Kim, Dong-Hun;Doh, Chil-Hoon;Lee, Jeong-Hoon;Lee, Duck-Jun;Ha, Kyeong-Hwa;Jin, Bong-Soo;Kim, Hyun-Soo;Moon, Seong-In;Hwang, Young-Ki
Journal of the Korean Electrochemical Society
/
v.11
no.4
/
pp.284-288
/
2008
Sn-thin film as high capacitive anode for thin film lithium-ion battery was prepared by organic-electrolyte electroplating using Sn(II) acetate. Electrolytic solution including $Li^+$ and $Sn^{2+}$ had 3 reduction peaks at cyclic voltammogram. Current peak at $2.0{\sim}2.5\;V$ region correspond to the electroplating of Sn on Ni substrate. This potential value is lower than 2.91 V vs. $Li^+/Li^{\circ}$, of the standard reduction potential of $Sn^{2+}$ under aqueous media. It is the result of high overpotential caused by high resistive organic electrolytic solution and low $Sn^{2+}$ concentration. Physical and electrochemical properties were evaluated using by XRD, FE-SEM, cyclic voltammogram and galvanostatic charge-discharge test. Crystallinity of electroplated Sn-anode on a Ni substrate could be increased through heat treatment at $150^{\circ}C$ for 2 h. Cyclic voltammogram shows reversible electrochemical reaction of reduction(alloying) and oxidation(de-alloying) at 0.25 V and 0.75 V, respectively. Thickness of Sn-thin film, which was calculated based on electrochemical capacity, was $7.35{\mu}m$. And reversible capacity of this cell was $400{\mu}Ah/cm^2$.
Gallium is an important material and is used by industry of oxide semi-conductor and LED chip. However, the most of the gallium-containing waste resources became outflow abroad and the most of which is imported from oversea by following technical problem and low circulation rate. In this research, the recovery of high purity Gallium metal from Gallium scrap, which containing about 30% of Gallium, was investigated by using hydro-metallurgical process. As pretreatment, the Gallium scrap was pulverized and leached by strong acid such as hydro chloric acid. At the leached solution, Indium was separated as an Indium sponge by substitution reaction and then Gallium and Zinc hydroxide separated and filtrated using strong alkaline solution such as sodium hydroxide by precipitation method. Also, Gallium metal and Zinc metal was recovered by electrowinning method. To make an electrolytic solution, Gallium and Zinc hydroxide was leached by strong alkaline solution. Finally, High purity Gallium metal was recovered by vacuum refining process to remove the Zinc impurity.
Sohyeong Oh;Dong Geun Yoo;Myoung Hwan Kim;Ji Young Park;Kwonpil Park
Korean Chemical Engineering Research
/
v.61
no.2
/
pp.189-195
/
2023
As a PEMFC (Polymer Exchange Membrane Fuel Cell) cathode catalyst, Pt-Co/C has recently been widely used because of its improved durability. In a fuel cell, electrodes and electrolytes have a close influence on each other in terms of performance and durability. The effect on the electrochemical durability of the electrolyte membrane when Pt-Co/C was replaced in the Pt/C electrode catalyst was studied. The durability of Pt-Co/C MEA (Membrane Electrode Assembly) was higher than that of Pt/C MEA in the electrochemical accelerated degradation process of PEMFC membrane. As a result of analyzing the FER (Fluorine Emission Rate) and hydrogen permeability, it was shown that the degradation rate of the membrane of Pt-Co/C MEA was lower than that of Pt/C MEA. In the OCV (Open Circuit Voltage) holding process, the rate of decrease of the active area of the Pt-Co/C electrode was lower than that of the Pt/C electrode, and the amount of Pt deposited on the membrane was smaller in Pt-Co/C MEA than in Pt/C MEA. Pt inside the polymer membrane deteriorates the membrane by generating radicals, so the degradation rate of the membrane of Pt/C MEA with a high Pt deposition rate was higher than Pt-Co/C MEA. When the Pt-Co/C catalyst was used, the electrode durability was improved, and the amount of Pt deposited on the membrane was also reduced, thereby improving the electrochemical durability of the membrane.
Kim, Seong-En;Lee, Sang-Lin;Kang, Sin-Choon;Kim, I-Cheol;Sheikh, Rizwan;Park, Yeung-Ho
Clean Technology
/
v.18
no.2
/
pp.183-190
/
2012
Electrochemical regeneration of the iron chloride waste solution from PCB etching reduces environmental contamination and produces copper as by-product, so the economic feasibility is high. But iron chloride waste solution contains iron and copper and the reactions occurring in the electrolytic cell are complicated. In this work, the oxidation of iron chloride and copper deposition were examined through batch electrolysis and the optimum conditions of the process parameters were found. The oxidation of ferrous chloride was achieved easily to the desired level. The copper deposition efficiency was high in the reaction using the carbon cathode when the copper density was 12 g/L with the electric current density of $350mA/cm^2$, and the ratio of the $Fe^{2+}$ ion was high. In addition, the possibility of the scale-up was confirmed in continuous operation of bench reactor using the optimum conditions obtained.
Efficient removal of nickel from the ferric chloride etching solution has been studied. At first, $Fe^{3+}$ was reduced to $Fe^{2+}$ by the electrolytic iron flake or the waste shadow mask iron plate. And then, $Ni^{2+}$ was removed from the solution by electrolytic iron powder. Under the optimum conditions the reduced rates of nickel were 99 % and 98%, respectively at the initial $Ni^{2+}$ concentrations of 1.0% and 0.1%. Sludge formed during reduction of $Fe^{3+}$ in the solution were analyzed by XRD and SEM.
An investigation on the recovery of nickel from spent electroless plating solutions has been performed using the electrowinning method. For this aim, nickel in spent electroless plating solutions was separated as nickel hydroxide through the addition of caustic soda. Nickel hydroxide was completely dissolved with sulfuric acid and an electrolysis was performed for electrowinning of nickel from nickel solutions. As a result, it was found that more than 99% of nickel in spent electroless plating solutions could be precipitated as nickel hydroxide above pH 10 with the addition of caustic soda. As far as the current efficiency in electrowinning of nickel was concerned, it was decreased with increase in the current density.
Kim, Jeonghyun;Song, Minkyeong;Kim, Jinwoo;Yu, Yeontae
한국신재생에너지학회:학술대회논문집
/
2011.11a
/
pp.86.2-86.2
/
2011
저온형 연료전지인 직접 메탄올 연료전지(Direct Methanol Fuel Cells, DMFC)는 친환경적인 발전 시스템, 높은 에너지 효율의 장점 때문에 주목을 받고 있으나 연료극의 촉매로 사용되는 금속은 고가의 귀금속인 Pt와 Ru가 요구되어 제조비용이 비싸기 때문에 촉매의 양을 줄이고, 반응 도중 생성되는 CO에 의한 촉매의 피독 문제 등 해결하여야 할 점이 산적해 있어 연료전지 중 촉매의 활성을 높이는 연구들이 활발히 이루어지고 있다. 종래의 MEA의 촉매층 제조공정은 우선 환원석출법에 의해 Pt-Ru/C를 합성하고 Nafion 용액에 혼합하여 Pt-Ru/C 슬러리를 제조한다. 이 방법에서는 carbon sheet에 spray 방법으로 Pt-Ru/C 촉매층이 만들어지기 때문에, Pt-Ru 촉매가 Nafion에 의해 부분적으로 매몰되어 촉매의 전기화학적 활성이 떨어지는 문제점이 있다. 이를 해결하는 방안으로 펄스전류를 이용하여 Pt-Ru 합금입자를 carbon sheet에 전기화학적으로 담지 시켜 Nafion에 매몰되는 것을 방지하는 펄스전해법 연구가 진행되고 있다. 그러나 촉매의 입자크기가 일반적으로 50~70 nm 이상으 크기 때문에 촉매의 낮은 활성이 문제점으로 야기되고 있다. 본 연구에서는 Pt-Ru/C 촉매층 제조 문제점을 해결하고, 촉매의 전기화학적 활성을 증가시키기 위해서 2~4 nm Pt-Ru 콜로이드를 전해액으로 사용하고, 전기영동법을 이용하여 Pt-Ru 나노 입자를 carbon sheet($1{\times}1cm^2$) 에 담지 시켰다. 전기영동법에서 균일한 Pt-Ru 촉매층의 제조를 위해 전류인가 방법으로는 펄스전류를 사용하였고, 실험변수로는 전해액 pH, duty cycle, 담지시간을 선정하였다. 합성된 Pt-Ru 콜로이드를 TEM분석으로 나노입자의 크기와 분산성 분석하였고, 콜로이드 나노입자의 표면전하 상태를 분석하기 위해 zeta-potential을 분석하였다. Pt-Ru/C의 촉매의 전기화학적 활성을 분석하기 위하여 0.5 M H_2SO_4$ 와 1 M $CH_3OH$ 혼합용액에 CV(Cyclic Voltammetry)실시하였고, carbon sheet 전극 상 Pt-Ru의 분산성 확인을 위하여 FE-SEM분석을 수행하였다.
Journal of the Korean Graphic Arts Communication Society
/
v.8
no.1
/
pp.53-70
/
1990
It is well known that viologens such as 1.1 - disubstituted 4, 4` - bipyridinium salts and those used as redox indicator, herbicide and electrocheromic display device because those possess the lowest redox potential in any organic system. Viologen salts produced reversible high blue color under the influence of radical cation by photoreduction This study is related to the synthesis of viologen derivatives and the photoreduction property in water solution stats and the polar aprotic polyvinylpyrrolidone(PVP) matrix.
Proceedings of the Korea Society for Energy Engineering kosee Conference
/
1994.05a
/
pp.114-117
/
1994
아연-산화은 전지는 높은 에너지 및 전력밀도를 가지고 있으나 비싼 제작비용 때문에 우주항공, 군사무기 등 특수한 분야에서 주로 이용되며, 특히 전해액이 별도의 용기에 보관되어 있다가 외부 신호에 의해 충전된 dry상태의 전지에 주입되어 활성화되는 1차 또는 비축형 아연산화은 전지는 우수한 고율방전 특성, 장시간의 저장기간 및 활성화와 동시에 부하를 인가 할 수 있는 특성 때문에 많은 무기체계에서 이용하고 있다. 이러한 아연-산화은 전지의 아연전극은 높은 다공도와 반응 면적을 가져야 하며, 특히 방전중 아연전극의 전위는 가역 수소전위 보다 더 음전위이기 때문에 수소가스가 다량 발생하게 되므로 수은과 같은 높은 과전압을 갖는 물질을 첨가하여 가스 발생량을 줄이고 부동태화(passivation)를 억제하게 된다. 그러나 국내 여건상 수은을 사용하여 전지를 제작하는 것은 환경문제 등으로 인하여 어렵기 때문에 본 연구에서는 수은을 사용하지 않고 비축형 아연-산화은 전지의 음극판을 제작하기 위하여 전착법(electro deposit)과 mesh 제작방법을 혼합하여 아연전극을 제작하였으며, 기판에 석출된 아연과 아연 mesh의 질량비율에 따른 전지의 성능을 평가하였다.
Proceedings of the Korean Institute of Surface Engineering Conference
/
2015.05a
/
pp.133-133
/
2015
최근 인쇄회로기판의 실장용 표면처리 개발에서 전도성이 우수하며, 또한 실장성도 우수한 치환형 무전해 은도금의 개발이 진행되고 있다. KENNY 등은 인쇄회로기판에서 가장 우수한 실장용 표면처리의 치환형무전해 은도금기술을 발견하였다. 이 기술은 무전해 니켈도금/치환금도금과 비교하여 비교적 낮은 비용으로 양산이 가능하며, 우수한 솔더링 특성과 신뢰성이 높은 것이 특징이다. 개발한 치환형 무전해 은도금은 무전해 니켈도금/치환금도금에 비해서 저온에서 처리가 가능하며, 처리시간도 짧은 것이 특징이다. 특히 대량생산과 미세한 블라인드 비어홀(BVH, Blind Via Hole) 내부로의 균일 석출을 위한 수평컨베이어나 수직침적라인 등에 모두 적용이 가능하다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.