• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.5 s.347
• /
• pp.11-16
• /
• 2006

This paper reports the correlation between dielectric constant and degree of amorphism of the hybrid type SiOC thin films. SiOC thin films were deposited by high density plasma chemical vapor deposition using bistrimethyl- silylmethane(BTMSM,$H_{9}C_{3}-Si-CH_{2}-Si-C_{3}H_{9}$) and oxygen precursors with various flow rate ratio. As-deposited film and annealed films at $400^{\circ}C$ were analyzed by XRD. The SiOC thin films were amorphous from XRD patterns. For quantitative analysis, the diffraction pattern of the samples was transformed to radial distribution function by Fourier analysis, and then compared with each other. The degree of amorphism of annealed films was higher than that of as-deposited ones. The dielectric constant varied in accordance with flow rate ratio of precursors. The lowest dielectric constant was obtained from the as-deposited film which has the highest degree of amorphism after annealing.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.41-44
• /
• 2008

Fiber Reinforced Polymers (FRPs) have recently been highly used for repairing and strengthening civil structures due to their superior material properties. By using FRPs, external bond method is the most used method in the construction industry. Although many researches on reinforced concrete externally strengthened with FRPs have been conducted, time-dependant behaviors of the beams have not been investigated yet. This paper documents a series of beam experiments that were carried out to evaluate time-dependant behavior. Three RC beams were built and the parameters considered in this experiment were types of FRPs. Through these experiments, it was proved that the beam strengthened with CFRP was more effective than that with GFRP in terms of time-dependant behavior.

• Journal of the Korean Vacuum Society
• /
• v.18 no.1
• /
• pp.24-29
• /
• 2009

The SiOC film as inter layer insulator was researched the reason of the decreasing the dielectric constant by the ionic polarization and electronic polarization, respectively. The dielectric constant was measured using the conventional C-V measurement system, and the reflective index owing to the electronic polarization. Two kinds of dielectric constants were compared and then induced the origin of low-k materials. The chemical properties of the SiOC film were analyzed by the FTIR spectra, and the carbon content was obtained by the deconvoluted data of FTIR spectra. The variation of the carbon content tended to similar to the trend of reflective index, but was in inverse proportion to the dielectric constant. The effect of the electronic polarization did not affect the decreasing the dielectric constant, however the ionic polarization decreased effectively the dielectric constant of the SiOC film.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.139-139
• /
• 1999

다이아몬드는 지구상에서 가장 단단한 물질로 잘 알려져 있을 뿐만 아니라 공업적 측면에서 볼 때, 여러 가지 특출한 성질들을 동시에 지니고 있다. 인장강도, 압축강도, 탄성계수 등 기계적 특성이 우수하고 넓은 광투과성과 내열, 내화학, 내방사성을 지니고 있으며, 열전도율이 높고 전기적으로 절연체이다. 또한 hole이동도가 높고 도핑에 의해서 반도체적 특성을 나타낸다. 이와 같이 매우 뛰어난 성질을 공업적으로 응용하기 위하여 이전부터 많은 연구가 행해져 왔으며, 1980년대에 들어와 박막이나 코팅 형태로의 합성이 가능한 기상합성법이 큰 발전을 보임으로써 다이아몬드의 우수한 특성을 여러 분야에서 폭넓게 응용할 수 있게 되었다. 특히 마찰 응용분야에 최적의 재료로 추천되고 있다. 지금도 Epitaxial 다이이몬드를 기지 위에 성장시키고 다결정질박막을 여러 가지 비다이아몬드(Si, W, Mo 등) 기지 위에 성장시키는 연구가 계속되고 있으며 공구강 위엥 경질코팅으로써 한층 개선된 다이아몬드박막 제조를 위한 수많은 연구노력들이 집중되고 있다. 그러나 일반탄소강에 다이아몬드박막을 성장시키기 위한 많은 노력들은 크게 바람직하지 않은 non-diamond carbon(black carbon or graphitic soot)의 형성 때문에 방해를 받고 있다. 계면에서 이들의 형성은 증착된 다이아몬드박막과 금속기지의 저조한 밀착력을 나타내게 된다. 이외 같이 다이아몬드박막의 응용을 위하여 다이아몬드피막에 요구되는 중요한 조건은 기지에 대해서 강한 밀착력을 나타내는 것이며, 동시에 상대물에 대하여 낮은 마찰계수를 가져야 한다. 그러나 다이아몬드와 금속기지는 서로 다른 열챙창계수(각각 0.87$\times$10-6K-1, 12$\times$10-6K-1)의 차이로 인하여 밀착력이 현저히 떨어진다는 단점으로 인해 산업화에 많은 제약을 받아왔다. 이러한 문제점을 해결하기 위하여 본 연구에서는 다이아몬드박막과 금속기지 사이에 중간층을 이용하는 방법을 제안하였다. 이러한 시도는 일반적으로 중간층 형성 금속인 Ti 또는 TiN 등이 적용되었으나 원하는 결과를 얻지 못하였다. 즉 carbon과 Fe의 상호확산, non-diamond carbon상의 형성 그리고 열잔류응력을 완화시키고 일반탄소강 위에 다이아몬드박막을 형성시켜 우수한 밀착력을 얻기 위한 목적에 미흡하였던 것이다. 이에 중간층으로 Cr 또는 Cr계 화합물 박막을 이용하였는 바, 이 중간층을 이용한 결과 우수한 밀착력을 나타내는 다이아몬드박막을 얻었으며 열적, 구조저으로 모재와 다이아몬드에 적합한 결과를 얻을 수 있었다. 본 연구에 의해 얻어진 결과들은 재료 가공을 위하여 높은 경도와 내마모성등이 요구되는 절삭공구나 금형의 수명 향항에 크게 기여할 것이며 산업적으로 큰 응용이 기대된다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.4
• /
• pp.373-379
• /
• 2002

We investigated the evolution of magnetoresistance and magnetic property of tunneling magnetoresistive(TMR) device with microstructure and plasma oxidation time. TMR devices have potential applications for non volatile MRAM and high density HDD reading head. We prepared the tunnel magnetoresistance(TMR) devices of Ta($50{\AA}$)/NiFe($50{\AA}$)/IrMn($150{\AA}$)/CoFe($50{\AA}$)/Al($13{\AA}$)-O/CoFe($40{\AA}$)/FiFe($400{\AA}$)/Ta(($50{\AA}$) structure which have $100{\times}100\mu\textrm{m}^2$ junction area on $2.5{\times}2.5\textrm{cm}^2$ Si/$SiO_2$(($1000{\AA}$) substrates by an inductively coupled plasma(ICP) magnetron sputter. We fabricated the insulating layer using an ICP plasma oxidation method by with various oxidation time from 30 sec to 360 sec, and measured resistances and magnetoresistance(MR) ratios of TMR devices. We found that the oxidized sample for oxidation time of 80 sec showed the highest MR radio of 30.31 %, while the calculated value regarding inhomogeneous current effect indicated 25.18 %. We used transmission electron microscope(TEM) to investigate microstructural evolution of insulating layer. Comparing the cross-sectional TEM images at oxidation time of 150 sec and 360 sec, we found that the thickness and thickness variation of 360 sec-oxidized insulating layer became 30% and 40% larger than those of 150 sec-oxidized layer, repectively. Therefore, our results imply that increase of thickness variation with oxidation time may be one of the major treasons of the MR decrease.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.1
• /
• pp.53-59
• /
• 1999

The ceramic capacitor was fabricated by $(Ba_{0.85}Ca_(0.15)TiO_3+ZnO$ + ZnO(from 0.1 to 0.4 mol ratio). The electrical and structural properties of ceramic capacitor for high voltage application was studied in this study. The relative rensity of ceramics capacitor has shown high in all specimen. The grain was a small size from $1.0[\mum]$ to $1.22[\mum]$ and it was increased with ZnO at 0.3 mol ratio. It was stabilized that the temperature coefficient of ceramic capacitor to change temperature had below 100[ppm] at 0.12~10[kHz]. The dielectric reIaxation time was decreased by interface polarization over $110[^{\circ}C]$ and it was increased by space polarization of paraelectric layer below $110[^{\circ}C]$. The insulating layer was increased with ZnO and dielectric constant to voltage was stabilized by 0.1[%].0.1[%].

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.3
• /
• pp.80-86
• /
• 2003

A study on the insulation aging assessment and maintenance for submarine medium voltage power cable systems has been performed The purpose of this work is the economic discrimination and maintenance of bad cables which is likely to cause cable system failure. 1 have found that aging status of submarine cable systems are very poor and in progress. Therefore, we have the replacement of cable terminations and repeat the diagnostic measurement Insulation status were improved with the replacement of cable terminations. I have confirmed, with the electrical md structural analysis of terminations, that the poor aging status of cables are mainly caused not by the cable insulations but by the aging of cable terminations. From the above results, I have also confirmed that the domestic diagnostic system is successful and convenient for the discrimination and maintenance of the damaged cables economically.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.865-868
• /
• 2005

We fabricated the $Pb_{0.72}La_{0.28}TiO_3 (PLT(28))$ thin film successfully by using the sol-gel method and characterized it to evaluate its potential for being utilized as the capacitor dielectrics of ULSI DRAMs. In our sol-gel process, the acetates were used as the starting materials. Through the TGA-DTA analysis, we established the excellent fabrication conditions of the sol-gel method for the PLT(28) thin film. We obtained the dense and crack-free PLT(28) thin film of 100% perovskite phase by drying at 350$^{\circ}C$ after each coating and final annealing at 650$^{\circ}C$. Electrical properties of PLT(28) thin film were measured through formation on the Pt/Ti/SiO$_2$/Si substrate and its dielectric constant and leakage current density were measured as 936 and 1.1${\mu}$A/cm$^2$, respectively

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.12
• /
• pp.1122-1127
• /
• 1998

Group II-AF_2$films such as $CaF_2$, $SrF_2$, and $BaF_2$ have been commonly used many practical applications such as silicon on insulatro(SOI), three-dimensional integrated circuits, buffer layers, and gate dielectrics in filed effect transistor. This paper presents electrical and structural properties of fluoride films as a gate dielectric layer. Conventional gate dielectric materials of TFTs like oxide group exhibited problems on high interface trap charge density($D_it$), and interface state incorporation with O-H bond created by mobile hydrogen and oxygen atoms. To overcome such problems in conventional gate insulators, we have investigated $CaF_2$ films on Si substrates. Fluoride films were deposited using a high vacuum evaporation method on the Si and glass substrate. $CaF_2$ films were preferentially grown in (200) plane direction at room temperature. We were able to achieve a minimum lattice mismatch of 0.74% between Si and $CaF_2$ films. Average roughness of $CaF_2$ films was decreased from 54.1 ${\AA}$ to 8.40 ${\AA}$ as temperature increased form RT and $300^{\circ}C$. Well fabricated MIM device showed breakdown electric field of 1.27 MV/cm and low leakage current of $10^{-10}$ A/$cm^2$. Interface trap charge density between $CaF_2$ film and Si substrate was as low as $1.8{\times}10^{11}cm^{-2}eV^{-1}$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.1
• /
• pp.89-98
• /
• 2002

Optical current sensor and optical voltage sensor modules were designed and fabricated to improve measurement error and insulation in automatic power distributor By using Faraday effect, optical current sensor with an $\alpha$-iron core was designed and fabricated to minimize current induction of the other phase and was optimized to maintain linearity. Optical voltage sensor was fabricated owing to the pockets effect and adopted spatial electric field type because of small room in an automatic power distributor. To connect a distributor with an external terminal for signal processing, optical multi connector was designed, fabricated and tested for coupling loss and gas leakage. The linearity of optical current sensor for applied current maintains variation of smaller than 2.5% for applied current range from 20A to 700A. The linearity of optical voltage sensor was smaller than 1% for appling voltage from 6.6kV to 19.8kV. Since the measured characteristics are good, these devices can be considered as being applicable in practice.