• Journal of Hydrogen and New Energy
• /
• v.25 no.3
• /
• pp.280-288
• /
• 2014

SDC (Samarium doped Ceria) electrolyte was developed for Intermediate temperature SOFC ($500^{\circ}C-800^{\circ}C$) which showed a good electrical conductivity. In this study, we used sintering aids to reduce the SDC sintering temperature down to $1000^{\circ}C$, especially which can help the SOFC scale-up. In order to reduce the SDC sintering temperature, $Li_2CO_3$ and $TiO_2$ were used as a sinering aids for decreasing sintering temperature. $Li_2CO_3$ and $TiO_2$ doped SDC sintered at $1000^{\circ}C$ showed 99% of the theoretical density and higher electrical conductivity than the pure SDC sintered at $1500^{\circ}C$. When measuring the OCV (Open circuit voltage) with the $Li_2CO_3$ and $TiO_2$ doped SDC electrolyte, however, the OCV values were lower than the theoretical OCV values which means that the modified SDC still had electronic conductivity.

• Analytical Science and Technology
• /
• v.9 no.2
• /
• pp.161-167
• /
• 1996

An investigation was made of possible ways in which one could control the relative rates of cadmium deposition and hydrogen evolution by binary additive systems. Benzyl alcohol was employed as an additives due to its ability to form a hydrophobic film which inhibit the electroreduction of water to form hydrogen. The second additive was chosen to make the cadmium(II) ion less hydrophilic and increase its ability to cross the hydrophobic benzyl alcohol film and be electrodeposited at the cathode. It was shown by voltammetric and current efficiency studies that ion pairing and complexing additives could be used to accelerate the reduction of cadmium in the presence of the benzyl alcohol film. It was also shown that the benzyl alcohol film lowered the dielectric constant of the solution near the electrode enough to obtain ion pairing between the sodium ion and the negative chloride complex of cadmium and accelerate the reduction of the cadmium. This acceleration did not occur in the sulfate solution in the absence of chloride since cadmium(II) is primarily present as a positive aquo complex and ion pairing, if it occured, would not accelerate but would hinder reduction of cadmium.

• Journal of the Korean Chemical Society
• /
• v.33 no.6
• /
• pp.607-613
• /
• 1989

The chemical equilibria of Ni(II)-tetraamine (tetraamine = 2,12-dimethyl-3,7,11,17-tetraazabicyclo-11,3,1-heptadeca-1(17),2,11,13,15-pentaene) complex ion in water, acetonitrile, acetone and nitromethane were investigated using spectrophotometric method, respectively. The equilibria between low-spin ($D_{4h}$) and high-spin ($O_h$) structures of Ni-tetraamine complex ion were presented in water, acetonitrile and acetone, but not in nitromethane. The eqilibrium constants, the reaction enthalpies and the reaction entropies were determined from analysis of the temperature dependence of the electronic spectra. The formation of the triplet species ($O_h$) was found to be exothermic. The solvent and electrolyte effects on the equilibrium constants could be explained by the dielectric constants of solvents and the reaction entropies.

• Applied Chemistry for Engineering
• /
• v.25 no.6
• /
• pp.592-597
• /
• 2014

The graphite/$SiO_2$ composites as anode materials for lithium-ion batteries were prepared by sol-gel method to improve the graphite's electrochemical characteristics. The prepared graphite/$SiO_2$ composites were analysed by XRD, FE-SEM and EDX. The graphite surface modified by silicon dioxide showed several advantages to stabilize SEI layer. The electrochemical characteristics were investigated for lithium ion battery using graphite/$SiO_2$ as the working electrode and Li metal as the counter electrode. Electrochemical behaviors using organic electrolytes ($LiPF_6$, EC/DMC) were characterized by charge/discharge, cycle, cyclic voltammetry and impedance tests. The lithium ion battery using graphite/$SiO_2$ electrodes had better capacity than that of using graphite electrodes and was able to deliver a discharge capacity with 475 mAh/g at a rate of 0.1 C. Also, the capacity retention ratio of the modified graphite reaches 99% at a rate of 0.8 C.

• Journal of the Korean Chemical Society
• /
• v.50 no.4
• /
• pp.307-314
• /
• 2006

The redox characteristics of 2-ketohydrazono-3-phenyl-5-substituted-2,3-dihydro-1,3,4-thiadiazoles and its derivatives (1a-h) has been investigated in nonaqueous solvents such as 1,2-dichloroethane (DCE), dichloromethane (DCM), acetonitrile (AN), tetrahydrofuran (THF), and dimethylsulfoxide (DMSO) containing 0.1 mol.dm-3 tetra n-butylammonium perchlorate (TBAP) as supporting electrolyte at platinum ectrode. Through controlled potential electrolysis, the oxidation and reduction products of the investigated compounds can be separated and indentified. The redox mechanism is suggested and proved. It was found that all the investigated compounds are oxidized in two irreversible one-electron processes following the well known pattern of EC-mechanism. On the other hand, these compounds are reduced in a single two electron or in a successive two one electron processes following the well known pattern of EEC-mechanism according to the nature of the substituent

• KSBB Journal
• /
• v.8 no.3
• /
• pp.200-208
• /
• 1993

As a separation membrane for water-ethanol mixtures, alginic acid has been used which is hydrophilic polysaccharide and has excellent bonding capacity with divalent metal ions. Pervaporation characteristics of the alginic acid membrane were examined. The membrane was crosslinked with metal ions for the improvement of mechanical strength and chemical affinity. And its pervaporation characteristics were investigated. The first group(I A) metal complexed membrane cannot be used because of their brittleness and excessive swelling in low concentrations of ethanol solution. But the permeation characteristics of other metal complexed membrane were more improved than that of the alginic acid membrane because of their contraction of the membrane and hydrophilic property of metal ion.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.330-333
• /
• 2019

Various studies on dye-sensitized solar cells, which are cheaper to manufacture and have superior stability than silicon solar cells, are continuously conducted. In this study, the properties of dye-sensitized solar cells were studied using semiconductor oxides made by mixing $TiO_2$ and $Nb_2O_5$. By adding $Nb_2O_5$ in different proportions, the solar cell was made, and the surface area and electrical characteristics of this cell were measured. As $Nb_2O_5$ was added, the contact area of dye and electrolyte increased and the short-circuit current, open voltage, fill factor and conversion efficiency of dye-sensitized solar cells were confirmed to be improved.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.1
• /
• pp.71-75
• /
• 2022

Graphene oxide was stirred with a ZnCl₂:NaCl electrolyte and electrochemically coated by cyclic voltammetry to simplify the electron transpfer layer film forming process for organic solar cells and to fabricate an organic solar cell having it. The device structure is FTO/ZnO:graphene/P3HT:PCBM/PEDOT:PSS/Ag. Morphology and chemical properties of ETL were confirmed by scanning electron microscopy(SEM), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. As a result of XPS measurement, ZnO metal oxide and carbon bonding were simultaneously confirmed, and ZnO and graphene peaks were confirmed by Raman spectroscopy. The electrical characteristics of the manufactured solar cell were specified with a solar simulator, and the ETL device coated twice at a rate of 0.05 V/s showed the highest photoelectric conversion efficiency of 1.94%.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.5
• /
• pp.259-266
• /
• 2022

In this study, we developed a deep learning and vision sensor-based assembly performance evaluation method isfor prefabricated steel structures. The assembly parts were segmented using a modified version of the receptive field block convolution module inspired by the eccentric function of the human visual system. The quality of the assembly was evaluated by detecting the bolt holes in the segmented assembly part and calculating the bolt hole positions. To validate the performance of the evaluation, models of standard and defective assembly parts were produced using a 3D printer. The assembly part segmentation network was trained based on the 3D model images captured from a vision sensor. The sbolt hole positions in the segmented assembly image were calculated using image processing techniques, and the assembly performance evaluation using the k-nearest neighbor algorithm was verified. The experimental results show that the assembly parts were segmented with high precision, and the assembly performance based on the positions of the bolt holes in the detected assembly part was evaluated with a classification error of less than 5%.

• Journal of Hydrogen and New Energy
• /
• v.35 no.2
• /
• pp.140-145
• /
• 2024

High temperature co-electrolysis of H₂O-CO₂ mixtures using solid oxide cells has attracted attention as promising CO₂ utilization technology for production of syngas (H₂/CO), feedstock for E-fuel synthesis. For direct supply to E-fuel production such as hydrocarbon and methanol, the outlet gas ratio (H₂/CO/CO₂) of co-electrolysis should be controlled. In this work, current voltage characteristic test and product gas analysis were carried out under various reaction conditions which could attain proper syngas ratio.