.30-40
• /
• 2002

This paper studies the electronic ballast development for 250w MH lamps. We have improved the input power factor using a PFC IC. To provide the rating voltage required In the lamps, we have used the buck type dc-dc converter By this method, the stress of switching devices in inverter can be reduced. The inverter is the Full-Bridge type. To eliminate the acoustic resonance phenomena of MH lamps, we have added the high frequency sinewave voltage to the low frequency square-wave voltage to the lamp. We hove developed the igniter circuit using the L, C devices. We could control dimming of the lamp by varying the output voltage of the buck converter. The time of illuminating lamps and luminous intensity could be adjusted by season and time band. The buck converter output voltage can be controlled and the no load and over current situation were Protected by the development of the microprocessor Program.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.4
• /
• pp.117-122
• /
• 2021

Permanent magnet synchronous motors can secure high power density and efficiency, but have problems in that the materials required for manufacturing are expensive and design is somewhat more difficult than induction motors. Therefore, it is necessary to develop an optimal motor that considers both efficiency and maintenance convenience and related control research. In addition, driving by a practical motor leads to a request to increase the highest efficiency in a narrow rated range, an increase in average efficiency in the entire electric driving range, and an increase in average output. Due to this movement, a reluctance motor that does not require a permanent magnet is being considered as an alternative. In this paper, in line with the issues of the times that require the development of future technology that can replace rare earth permanent magnet motors and the technological preemption of rare earth reduction motors and rare earth motors, switched reluctance motors without permanent magnet For motor, SRM), modeling through machine language (C language) and the characteristics of SRM accordingly are to be studied.

• Korean Journal of Agricultural Science
• /
• v.20 no.2
• /
• pp.167-180
• /
• 1993

Most of small size diesel engines are widely used with the same size and weight flywheel in the levels of 6.0kW and 7.5kW. This study was conducted to obtain basic data which affect the engine performance of the power tiller. The flywheel weight was considered as a major factor in this research. Basically, fuel consumption ratio, motoring loss, torque, vibration and mechanical efficiency of the engine were measured and analyzed on four levels of flywheel weight, 32.2, 29.4, 26.2 and $24.2kg_f$, respectively. Results were obtained as follows: 1. The weights of flywheel were $23.7kg_f$ from design program of JSME and $24.5kg_f$ from ASME and SAE design criteria. Therefore, the flywheel weight of $32.2kg_f$ might be reduced about $8kg_f$ in 7.5kW engine. 2. The rated outputs of 6.0kW and 7.5kW engine were actually 7.43kW and 7.85kW, respectively. When flywheel weight was reduced from $32.2kg_f$ to $24.2kg_f$, outputs were increased from 7.43kW to 7.70kW in 6.0kW engine and from 7.85kW to 8.25kW in 7.5kW engine. 3. When the flywheel weight was reduced from $32.2kg_f$ to $24.2kg_f$, fuel consumption ratio was decreased from 300.8 to 296.8g/kW-hr in 6.0kW engine and also from 313.6 to 312.8g/kW-hr in 7.5 kW engine, respectively. 4. When the flywheel weight was reduced from $32.2kg_f$ to $24.2kg_f$, mechanical efficiency of engine was increased from 76.1% to 76.8% in 6.0kW engine and also from 76.7% to 77.0% in 7.5kW engine, respectively. 5. When the flywheel weight was reduced from $32.2kg_f$ to $24.2kg_f$, vibration was decreased at X-axis and Z-axis in 6.0kW engine, however, slightly increased at Y-axis in 6.0kW engine and at all axes in 7.5kW engine. 6. When the flywheel weight was reduced from $32.2kg_f$ to $24.4kg_f$ motoring loss was decreased from 2.33kW to 1.75kW in 6.0kW engine and also from 2.46kW to 1.84kW in 7.5kW engine.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.5
• /
• pp.529-536
• /
• 2013

Most serious stroke patients have the paralysis on their wrists, and can't use their hands freely. But their wrists can be recovered by rehabilitation exercises. Recently, professional rehabilitation therapeutists help stroke patients exercise their wrists in hospital. But it is difficult for them to rehabilitate their wrists, because the therapeutists are much less than stroke patients in number. Therefore, the wrist twist-exercise rehabilitation robot that can measure the twist force of the patients' wrists is needed and developed. In this paper, the six-axis force/moment sensor was designed appropriately for the robot. As a test result, the interference error of the six-axis force/moment sensor was less than 0.85%. It is thought that the sensor can be used to measure the wrist twist force of the patient.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.4
• /
• pp.309-316
• /
• 2016

In this study, we described the design of a three-axis force/torque sensor for measuring the force and torque in a lower-limb rehabilitation robot. The three-axis force/torque sensor is composed of Fx force sensor, Fz force sensor and Tz torque sensor. The sensing element for Fx force sensor and Tz torque sensor is used in a two-step parallel plate beam, and that of Fz force sensor is used in a parallel plate beam. The rated loads of Fx force sensor, Tz torque sensor and Fz force sensor are 300 N, 15 N m and 100 N, respectively. The three-axis force/torque sensor was designed using the finite element method, and manufactured using strain-gauges. The three-axis force sensor was further characterized. As a result, the interference error of the three-axis force/torque sensor was < 1.24%, the repeatability error of each sensor was < 0.03%, and the non-linearity was < 0.02%.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.282-283
• /
• 2011

전압이 정격전압을 유지하지 못하면 전기기기의 효율 저하, 수명단축, 손실증대를 야기 시킨다. 하지만 더 큰 문제는 예기치 못한 사고 및 급격한 부하 증가에 따라 전압이 떨어질 때 생길 수 있는 전압붕괴 현상이다. 전압 붕괴 현상은 대규모로 퍼져 대정전 사태를 초래 할 수 있다. 전압안정도를 유지하고 향상시키기 위해 적절한 무효전력의 공급 및 무효전력 예비력 확보는 매우 중요하다. 무효전력 공급을 위한 설비에는 병렬 커패시터, 발전기 등이 있다. 하지만 병렬 커패시터 등 조상설비는 이미 설치되어 있는 양만큼만 출력을 낼 수 있고 사고 등의 급격한 계통변화에 빠르게 대응 할 수 없다. 즉, 사고나 급격한 부하 증가에 효율적으로 대응하기 위한 수단으로 발전기 순동 무효 예비력의 확보가 필수적이다. 하지만 무효전력은 지역적 특성을 띄고 있다. 그렇기 때문에 예비력의 확보와 더불어 지역적 특성을 반영해야만 하다. 본 논문에서는 발전기 무효전력 예비력 관점에서 무효전력의 지역적 특성을 고려 국내지역별 발전기 무효전력 예비력 산정을 위한 발전기 선정을 목표로 한다.