• 한국소음진동공학회논문집
• /
• 제25권9호
• /
• pp.606-613
• /
• 2015

In this study, the torsional vibration analysis for a marine propulsion system is carried out by using the transfer matrix method(TMM). The torsional moment produced by gas pressure and reciprocating inertia force may yield severe torsional vibration problem in the shaft system which results in a damage of engine system. There are several ways to control the torsional vibration problem at hand, firstly natural frequencies can be changed by adjusting shaft dimensions and/or inertia quantities, secondly firing order and crank arrangement are modified to reduce excitation force, and finally lower the vibration energy by adopting torsional vibration damper. In this paper, the viscous torsional vibration damper is used for reducing the torsional vibration stresses of shaft system and it is conformed that optimum model of the viscous damper can be determined by selecting the geometric design parameters of damper and silicon oil viscosity.

• Journal of Advanced Marine Engineering and Technology
• /
• 제20권4호
• /
• pp.50-58
• /
• 1996

The torsional vibration of the propulsion shafting system equipped with viscous damper is investigated. The equivalent system is modeled by a two mass softening system with Duffing's oscillator and the vibratory motion is described by non-linear differential equations of second order. The damper casing is fixed at the front-end of crankshaft and the damper's inertia ring floats in viscous silicon fluid inside of the camper casing. The excitation frenquency is proportional to the rotational speed of engine. The steady state response of the equivalent system is analyzed by the computer and for this analyzing, the harmonic balance method is adopted as a non-linear vibration analysis technique. Frequency response curves are obtained for 1st order resonance only. Jump phenomena are explained. The discriminant for the solutions of the steady state response is derived. Both theoretical and measured results of the propulsion shafting system are compared with and evaluated. As a result of comparisions with both data, it was confirmed that Duffing's oscillator can be used in the modeling of the propulsion shafting system attached with viscous damper with non-linear stiffness.

• Journal of Advanced Marine Engineering and Technology
• /
• 제20권4호
• /
• pp.372-372
• /
• 1996

The torsional vibration of the propulsion shafting system equipped with viscous damper is investigated. The equivalent system is modeled by a two mass softening system with Duffing's oscillator and the vibratory motion is described by non-linear differential equations of second order. The damper casing is fixed at the front-end of crankshaft and the damper's inertia ring floats in viscous silicon fluid inside of the camper casing. The excitation frenquency is proportional to the rotational speed of engine. The steady state response of the equivalent system is analyzed by the computer and for this analyzing, the harmonic balance method is adopted as a non-linear vibration analysis technique. Frequency response curves are obtained for 1st order resonance only. Jump phenomena are explained. The discriminant for the solutions of the steady state response is derived. Both theoretical and measured results of the propulsion shafting system are compared with and evaluated. As a result of comparisions with both data, it was confirmed that Duffing's oscillator can be used in the modeling of the propulsion shafting system attached with viscous damper with non-linear stiffness.

• 한국전산구조공학회논문집
• /
• 제30권4호
• /
• pp.313-318
• /
• 2017

본 연구는 진동에너지를 흡수하기 위한 진동 금속 댐퍼의 구조 해석과 최적 설계를 수행한다. 고무 베어링, 마찰 또는 점성 댐퍼와 같은 다른 댐퍼와는 달리 이 금속제진장는 금속의 소성 변형과 그에 따른 히스테리시스 현상을 이용하여 구조물의 진동을 감소시킨다. 이 금속제진장치를 최적화 하려면 댐퍼를 통해 소성 변형을 얻는 것이 중요하다. 금속제진장치의 최적화된 형상을 찾기 위해 형상 최적화 방법을 적용하였다. 또한 매개 변수화 체계에 따라 일부 최적의 모양을 찾을 수 있다.

• 한국가스학회지
• /
• 제13권6호
• /
• pp.1-8
• /
• 2009

본 연구는 웻지 시스템을 이용하여 3축 방향의 진동 및 충격을 완화시킬 수 있는 감쇠기에 관한 것이다. 기존의 수직방향 진동/충격에 대해서만 흡진하는 디스크 스프링 완충기를 개선하여 웻지를 추가함으로써 종 방향은 물론 횡 방향을 모두 포함한 3축에 대해 흡진이 가능한 댐퍼를 제안하였다. 수학적 모델을 수립하여, 댐퍼내의 중요한 요소로 작동하는 디스크 스프링과 웻지의 특성을 고찰하였으며, 실험을 통해 댐퍼의 거동을 고찰하였다. 수치 해석 결과와 실험 결과가 잘 일치함을 알 수 있었고, 소산된 에너지양을 구한 후, 수직 수평방향에 대한 등가 점성 감쇠를 구하였다.

• 한국지진공학회논문집
• /
• 제9권1호통권41호
• /
• pp.51-59
• /
• 2005

본 연구에서는 위의 어려움을 해결하기 위해, 스마트 수동제어 시스템을 제안하였다. 스마트 수동제어 시스템은 MR댐퍼와 EMI시스템으로 구성되며, EMI시스템은 영구자석과 솔레노이드 코일로 이루어진다. EMI시스템은 MR댐퍼의 왕복운동에너지를 전기에너지로 변환하므로, 스마트 수동제어 시스템은 외부 전원 없이 외부하중에 따라 댐퍼의 점성을 바꾸는 적응성을 갖는다. 따라서 간단하고 효율적인 장치로써, 대형토목구조물에 적용 가능하다. 이의 확인을 위해 예제를 통한 수치해석을 수행하였으며, 스마트 수동제어 시스템이 강진에 대해서는 기존의 반능동 제어 MR댐퍼 시스템 보다 우수한 성능을 보인다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2011년도 정기 학술대회
• /
• pp.454-457
• /
• 2011

본 논문에서는 국내에서 아직 기준이 마련되지 않은 제진설계에 대한 접근을 소개하였다. ASCE 7-05 기준에 근거하여 국내 5층 규모의 철근콘크리트 신축 건물에 제진 설계를 수행하였다. 우리나라의 현행 기준을 만족하면서 효과적인 제진 시스템 설계를 위한 방법을 소개한다. ASCE 7-05 기준에서는 제진 구조물 해석 시 부재력이 공칭강도의 1.5배를 초과하지 않은 경우 경계비선형 해석을 허용하고 있다. 이 때의 제진 설계 프로세스는 기존의 중력하중 및 등가정적하중의 75%에 의한 단면을 가정하여 부재설계를 실시하고, 선형 시간이력 해석을 통해 제진장치 및 가새를 설계한다. 이후 우리나라 실정에 맞도록 보정된 인공 지진파를 입력하여 경계비선형 해석을 실시하고, 밑면 전단력 및 층간변위 등의 만족여부를 검토한다. 이 때 목표성능을 완전탄성설계 또는 유사탄성설계로 정하여 목표성능을 만족하는지도 검토하여야 한다. 본 논문에 적용한 신축 건물은 유사탄성 설계를 위해 경계비선형 해석을 실시하였고, 가장 효과적인 제진 설계를 위해 댐퍼의 종류, 설치방법, 개수, 변위 증폭비 등을 변수로 한 case study를 진행하였다. 해석 결과 목표성능을 만족하는 범위 내에서 가장 효과적인 제진 설계는 점성댐퍼, 이층 토글형태, 증폭비 2.0, 총 8개의 댐퍼를 설치하는 것으로 나타났다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.586-590
• /
• 2006

This paper presents a new vibration control device by which the mass and damping of a structure is increased equivalently. The vibration control system, named toggle-rotational inertia-viscous damper, can be utilized effectively in applications of small structural drift. Numerical analysis shows that because the relative drift of a structure can be effectively amplified by the toggle system, the device has a great performance in the vibration control without the increase of the damper capacity and size. It is also observed that vibration control effects is caused by the increase of equivalent mass and damping due to the rotational inertia and damping of the device.

• Journal of Advanced Marine Engineering and Technology
• /
• 제13권1호
• /
• pp.77-96
• /
• 1989

In diesel engines, it is inevitable that the torsional vibration is produced by the fluctuation of engine torque. Therefore, if the occurence of torsional vibration is confirmed in the design stage or the torsional vibration is observed on the bed of test run, it is necessary to establish some preventive measures to avoid dangerous conditions. Major preventive measures are as follows : 1. Changing the natural frequency of shaft system. 2. Repressing the vibration amplitude by the damping energy. 3. Counterbalancing the exciting torque by the resistant torque. 4. Counterbalacing the harmonic component of exciting energy. In above methos, the damper is the last measure to be used for controlling the torsional vibration. In this thesis, the design of viscous damper that absorbs the exciting energy is investigated and a number of problems associated with the design of viscous damper are treated and a computer pregram for the process of damper design is developed. A viscous damper for a high speed diesel engine is designed and its effect is simulated by the author's computer program.

• Journal of Advanced Marine Engineering and Technology
• /
• 제15권2호
• /
• pp.44-52
• /
• 1991

The crankshaft system of engine is a complex vibratory object and its vibration modes are consisted of torsional, axial and their coupled vibration. Among them, the torsional vibration causes engine noise as well as serious fatigue faillures of crankshaft. If the troules of noises and crankshaft strength are forecasted by torsional vibration calculation in the design atage of crankshaft, the torsional damper is adopted as the final countermeasure. In this paper, some computer program to calculate crankshaft torsional vibration of engine are developed and with developed programs, an efficient rubber-viscous damper for automobile and with developed programs, an efficient rubber-viscous damper for automobile engine is designed and manufactured, and then it is fitted on the actual automobile engine to confirm its calculated efficiency. By comparing the measured result (with damper and without damper) with the calculated one, the reliability of developed computer programs and the performances of manufactured damper are confirmed.