• Journal of the Korean Magnetics Society
• /
• v.6 no.4
• /
• pp.242-250
• /
• 1996

The effects of annealing in magnetic field after deposition on electromagnetic properties of $Ni_{81}Fe_{19}$ thin($400\;{\AA}$) films prepared by RF-magnetron sputtering were investigated in terms of microstructure and surface morphology. The coercivity of the films was decreased below $300^{\circ}C$ due to stress relief and recrystallization, while increased at $400^{\circ}C$ due to grain growth and increasing the surface roughness. And then, $4{\pi}M_{s}$, was almost independent of annealing temperatures. Increasing the annealing temperature. the electrical resistivity of films was decreased from $37\;{\mu}{\Omega}cm$ to $24\;{\mu}{\Omega}cm$, the magnetoresistance was nearly a constant of about $0.6\;{\mu}{\Omega}cm$, and the MR ratio was increased from 1.5 % to 3.1 %. Therefore, It was shown that increasing the magnetoresistive ratio was mainly affected by decreasing the electrical resistivity. Considering the practical application of the films for magnetoresistive heads, optimal annealing conditions was obtained after one hour annealing at $300^{\circ}C$ in 400 Oe unidirectional magnetic field.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.11a
• /
• pp.11-11
• /
• 2000

이동통신기술의 급격한 발달로 고주파회로의 packaging과 interconnect 기술의 고성능화 와 저가격화에 대한 새로운 도전이 요구되고 있다‘ 대부분 기존의 무선통신 부품은 P PCB(Printed Wiring Board)기술을 활용하고 있으나 이러한 기술이 점차로 고주파화되는 경 향을 만족시킬수 없어 새로운 고주파 부품기술이 요구되고 있는 실정이다 .. RF 회로를 구성 하기 위하여 PCB소재의 환경적, 치수안정성 문제를 극복하기 위하여 L TCC(Low T Temperature Cofired Ceramics)기술이 최근 주목을 받고 있다. 차세대 이동통신 기술은 수십 GHz 이상의 고주파특성이 우수하고, 고성능의 초소형의 부품을 저가격으로 제조할수 있으며, 시장의 변화에 기민하게 대처할수 있는 기술이 요구되 고 있으며, 이러한 기술적 필요성에 부합할수 있도록 LTCC 기술이 제안되었다. 이러한 C Ceramic Interconnect 기술은 높은 신뢰성을 바탕으로 fine patterning 기술과 저가의 m metallizing 기술로 가능하게 되었다. 초고주파 통신부품기술은 미국과 유럽 등을 중심으로 G GHz 대역또는 mm wave 대역의 기술에 대하여 치열한 기술개발 경쟁을 벌이고 있으며, 이 러한 고주파 패키징 기술을 바탕으로 미래의 군사, 항공, 우주 및 이동통신 기술에 지대한 영향을 미칠수 있는 기반기술로 자리잡을 전망이다. L LTCC 기술은 기존의 후막혼성기술에 비하여 공정이 단순하고 대량생산이 가능하고 가 격이 비교적 저렴하다. 또한 다층구조로 제작할수 있고, 수동소자를 내장할수 있어 회로의 소형화와 고밀도화가 가능하다. 특히 무선으로 초고속 정보를 처리하기 위하여 이동통신기 기의 고주파화가 빠르게 진행됨에 따라서 고분자재료에 비하여 고주파특성이 우수할뿐아니 라 환경적, 치수안정성이 우수한 세라믹소재플 사용함으로써 고주파 손실율을 저감할 수 있 다 .. LTCC 기술은 후막회로 기술과 tape dielectric 기술이 결합된 기술이다. 표준화된 소재 와 공정기술을 활용하여 저가격으로 고성능소자플 제작할 수 있으며, 전극재료로서 높은 전 도도를 갖고 있는 Ag, Cu, Au 및 Pd! Ag릎 사용함으로써 고주파 손실을 저감시킬 수 있다. L LTCC 기술이 최종적으로 소형화, 고기능 고주파 부품기술로 지속적으로 발전하기 위하여 무수축(Zero shrinkage) 소성기술, 광식각 후막기술 등이 원천기술로서 확립될 수 있어야 하 며, 특히 국내의 이동통신 기술에 대한 막대한 투자에도 불구하고 차세대 이동통신 부품기 술에 대한 개발은 상대적으로 미흡한 실정이므로 국내에 LTCC 관련 소재공정 및 부품소자 기술에 대한 개발투자가 시급히 이루워져야 할 것으로 판단된다. 본 발표에서는 지금까지 국내외 LTCC 기술의 발전과정을 정리하였고, 현재 이 기술의 응용과 소재와 공정을 중심으로한 개발현황에 대하여 조사하였으며, 앞으로 LTCC가 발전 해야할 방향을 제시하고자 한다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.5
• /
• pp.25-36
• /
• 2016

The goal of the SmartGrid is to maximize energy efficiency by exchanging bi-directional real-time power information with the help of ICT(Information and Communication Technology). In this paper, we propose a "JRS-MS" (Joint Routing and Scheduling for Multi-channel SmartGrid) algorithm that uses numerical modeling methods in IEEE 802.11s based STDMA multi-channel SmartGrid NAN networks. The proposed algorithm controls the amount of data transmission adaptively at the link layer and finds a high data-rate path which has the least interference between traffic flows in multi-channel SmartGrid NAN networks. The proposed algorithm improve transmission performance by enhancing network utilization. By comparing the results of performance analysis between the proposed algorithm and the JRS-SG algorithm in the previous paper, we showed that the JRS-MS algorithm can improve transmission performance by maximally utilizing given network resources when the number of flows are increasing in the multi-hop NAN wireless mesh networks.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.8
• /
• pp.74-85
• /
• 2015

PCI Express is a well-known and widely used de-facto system bus standard for connecting among a processor and IO devices. PCI Express is originated from old PCI standard, and its most of applications are limited to be used within a PC or server system. But, because of its fast speed, low power consumption, and good protocol efficiency, it is considered as one of a good candidate for an alternate system interconnect for many years. In this paper, we present design, implementation and early evaluation of an alternate system interconnect by utilizing PCI Express. The developed alternate system interconnect using PCI Express (named PCIeLINK) utilizes non-transparent bridging (NTB) technic which generally used in fail-over system in PCI and PCI Express. By using NTB technic, PCI Express device can be extended to outside of a system without electrical and logical problems arising during system boot and enumeration. To build up an alternate system interconnect, we designed and implemented a network interface card having multiple PCI Express ${\times}4$ connections (theoretically 20 Gbps) and tested, The early test results revealed that an ${\times}4$ port in the card showed 8.6 Gbps peak performance for bulk transmission and 5.1 Gbps peak for normal TCP/IP transfer.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.2
• /
• pp.61-71
• /
• 2009

In this paper, we propose a low-cost and compact motion capture system which enables to play motion games in PS2(Play Station 2). Recently, motion capture systems which are being used as a part in film producing and making games are too expensive and enormous systems. Now days, motion games using common USB camera are slow and have two-dimension recognition. But PSD sensor has a few good points, such as fast and low-cost. In recently year, 3D motion capture systems using 2D PSD (Position Sensitive Detector) optic sensor for motion capturing have been developed. One is Multi-PSD motion capture system applying stereo vision and another is Single-PSD motion capture system applying optical theory ship. But there are some problems to apply them to motion games. The Multi-PSD is high-cost and complicated because of using two more PSD Camera. It is so difficult to make markers having omni-direction equal intensity in Single-PSD. In this research, we propose a new theory that solves aforementioned problems. It can measure 3D coordination if separated two marker's intensity is equal to. We made a system based on this theory and experimented for performance capability. As a result, we were able to develop a motion capture system which is a single, low-cost, fast, compact, wide-angle and an adaptable motion games. The developed system is expected to be useful in animation, movies and games.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.3
• /
• pp.7-17
• /
• 2010

In this paper, an innovative low-power SRAM based on 4-transistor latch cell is described. The memory cells are composed of two cross-coupled inverters without access transistors. The sources of PMOS transistors are connected to bitlines while the sources of NMOS transistors are connected to wordlines. They are accessed by totally new read and write method which results in low operating power dissipation in the nature. Moreover, the design reduces the leakage current in the memory cells. The proposed SRAM has been demonstrated through 16-kbit test chip fabricated in a 0.18-${\mu}m$ CMOS process. It shows 17.5 ns access at 1.8-V supply while consuming dynamic power of $87.6\;{\mu}W/MHz$ (for read cycle) and $70.2\;{\mu}W/MHz$ (for write cycle). Compared with those of the conventional 6-transistor SRAM, it exhibits the power reduction of 30 % (read) and 42 % (write) respectively. Silicon measurement also confirms that the proposed SRAM achieves nearly 64 % reduction in the total standby power dissipation. This novel SRAM might be effective in realizing low-power embedded memory in future mobile applications.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.2
• /
• pp.118-124
• /
• 2008

For forward error correction, DVB-S2, which is the digital video broadcasting forward error coding and modulation standard for satellite television, uses a system based the concatenation of BCH with LDPC inner coding. In DVB-S2 the LDPC codes are defined for 11 different code rates, which means that a DVB-S2 LDPC decoder should support multiple code rates. Seven of the 11 code rates, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, and 9/10, are regular and the rest four code rates, 1/4, 1/3, 2/5, and 1/2, are irregular. In this paper we propose a flexible decoder for the regular LDPC codes. We combined the partially parallel decoding architecture that has the advantages in the chip size, the memory efficiency, and the processing rate with Benes network to implement a DVB-S2 LDPC decoder that can support multiple code rates with a block size of 64,800 and can configure the interconnection between the variable nodes and the check nodes according to the parity-check matrix. The proposed decoder runs correctly at the frequency of 200MHz enabling 193.2Mbps decoding throughput. The area of the proposed decoder is $16.261m^2$ and the power dissipation is 198mW at a power supply voltage of 1.5V.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.32 no.3
• /
• pp.338-345
• /
• 2003

Response surface methodology was used for monitoring changes in phenolic compounds properties of Rubi Fructus extract depening on extraction conditons. The three independent variables (extraction conditions) were ratio of solvent to sample content (5, 10, 15 mL/g), ethanol concentration (20, 40, 60%) and extraction time (2, 4, 6 hr). It was anticipated that each of the five dependent Y variables (responses) would be affected by the three independent variables. The dependent responses were total yield, total phenolics content, electron donating ability, antioxidant ability and nitrite-scavenging ability (pH 1.2, 3.0, 4.2, 6.0). Total yield, total phenolics content, electron donating ability and antioxidant ability were affected by ratio of solvent to sample content. Nitrite- scavenging ability at pH 1.2 and pH 6.0 was affected by ethanol concentration, while it was affected by extraction time at pH 3.0 and pH 4.2. The optimum extraction conditions for total yield were 14.16 mL/g ratio of solvent to sample content,39.08% ethanol concentration and 2.99 hr extraction time. The maximum total phenolics content of extracts were shown at 14.06 mL/g ratio of solvent to sample content, 35.51% ethanol concentration and 3.15 hr extraction time.

• Food Science of Animal Resources
• /
• v.32 no.5
• /
• pp.669-677
• /
• 2012

The objective of this study was to analyze the flavor pattern of different varieties of cheeses. Four of the each following cheese varieties such as shred type pizza cheese, Cheddar cheese, Mozzarella block cheese, and white mold-ripened cheeses, stored at $4^{\circ}C$ during 2 wks were examined before and after cooking at $70^{\circ}C$ and $160^{\circ}C$. Flavor patterns of these cheeses were analyzed using an electronic nose system based on mass spectrometer. All data were treated by multivariate data processing based on discriminant function analysis (DFA). The results showed the discriminant model by DFA method. Data revealed that flavor patterns of pizza cheeses were well separated as storage prolonged and obviously discriminated as the higher the cooking temperature. The result of pattern recognition analysis based on discriminant function analysis showed that new brand of pizza cheese produced by Imsil Cheese Cooperative was located at middle between the flavors of the imported brands of pizza cheese and those of domestic brand of pizza cheeses. Imsil cheese has a unique flavor pattern among other variety of cheeses. Application of pattern recognition analysis by electronic nose might be useful and advanced technology for characterizing in flavor pattern of cheese products from different origins and different categories of cheeses.

• Korean Journal of Food Science and Technology
• /
• v.42 no.5
• /
• pp.527-532
• /
• 2010

The properties of volatile flavor components were compared in commercial brown rice vinegars that were fermented with and without ethanol addition, for which solid phase microextraction-gas chromatography (SPME-GC), electronic nose, and sensory evaluations were performed. A total of 24 volatile compounds, mainly composed of acetic acid, ethyl acetate, benzaldehyde, iso-valeric acid, phenylethyl alcohol, 2-phenylethyl acetate, acetoin, and isobutyric acid, were identified in the brown rice vinegar fermented without ethanol, while major volatiles in the brown rice vinegar fermented with ethanol were acetic acid, ethyl acetate, 1-hexyl acetate, benzaldehyde, 2-phenylethyl acetate, and phenylethyl alcohol. The electronic nose patterns of samples indicated a significant difference in the brown rice vinegars fermented with and without ethanol. Pungent flavor and off-flavor intensity were high in the brown rice vinegar fermented without ethanol. According to the results, fermentation conditions affect the volatile properties of brown rice vinegars.