• Korean Chemical Engineering Research
• /
• v.54 no.6
• /
• pp.746-752
• /
• 2016

In this study, soft carbon was prepared by carbonization of carbon precursor (pitch) obtained from PFO (pyrolysis fuel oil) heat treatment. Three carbon precursors prepared by the thermal reaction were 3903 (at $390^{\circ}C$ for 3 h), 4001 (at $400^{\circ}C$ for 1 h) and 4002 (at $400^{\circ}C$ for 2 h). After the prepared soft carbon was ground to a particle size of $25{\sim}35^{\circ}C$, the soft carbon was synthesised by the chemical treatment with boric acid ($H_3BO_3$). The prepared soft carbon were analysed by XRD, FE-SEM and XPS. Also, the electrochemical performances of soft carbon were investigated by constant current charge/discharge test, cyclic voltammetry and impedance tests in the electrolyte of $LiPF_6$ dissolved inorganic solvents (EC:DMC=1:1 vol%+VC 3 wt%). The coin cell using soft carbon of $25{\sim}35^{\circ}C$ with 3903 soft carbon ($H_3BO_3$/Pitch=3:100 in weight) has better initial capacity and efficiency (330 mAh/g, 82%) than those of other coin cells. Also, it was found that the retention rate capability of 2C/0.1C was 90% after 30 cycles.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.9
• /
• pp.931-935
• /
• 2012

In this study, we fabricate and investigate low-temperature solid oxide fuel cells with a ceramic substrate/porous metal/ceramic/porous metal structure. To realize low-temperature operation in solid oxide fuel cells, the membrane should be fabricated to have a thickness of the order of a few hundreds nanometers to minimize IR loss. Yttrium-doped barium zirconate (BYZ), a proton conductor, was used as the electrolyte. We deposited a 350-nm-thick Pt (anode) layer on a porous substrate by sputter deposition. We also deposited a 1-${\mu}m$-thick BYZ layer on the Pt anode using pulsed laser deposition (PLD). Finally, we deposited a 200-nm-thick Pt (cathode) layer on the BYZ electrolyte by sputter deposition. The open circuit voltage (OCV) is 0.806 V, and the maximum power density is 11.9 mW/$cm^2$ at $350^{\circ}C$. Even though a fully dense electrolyte is deposited via PLD, a cross-sectional transmission electron microscopy (TEM) image reveals many voids and defects.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.2
• /
• pp.161-170
• /
• 2012

There are many factors to consider when attempting to improve the efficiency of fuel cell operation, such as the operation temperature, humidity, stoichiometry, operation pressure, geometric features, etc. In this paper, the effects of the operation pressure were investigated to find the current density and water saturation behavior on a cross section designated by the design geometry. A two-dimensional geometric model was established with a gas channel that can provide $H_2$ to the anode and $O_2$ and water vapor to the cathode gas diffusion layer (GDL). The results from this numerical modeling revealed that higher operation pressures would produce a higher current density than lower ones, and the water saturation behavior was different at operation pressures of 2 atm and 3 atm in the cathode GDL. In particular, the water saturation ratios are higher directly below the collector than in other areas. In addition, this paper presents the dependence of the velocity behavior in the cathode on pressure changes, and the velocity fluctuations through the GDL are higher in the output area than in inlet area. This conclusion will be utilized to design more efficient fuel cell modeling of real fuel cell operation.

• Journal of the Korean Society of Radiology
• /
• v.6 no.4
• /
• pp.267-273
• /
• 2012

Abnormal gastric emptying time of dog by alien substance, neoplasm, pyloric antrum hyperplasia, stomach surgery, electrolyte imbalance, stomach-dilated torsion is clinically important as a digestive disease. Therefore study aims to provide basic data on the clinical usefulness of gastric emptying time test which uses radiopaque Kolomark developed in Korea rather than using the existing BIPS for the dog. 9 beagles were used for this experiment and their average weight was about 10.3kg with 2.5 year-old average age. For the test, fast for 12 hours was made without chemical sedation, and just before the test, 1 capsule of Kolomark was fed with 25% of daily feed amount, and we took photographs at ventrodorsal and right lateral position after 2, 4, 8 and 12 hours. As for interested reading area, we observed entire stomach from cardia to stomach pyloric part, and as for analysis method, we counted Kolomarks remained in the stomach per time and judged only P value below 0.05 to be meaningful by using Friedman Test. After feeding Kolomark through oral cavity, it took average 7.55 hours for the Kolomark to have escaped from the stomach to small intestine. In this study of gastrointestinal tract passing time after feeding matured dog, we used Kolomark and expect that it could be a basic data for normal gastrokinetic time.

• The Korean Journal of Ecology
• /
• v.22 no.5
• /
• pp.277-285
• /
• 1999

To develop a better restoration technique for altering urban planted forest to more natural forest, the changes of flora, vegetation structure and woody plant growth in the early stage after lumbering only Populus albaglandulosa of the tree layer were studied in Chungdam Park, Chungdam-dong, Kangnam-gu, Seoul for two years (from 1997 to 1998). The results were as follow. First, in the year after lumbering, the species changes occurred not in woody plants but in herbs, which increased by 44%. Three species including Viola verecunda disappeared, and 15 species including ruderals such as Metaplexis japonica and introduced species such as Erechtites hieracifolia appeared newly. Second, lumbering caused the coverages of Quercus aliena, Q. mongolica, Q. acutissima and Sorbus alnifolia in the subtree, or shrub layer, to be increased abruptly. The coverage of Lespedeza bicolor was affected by neighboring plants. Third, in the herb layer the coverage of Artemisia keiskeana was conspicuously increased but those of the others were not. Fourth, by ridding the upper layer canopy, Quercus' growth rates were increased highly. Rates of DBH growth of Q. aliena, Q. mongolica and Q. dentata were increased to 53.0%, 22.9% and 8% in the experimental area, and 23.1%, 8.3% and 6.1% in the control area, respectively, during two growing seasons (from May 11, 1997 to October 27, 1998). The ratios of twig biomasses of the previous year to the next year were 100:565 in Q. aliena, 100:197 in Q. mongolica and 100:644 in Q. dentata in the experimental area. There were also growth ratios of 100:117 in Q. aliena, 100:100 in Q. mongolica and 100:42 in Q. dentata in the control area, respectively. The growth rate increases of Q. aliena and Q. dentata were thus conspicuous in twig rather than in trunk, but that of Q. mongolica was vice versa.

• Journal of Navigation and Port Research
• /
• v.33 no.10
• /
• pp.703-707
• /
• 2009

In order to evaluate applicability of cylindrical slit type block breakwater to the field water, which was designed from the previous physical model study, it is analyzed the calmness of harbor area by the numerical model experiment. For a small fishery port in southern coast of Korea a SWAN model using the wave action balance equation was formulated. The reflection and transmission coefficients induced by the physical model test were introduced to the numerical model. The model response with cylindrical slit type breakwater was compared with the impermeable breakwater case and the possibility of water quality improvement through the water circulation by the new structure was investigated. For numerical simulation, parameters of deepwater design wave from the prediction report II for overall deepwater design wave by KORDI were used and wind parameters from the 50years return period observed for 37years(1970~2006) were adopted in the numerical model. The response of west breakwater in Mijo port applying the NE and NNE waves, which were dominant in this area, was analyzed. It was found that the transmission characteristic of designed cylindrical slit breakwater was well presented in the numerical model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.1
• /
• pp.78-82
• /
• 2005

Display manufacturing process has adopted RCA cleaning, applying to larger area and coping with environmental issue for last ten years. However, the approaching concept of ozonized, hydrogenised, or electrolyzed water cleaning technologies is within RCA clean paradigm. In this work, only electrolyzed anode water was applied to clean particles and organics as well as metals based on Pourbaix concept, and as a test vehicle, MgO particles were introduced to prove the new concept. The electrolyzed anode water is very oxidative with high oxidation reduction potential (ORP) and low in pH of more than 900 mV and 3.1, respectively. MgO particles were immersed in the anode water and its weight losses due to dissolution were measured with time. Weight losses were in the ranges of 100 to 500 micrograms in 250 ml anode water depending on their ORP and pH. Therefore it was concluded that the cleaning radicals in the anode water was at least in the range of 1 to $5{\times}10^{20}$ ea per 250 ml anode water equivalent to $1{\times}10^{18} ea/cm^2$. Hence it can be assumed that the anode water applied to display cleaning from now on $1{\times}10^{10}$ to $1{\times}10^{15} ea/cm^2$ ranges of contaminants are being treated. In addition, it was observed that anode water did not develop micro-roughness on hydrophobic surface while it did on the native silicon oxide.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.4
• /
• pp.229-235
• /
• 2003

A precursor of lithium manganese oxide was synthesized by mixing $(CH_3)_2CHOLi\;with\;Mn(CH_3COO)_2{\cdot}4H_2O$ in ethanol using a sol-gel method, then heat-treated at $400^{\circ}C\;and\;800^{\circ}C$ in air atmosphere. The condition of heat treatment was determined by thermogravimetric analysis/differential thermogravimetric analysis (TGA/DTA). The characterization of the lithium manganese oxide was done by X-ray diffraction (XRD) spectra and scanning electron microscopy (SEM). The electrochemical characteristics of lithium manganese oxide electrode for lithium ion battery were measured by cyclic voltammetry (CV), chronoamperometry and AC impedance method using constant charge/discharge process. The electrochemical behaviors of the electrode have been investigated in a 1.0M $LiClO_4/propylene$ carbonate electrolyte solution. The diffusivity of lithium ions, $D^+\;_{Li}\;^+$, as determined by AC impedance technique was $6.2\times10^{-10}cm^2s^{-1}$.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.75-75
• /
• 2009

연성회로기판은 일반적으로 절연체를 이루는 폴리이미드와 전도체를 이루는 구리로 구성되어 있다. 폴리이미드는 뛰어난 열적 화학적 안정성, 기계적 특성, 공정성 등의 장점으로 인해 연성회로기판의 절연체로서 제안되었지만 전도체를 이루는 구리와의 접합 특성이 우수하지 않기 때문에 많은 연구가 현재까지 진행되고 있고, 그 결과 연성회로기판의 접합 특성에 많은 개선이 이루어짐과 동시에 다양한 공정 방법이 제안되고 있다. 하지만 고온다습한 환경에서 사용될 경우 폴리이미드의 높은 흡습성과, 구리와 seed layer의 산화 문제로 인해 접합 특성이 저하된다는 단점 또한 가지고 있다. 따라서 본 연구를 통해 고온다습한 조건하에서 seed layer가 80Ni/20Cr 합금으로 구성된 연성회로기판의 seed layer의 두께와 시효시간으로 인해 발생하는 접합 신뢰성의 차이를 관찰하였다. 본 연구에서는 두께 $25{\mu}m$의 폴리이미드 위에 각각 100, 200, $300{\AA}$ 두께의 80Ni/20Cr의 합금 조성을 가지는 seed layer를 스퍼터링 공정을 통해 형성한 후 전해도금법을 이용하여 $8{\mu}m$ 두께의 구리 전도층을 형성하였다. 접합 특성 평가를 위해 ICP 규격에 따라 전도층 패턴을 폭 3.2mm, 길이 230mm로 시편을 제작하여 50.8mm/min의 이송 속도로 각 시편당 8회의 $90^{\circ}$ peel test를 실시하였다. 또한 $85^{\circ}C$/85% 항온항습 조건하에서 각각 24, 72, 120, 168시간 동안 시효 처리 후 같은 방법으로 연성회로기판의 접합 특성을 평가하였다. 파면의 형상과 조성을 분석하기 위해 SEM (Scanning electron microscope)과 EDS (Energy-dispersive X-ray spectroscopy)를 사용하였으며, 파면의 조도 측정을 위해 AFM (Atomic force microscope)을 사용하였다. 또한 파면의 잔여물 분석을 위해 EPMA (Energy probe microanalysis)를 사용하였고 계면의 화학적 결합상태를 분석하기 위해 XPS (X-ray photoelectron spectroscopy)를 통해 파면을 분석하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.50.2-50.2
• /
• 2011

염료감응형 태양전지는 기존의 실리콘 태양전지에 비해 저렴한 가격과 다양한 날씨 조건에서도 태양광과의 반응성이 안정하다는 여러 가지 장점을 갖고 있다. 하지만 광전 변환 효율이 기존의 실리콘 태양전지에 비해 현저히 떨어진다는 문제점과 장기적으로 안정하지 못하다는 단점을 가지고 있다. 이러한, 염료감응형 태양전지에서 크게 광전 변환 효율을 향상시킬 수 있는 재료는 염료, $TiO_2$와 같은 반도체 산화물전극 재료, 전해질이다. 이 중 $TiO_2$의 특성 및 크기는 염료감응형 태양전지의 효율에 영향을 미친다. 염료감응형 태양전지의 광전 변환 효율을 증가시키기 위해서 $TiO_2$는 넓은 비표면적, 높은 전자의 이동성 및 태양광과의 우수한 반응성을 가져야 한다. Microwave hydrothermal 방법에 의해 제조된 hollow $TiO_2$를 염료감응형 태양전지에 적용시킬 경우 기존의 $TiO_2$의 광흡수 반응이 200~400 nm 사이에서 발생하는 반면, hollow $TiO_2$의 광흡수 반응은 기존의 UV 영역인 200~400 nm 뿐만 아니라 가시광 영역인 400~460 nm 에서도 광흡수 반응이 가능하기 때문에 염료감응형 태양전지에서 광전 변환효율을 증가 시킬 수 있을 것으로 기대된다. 또한, microwave hydrothermal법에 의해 제조된 hollow $TiO_2$는 150-200 nm의 크기를 갖으며 20-30 nm 크기의 $TiO_2$ particle들로 이루어져 있다. hollow $TiO_2$ (150-200 nm)를 기존의 $TiO_2$ (10-20 nm) 층 위에 올려 염료감응형 태양전지의 electrode에 적용할 경우 기존의 $TiO_2$ 단층을 이용한 것보다 우수한 light-scattering 효과를 갖게 되어 광전 변환 효율 증가에 긍정적인 영향을 미칠 것이다. 본 연구에서는 hollow $TiO_2$의 광학적 특성 및 결정성이 염료감응형 태양전지에 미치는 영향을 조사하였다. hollow $TiO_2$의 광학적 특성 및 결정성의 변화를 위하여 microwave hydrothermal 법의 합성 온도 및 합성시간에 변화를 주었다. hollow $TiO_2$의 광학적 특성은 UV-visible spectrometer를 이용하여 조사하였으며, hollow $TiO_2$의 형상과 결정학적 특성은 TEM과 SEM 그리고 X선 회절 분석을 이용하여 관찰되었고, hollow $TiO_2$의 비표면적 측정은 BET 측정법을 이용하였다. 또한 염료감응형 태양전지 cell을 제작하여 $100mW/cm^2$(AM 1.5G) 기준에서 광전 변환 효율을 측정하였다.