• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.5
• /
• pp.431-437
• /
• 2018

The running attitude of a planing hull is determined by the pressure distribution on the hull bottom, and it significantly affects hydrodynamic performance of the ship, i.e., resistance, maneuverability, and seakeeping ability. Therefore, it is essential to investigate pressure distribution on the hull bottom in order to improve hull design. In the present study, a novel pressure measurement system using tactile sensors was introduced for a planing hull. The test model was a 23 m-class planing hull with a hard chine. The pressure measurement showed that the pressure at the transom was lower than the atmospheric pressure, owing to flow separation at the transom.

• Geotechnical Engineering
• /
• v.3 no.2
• /
• pp.7-16
• /
• 1987

The dynamic properties of soils are affected by parameters like, gradation characteristics, void ratio, confining pressure, etc. . This study mainly investigated experimentally the effect of gradation on the dynamic properties of sands with the effect of void ratio and confining pressure. Test results showed that shear modulus/damping ratio was increased/decreased with the decrease of void ratio and with the increase of confining pressure. When the fine content increased, shear modulus/damping ratio was decreased/increased. This study explained this phenomenon by the concept of the "effective number of contacts" and the "dead space".ot;dead space".uot;.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.436-439
• /
• 2008

Computer simulation of multiphase flows has grown dramatically in the last two decades. In this work, we have studied the flow characteristics of immiscible two fluids in a 2-D micro channel driven by pressure gradient using multi-phase lattice Boltzmann method suggested by Shan and Chen(1993) considering the fluid-surface interaction. we tried to examine the effects of parameters related to the two phase flow characteristics and pressure drop in the micro channel like contact angle and channel configuration by changing their value. The results of current study could show the lattice Boltzmann method can simulate the behaviors of two phase flow in the region of micro fluidics well.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1994.03a
• /
• pp.53-77
• /
• 1994

기체 분리 방법의 종류 일반적으로 기체를 분리하는 방법에는 다음과 같이 3가지 종류가 있다. Cryogenic Separation (심냉분리법) : 기체를 압축, 냉각, 액화 시킨후 boiling point 차이를 이용한 증류볍으로 분리하는 방법을 말하며 기체 분리 기술중 가장 오래된 기술이다. Adsorption (흡착법) - PSA : 분리 하고자 하는 기체를 흡착제에 흡착 시키고 흡착되지 않는 잔류 기체는 다른 용리에 이송한 후 흡착된 기체를 온도차, 압력차 등을 이용하여 탈착 시키면서 기체를 분리하는 방법이다. Membrane Separation (막분리법) : 특수하게 제작된 막의 한쪽면으로기체 (여러 종류의 기체분자로 구성된 혼합기체)가 접촉되어 막 반대면의 압력이 저압 상태로 될때 혼합기체증의 특정기체가 막을 투과하는 현상을 이용하여 분리하는 방법을 말하며 이때에 투과현상은 막과 친화성이 좋은 특정기체분자가 압력차를 Driving Force로 하여 막의 표면에 용해 되고 이어서 막 내부에서 농도구배에 의한 확산이 일어나고 다른면에서 탈착 되어지는 원리이다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.3950-3960
• /
• 2014

In this study, the drag forces on a submerged square cylinder were analyzed using a three dimensional hydrodynamic model. The numerical results were compared with the experimental results to check the reliability of the numerical simulations, and the characteristics of the drag forces with the relative depths were analyzed by analyzing the pressure acting on the cylinder surface, which are normally difficult to measure experimentally. The numerical results showed that the drag forces acting on a submerged square cylinder originate mainly from the pressure forces, and component of the shear forces decreased with increasing relative depth. The pressure coefficient distributions showed that in the case of a low relative depth, a relatively high pressure was formed in the front of a cylinder, and a relatively low pressure was formed in the rear, which gives a high drag coefficient. In a high relative depth, the pressure in the front decreased and pressure in the rear increased, which is a similar phenomenon to that normally observed in two dimensional square cylinder flow. The effect of the static pressure was analyzed and the surface elevation difference between the front and rear zone of a cylinder has a limited effect on the drag forces. Finally, the numerical results showed that the drag forces acting on a submerged square are dominated by the dynamic pressure formed by three dimensional flow and the distribution of local surface elevation.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.20 no.1
• /
• pp.50-54
• /
• 1983

Contact resistance variation which may be called sliding noise in carbon film variable resistors whose resistance elements consists of linear resistivity distribution were measured with several kinds of sliders and were analyzed to reduce the contact resistance variation. About the measuring method, the standard method of measuring contact resistance variation specified by the variable Resistance Components Institute was adupted. By analyzing the experimental results, it has been shown that the primary cause of contact resistance variation is due to current constriction and small discharge sparks in the resistance film in the area close to the slide contact. Moreover, it has been found that the sliding noise would be reduced by increasing the number of contact points, sliding speed, and pressure, and by using some kinds of insulation oil on the contacting surface. High contact resistance variation is likely to occur in the area of high resistance variation in a logrithmic resistance taper.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.2
• /
• pp.139-146
• /
• 2011

The breaking wave pressure occurs when a plunging breaker instantaneously impinges on structural surface, and appears differently depending on whether or not to form air pockets at the instant of contact. The Wagner type normally forms a single pressure peak at the contact spot due to the direct collision of water volume to the structure whereas in the Bagnold type the time lagged oscillation of the air pocket causes pressure peaks even at areas away from the spot. In the present study, the Bagnold's impact pressure is numerically and experimentally investigated for the bulkhead of an underwater tunnel under construction which is subjected to nearby breaking waves. A numerical solver of Navier-Stokes equations was applied to reproduce the breaking waves near a bulkhead, and the results showed the Bagnold's impact pressure occurring on the back (land side) face of the bulkhead. The existence of the impact pressure was also verified by a hydraulic model testing, and it was found that the experimental results well conformed to their numerical counterparts.

• Explosives and Blasting
• /
• v.22 no.4
• /
• pp.7-15
• /
• 2004

An explosion modeling technique was developed by using the spherical discrete element code, PFC3D, which can be used to model the dynamic stress wave propagation phenomenon. The modeling technique is simply based on an idea that the explosion pressure should be applied to a PFC3D particle assembly not in the form of an external force (body force), but in the form of a contact force (surface force). According to this concept, the explosion pressure is applied to the wall particles by the scheme of radius expansion/contraction of inner-hole particles. The output wall force is compared to the input hole pressure in every time step, and a correction routine is activated to control the radius multiplier of the inner-hole particles. A comparative blast simulation far a cement mortar block of $80\times90\times80mm$ was conducted by using the conventional explosion modeling method and the new one. The results of the simulation are presented in a qualitative fashion.

• Membrane Journal
• /
• v.17 no.4
• /
• pp.345-351
• /
• 2007

In this research, by using the fluorine gas, the poly(ether sulfone) (PES), the polysulfone (PSf), and the poly-vinylidenefluoride (PVDF) membranes were modified to improve the performance of the optional Gas-Liquid Contactor The SEM, surface contact angle, XPS, and the water transmission minimum pressure test was performed in order to examine the characteristics of which is surface modified. As a result of looking into the surface morphology of from the SEM measurement, we could know that the roughness of the membrane surface increased as the fluorine processing time increased. $-CH_2$, and the perfluoro group of $-CH_3$ were chemically combined with the surface fluorine conversion film surface and the hydrophobicity was exposed to be increased. Moreover, we could know that as the surface fluorinated processing time increased from the surface contact angle and water transmission minimum pressure test, the measured value increased and the overall characteristics were improved.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.6
• /
• pp.533-539
• /
• 2009

In this study, the femur, the tibia, the articular cartilage and the menisci are three dimensionally reconstructed using MR images of healthy knee joint in full extension of 26-year-old male. Three dimensional finite element model of the knee joint is fabricated on the reconstructed model. Also, the FE models of ligaments and tendons are attached on the biologically suitable position of the FE model. Bones, articular cartilages and menisci are considered as homogeneous, isotropic and linear elastic materials, and ligaments and tendons are modeled as truss element and nonlinear elastic springs. The numerical results show the contact pressure and the von Mises stress distribution in the soft tissues such as articular cartilages and menisci which can be regarded as important parameters to estimate the failure of the tissues and the pain of the patients.