• Clean Technology
• /
• v.8 no.3
• /
• pp.119-128
• /
• 2002

In the present study the membrane filtration characteristics of a commercially available synthetic water-based cutting oil through two kinds of ultrafiltration membranes (HF1-45-CM50 and HF1-43-CM100) with molecular weight cut-offs of 50,000 and 100,000, respectively, have been investigated in detail. Among these membranes, the hydrophilic one (HF1-45-CM50) was found to show a satisfactory result for both the permeate flux and the permeability of oil components, whereas the permeate flux obtained with the hydrophobic membrane (HF1-43-CM100) appears to be significantly low, indicating that synthetic cutting oil was easily wetted on the hydrophobic membrane surface and induced more membrane fouling. The effect of material characteristics of the membrane on the filtration characteristics was found to be much more significant compared with the mean pore size of the membrane. Backflushing by nitrogen gas was applied to reduce the formation of a gel layer and membrane fouling. With the hydrophilic membrane, the backflushing was found to increase the permeate flux, whereas the backflushing resulted in a decrease in flux for the hydrophobic membrane. The flux recovery was observed to be highest when the membranes fouled with waste synthetic cutting oil were immersed into a cleaning solution for more than 72 hours and then backflushed by nitrogen gas.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.208-208
• /
• 2004

공작기계와 절삭 공구의 발달로 고속 가공(high speed machining)의 도입이 가속화되고 있다. 고속 가공은 소재 제거율(MRR; material removal rate)을 향상시킴으로써 생산비용 및 생산 시간의 단축이 가능하며, 소경 공구를 이용한 고속 고회전 가공으로 고정밀 가공이 가능한 방법으로 생산 효율성 및 정밀성의 증대를 동시에 추구할 수 있는 가공 방법이다. 고속 가공에서 공구의 절입 및 퇴출 시에 급격한 절삭력의 변화로 인하여 공구의 파손(breakout) 및 칩핑(chipping)의 발생 가능성이 보다 높다.(중략)

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.12
• /
• pp.60-66
• /
• 2004

Increasing demands on precision machining of 3D free-form surface have necessitated the tool to move smoothly with varying feedrate. To this regard, parametric interpolators such as NURBS (Non-Uniform Rational B-Spline) interpolator have been introduced in CNC machining system. Such interpolators reduce the data burden in NC code, increase data transfer rate into NC controller, and finally give smooth motion while machining. In this research, a new concept to control cutting load in NURBS Interpolator was tried based on the curvature of curve. This is to protect cutting tool, and to have good machinability. For proof of the system, cutting force and surface topography were evaluated. From the experimental results. the interpolator is good enough for machining a free-form surface.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.1
• /
• pp.84-89
• /
• 2013

Titanium used in industry has been widely applied for aerospace engine, structures and spacecraft exterior, etc. because the titanium is higher in strength compared to the steel and light in weight compared to the steel. This study is to investigate the effect of cutting depth and cutting time on the spindle speed and feed rate of vertical machining center as a parameter to find the rough cutting time and cutting depth in the medium speed cutting machining of the titanium alloy. It is found that the cutting machining heat are increased as the cutting depth, feed rate, cutting time and spindle speed are raised.

• Explosives and Blasting
• /
• v.19 no.3
• /
• pp.105-113
• /
• 2001

채석, 굴착, 가공과 같은 워터젯 응용분야에서 대상재료에 깊은 홈(kerf)을 절단할 수 있는 실험실용 회전식 슬로터(slotter)를 제작하여 암석을 대상으로 워터젯 시스템의 절단효율을 시험하였다. 고압펌프는 유율 7.5 l/min, 압력 379 MPa, 용량 75 kW급의 JETPAC을 주로 사용하였고, 암석시료는 화강석인 제천석, 거창석을 사용하였다. 시험과정에서는 물과 연마재 투입에 의한 절단 및 진동식 슬로터에 의한 슬롯절단 기초시험을 먼저 수행하고, 그 결과를 토대로 회전식 슬로터에 의한 절단시험을 실시하였다. 순수한 물에 의한 시험의 결과 고압수류의 토출압력은 절단심도에 정비례하였고, 노즐의 이송속도는 이차함수 형태의 반비례 관계를 보였다. 연마재 투입시험에서는 순수한 물에 의한 경우에 비해 연마재로 인한 충격력의 증가로 절단심도가 크게 증가하였는데, 유사한 조건하에서 3~5배 이상의 절단심도의 증가를 보였다. 진동식 슬로터에 의한 슬롯절삭에서는 생성된 슬롯의 내벽면이 바닥으로 갈수록 좁아짐으로써 넓은 폭의 슬롯형성은 가능하나 절삭심도가 제한되었다. 회전식 슬로터에 의한 시험에서 생성된 슬롯들은 평균 22 mm의 폭으로 내벽면이 바닥까지 서로 평행하여 깊은 심도까지 비트진입이 가능하였다. 절단율은 16~32 mm/sec의 속도범위에서 $40~160{\;}\textrm{mm}^2/sec$로 나타났다. 한편, 최대유율 24 l/min의 HUSKY S-200 펌프에 의한 시험결과 JETPAC 펌프에 비해 1.13~3.47 배의 절단심도를 보였다

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.9
• /
• pp.4149-4155
• /
• 2013

High speed machining for higher cutting speed and feedrate lead to a increase of surface quality and material removal rate. This paper presents a study of the influence of cutting conditions on the vibration characteristics obtained by machining with face milling cutter for high speed machining. In this paper, Taguchi experimental design method which is based on orthogonal array table was applied to study vibration characteristics with high speed face milling cutter. The experimental conditions used orthogonal array of $L_{27}(3^{13})$. In this work, design and analysis of experiments is conducted to study the effects of these parameters on the vibration by using the S/N ratio, analysis of variance. Four cutting parameters namely, feed rate, champer length, cutting speed, and depth of cut were optimized with consideration of vibration characteristics.

• Tunnel and Underground Space
• /
• v.8 no.4
• /
• pp.332-341
• /
• 1998

Conventional polishing of stone panel edges has been done by hand. While this has changed somewhat with the advent of automatic machines, it is still very much a hand finishing technology. For the development of edge shape milling tool, the primary test on characteristics of edge shape milling tool was carried out. This paper presents the results of tests focused upon the milling capability that was varied by the variables of operation parameters. Author tried to confirm the effect of six operation parameters of equipment such as rotation speed, advance speed, applied load, water flow rate and rotational direction. The result from test was described in term of shape milling capability that was defined as cutting volume of rock by unit weight of tool wear. The variance of the results could indicate the optimum level of each operating parameters. The test was also carried out to determine the abrasion resistance varied according to the abrasive flow rate. The abrasion resistance was increased with the abrasive flow rate, but over some rate it was not changed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.7
• /
• pp.1654-1660
• /
• 2009

Two different cutting-oils from H and B companies which are sold as an eco-friendly cutting-oils were selected and the biodegradability of these commercially available cutting-oils was evaluated by the sequencing batch reactor (SBR) processes. The cutting-oil wastes ($H_1$) pre-treated by coagulation/flocculation was used as an influent to SBR. When the F/M ratio was operated 0.04 to 0.08kgCOD/kgMLSS d, removals of $BOD_5$and $COD_{Cr}$were above 97% and 91%, respectively. T-N and T-P removals were above 76% and 81%, respectively. If the diluted cutting-oil wastes ($B_1$) was used as an influent of the SBR, $COD_{Cr}$removals were above 77% at the F/M ratio of 0.01-0.02kgCOD/kgMLSS d. After the cutting-oil wastes was treated by coagulation/ flocculation ($B_2$), $COD_{Cr}$removals was above 85%. If the pre-treated cutting-oil wastes were mixed with a synthetic wastewater ($B_3$) and fed into the SBR in order to mimic the real wastewater treatment plant situation, $BOD_5$and $COD_{Cr}$removals were above 97%, 91%, respectively. T-N and T-P removals were above 79% and 76%. The ratio between $BOD_5$and $COD_{Cr}$, ($COD_{Cr}$-$BOD_5$)/$COD_{Cr}$, indicating the biodegradability of effluent of the SBR, was calculated to 85% and 61%. This means that significant amounts of non-readily-biodegradable organic compounds in the effluent of $H_1$, $B_3$are still present.

• Membrane Journal
• /
• v.6 no.4
• /
• pp.219-226
• /
• 1996

Rotary disc ultrafiltration module(RDM) was developed for the separation of oil emulsions. This module was devised to reduce the gel polarization phenomenon by alecoupling the operation pressure and the surface velocity of solution in ultrafiltration(UF) processes. Two-shaft engaged disc type RDM having 20 rotary disc membcanes(UOP, USA) was operated under 85kPa vacuum at $25^{\circ}$C. The pressure drop due to slip flow in the two-shaft RDM was found to be proportional to $(2.5{\omega}r)^{2}$. The pure water flux of two-shaft RDM decreased by 9.95% at the angular velocity of 41.89rad/s compared to the decrease of 3.01% for one-shaft RDM at the same velocity. When the angular velocity was changed from 31.42rad/s to 2.62rad/s, the flux decline for 1% cutting oil in two-shaft RDM was 30.16% that is similar to that of one-shaft RDM. Disc gap of 3mm and 7mm did not show any significant differences in the flux for 1% cutting oil solution. A modified model for two-shaft RDM showed good agreement with the experimental results for the cutting oil solution.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.1
• /
• pp.131-137
• /
• 1986

Cutting oil cools the chip and a tool as well as lubricates the chip-tool interface, the flank and machined surface. Rehbinder effect has been known as a phenomenon, the reduction of mechanical strength, when the metal is exposed to a polar organic environment or the surface of metal is coated with some polar organic substances. About the cause of Rehbinder effect there have been many different ideas by Rehbinder, Shaw, Barlow, Sakida and etc. In this report, the efect of polar organic substance( $C_{6}$ $H_{5}$C $H_{3}$+ $C_{6}$ $H_{4}$(C $H_{3}$)$_{2}$+ $C_{4}$ $H_{9}$OH+ $C_{6}$ $H_{12}$ $O_{2}$) (magic ink) upon the mechanism of chip formation on the orthogonal cutting of copper and mechanical properties of the work material are experimentally discussed with various rake angles. As expected no lubrication action could be noticed, but the shear angle increased and the cutting force and shear strain on the shear plane decreased, therefore the work material must be embrittled under polar organic substance.substance.