• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2000.11a
• /
• pp.89-92
• /
• 2000

수간가공업의 소규모 영세화에 따른 비효율적인 산업구조를 개선시키며 낙후된 시설의 현대화, 3D업종의 인력대체 효과, 어류가공업체의 생산성, 수익률 증대를 목적으로 다양한 어종의 크기에 가변적인 자동절단시스템이 필요로 하게 된다. 다양한 어종에 대한 크기, 너비에 대한 데이터를 신경망의 파라메타로 하여 최소한의 센서로 최적의 절단부분을 예측, 가변적인 어류의 크기에 따라 최적의 절단부분을 출력으로 갖는 효율적인 절단공정을 지닌 시스템을 IBM-PC 인터페이스 기반으로 구축하며 PC의 모니터링을 부가시켜 제어함으로써 신경회로망의 우수성을 입증했다.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.11a
• /
• pp.87-95
• /
• 2005

Laser sealing/cutting technique, one of the 4 core technologies to manufacture self-luminous glass tubes (SLGTs) has been developed. Through the analysis of commercial products it is found that Pyrex Is used for SLGTs. A CO2 laser, which is commonly used for glass work was used for the study The factors affecting the sealing/cutting were laser intensity, duration. Irradiation method, and pressure inside the tube. The whole Process is composed of 2 stages. In the first stage. both ends of the tubes are sealed while tritium is insected in the tubes. And the tritium sealed tubes are cut in the desired size in the second stage. Defocused beam was used for seal ing and focused beam was used for cutting. After the sealing/cutting, the tubes were heat treated to prevent fracture due to the residual heat stress.

• Food Science and Preservation
• /
• v.22 no.1
• /
• pp.154-157
• /
• 2015

To maintain the freshness and to prevent browning of cut Kimchi cabbages, the effect of the cutting process using a ceramic knife under $N_2$ blowing on the quality of the cut Kimchi cabbages was investigated. Kimchi cabbages cut with a ceramic knife under $N_2$ gas blowing conditions (NC) were stored at $5^{\circ}C$ for 7 days, and their weight reduction ratio and the browning degree and appearance were compared with those of the control treatment samples (OS; cut with a stainless steel knife under normal air, OC; cut with a ceramic knife under normal air). The weight reduction ratios were 0.07~0.13%, and the NC treatment showed the lowest reduction ratio among all the treatments (p<0.05). The Hunter L values increased, but the a and b values decreased after 5-day storage in all the treatments. The NC treatment had higher L values but lower a and b values than the OS and OC treatments. The browning degrees by Hunter color value, PPO activity, and appearances were the least in the NC treatment (p<0.05). The cutting process with a ceramic knife under $N_2$ blowing could be applied to the cutting of vegetable products and for minimal fruit processing.

• KSBB Journal
• /
• v.18 no.4
• /
• pp.306-311
• /
• 2003

Solid-phase refolding of immobilized proteins can be an effective way to reuse an immobilized enzyme column. Oriented immobilization methods are known to provide higher activity of the immobilized enzymes. In this study, using recombinant EK (enterokinase) as a model enzyme and a fusion protein, that consisted of recombinant human growth hormone and six His tag that was linked by the peptide of EK-specific recognition sequence, as a model substrate, we evaluated two oriented immobilization methods, i. e., reductive alkylation of N-terminus ${\alpha}$-amine and affinity interaction between poly-histidine tag and Ni-NTA (nickel-nitrilotriacetic acid). The immobilization yield, activity and cleavage of the immobilized enzymes, and the yield of solid-phase refolding were compared. The Ni affinity immobilization and the covalent immobilization yields were about 100％ and 65％, respectively. But the specific activities were the same, about 50％ of that of the soluble enzyme. The cleavage rate by the covalently immobilized EK was higher than the soluble enzyme and the side reaction of cryptic cleavage was significantly decreased. Covalently immobilized EK showed almost 100％ refolding yield but the affinity immobilized EK showed only 70％ yield, which suggested the covalent conjugation provided more rigid ‘reference structure’ for the solid-phase refolding. The monomeric hGH could be easily obtained by capturing the cleaved poly Histidine tag by the Ni affinity column.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.1
• /
• pp.91-101
• /
• 2017

In this study, we conducted the preliminary research for high speed laser cutting of LED module. In particular, the feasibility of ultra-high speed laser cutting of 100 mm/s which exceeds the cutting speed of conventional dicing saw was examined. For this, copper/ceramic and silicone/ceramic hybrid substrates, which are the components of the LED module, were fabricated, and the surface morphology, surface roughness and flexural strength of the laser-cut samples were investigate and compared with the dicing-cut samples. To investigate optimal laser cutting conditions for hybrid substrates, the effects of various laser cutting conditions on cutting surface characteristics were studied using single ceramic and copper substrate. Optimal laser cutting conditions of the hybrid substrates were the use of Ar assist gas, high laser power and high assist gas pressure. Comparing the cutting surface of the hybrid substrates, the surface characteristics of the laser-cut samples are slightly inferior to those of the dicing-cut samples. The average surface roughness of the laser-cut samples was about $9{\mu}m$, and that of the dicing-cut samples was about $4{\mu}m$. However, considering very low cutting speed (3 mm/s) of the dicing saw, the surface morphology of the laser-cut sample was relatively uniform, and the surface roughness was not much different from that of the dicing-cut sample. The flexural strength of the laser-cut samples was equivalent to or slightly inferior to the flexural strength of dicing-cut samples. However, if the laser processing conditions are sufficiently optimized, the ultra-high speed laser cutting of the LED module will be possible.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2003.05a
• /
• pp.19-22
• /
• 2003

경사의 사선방향으로 절단하여 봉제된 바이어 컷 직물로 제조된 의류는 일반 의류와 달리 우아한 외관을 타나낸다. 이 직물의 단점은 형태안정성이 나빠서 완전제품의 형태가 패턴의 형의 형태와 다른 모양을 나타내는 경우가 많으며, 특히 밑단 부분이 불균일하게 쳐지므로, 가지런히 절단하는 트리밍공정을 부가적으로 거치게 된다. 현재의 봉제 공정에서는 트리밍 단계를 모두 숙련공들의 수작업에 의존한 평면 커팅 방법으로 수행하기 때문에 작업자의 피로도에 따라 불량품이 양산되고 그에 따른 소비자들의 불만 요인도 높아지므로, 본 연구에서는 치수 조절 마네킹을 제조하여 실제 의복 착용 상태를 그대로 재현 한 후, 회전시키면서 스스로 회전하는 자동 커터에 의해서 공간상에서 트리밍 하는 3-D 입체 시스템을 개발하였다. 이 시스템에 의하여 제조된 의류는 트리밍 라인이 균일하고 매끄러우며, 안감이 밖으로 밀려나오는 경우가 없어 외관상 품위가 있는 외관을 나타내었다. 또한 수작업에 비하여 제조 속도가 훨씬 빠르므로 봉제 후공정에서의 의류 제조 시간을 획기적으로 단축하는 신속 생산 시스템의 요소로서 충분히 사용될 수 있는 가능성을 나타낸다.

• KIPS Transactions on Computer and Communication Systems
• /
• v.8 no.12
• /
• pp.297-304
• /
• 2019

The technological advances such as communication, sensor, and artificial intelligence lead smart factory construction. Smart factory aims at efficient process control by utilizing data from the existing automation process and intelligence technology such as machine learning. As a result of constructing smart factory, productivity increases, but costs increase. Therefore, small companies try to make a step-by-step transition from existing process to smart factory. In this paper, we have proposed a remote control system that support data collection, monitoring, and control for manufacturing equipment to support the construction of CNC cutting machine based small-scale smart factory. We have proposed the structure and design of the proposed system and efficient sensing data transmission scheme. To check the feasibility, the system was implemented for CNC cutting machine and functionality verification was performed. For performance evaluation, the web page access time was measured. The results means that the implemented system is available level.

• Journal of the Korean Institute of Gas
• /
• v.2 no.1
• /
• pp.74-82
• /
• 1998

The grain boundary etching method as a technique for assessing degradation of structural materials used at elevated temperature has received much attention since it is simple, inexpensive and easy to apply to real plant components. In this study, the technique is applied to some aged petroleum and chemical plant components such as reactors and drums. As a degradation parameter, intersection number ratio ($N_i/N_o$), is employed. The intersection number ratio ($N_i/N_o$) is defined as the ratio of intersection number ($N_i$) obtained from 5-minute picric acid etched surface to the number ($N_o$) obtained from Nital etched surface. In order to study degradation level, several relationships were measured such as the correlation between shift in ductile brittle transition temperature, $({\Delta}DBTT)_{sp}$ and intersection number ratio, ($N_i/N_o$) and the correlation between the measured ($N_i/N_o$) values and Larson-Miller Parameter values.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.393-396
• /
• 2000

Spent fuel rod cutting device should cut a spent fuel rod to an optimal size in order to fast decladding operation. In this paper, for developing spent fuel rod cutting device with cutter blade, rod properties such as dimension and material of zircaloy tube and fuel pellet are investigated at first and then, various methods of existing cutting devices used commercially are investigated and their performance are analyzed and compared. This device is designed to be operated automatically via remote control system considering later use in Hot-Cell (radioactive area) and the mdularization in the structure of this device makes maintenance easy. SUS and Zircaloy-4 are selected as cut material used in the test of spent fuel rod cutting device by cutter blade. In order for constructing the high durable cutter blade, various materials are analyzed in terms of quality, shape, characteristic, and heat treatment, etc. and from these results, spent fuel rod cutting device is designed and manufactured based on the considerations of durability, round shape sustainability of rod cross-section, debris generation, and fire risk, etc.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1996.04a
• /
• pp.280-280
• /
• 1996