• Journal of Biomedical Engineering Research
• /
• v.25 no.2
• /
• pp.137-144
• /
• 2004

ECG signals are often contaminated with high-frequency noise such as muscle artifact, power line interference, and others. In the ECG signal processing, especially during a pre-processing stage, numerous noise removal techniques have been used to reduce these high-frequency noise without much distorting the original signal. This paper proposes a new type of digital filter with a continuously variable cutoff frequency to improve the signal quality This filter consists of a cutoff frequency controller (CFC) and variable cutoff frequency lowpass filter (VCF-LPF). From the noisy input ECG signal, CFC produces a cutoff frequency control signal using the signal slew rate. We implemented VCF-LPF based on two new filter design methods called convex combination filter (CCF) and weight interpolation fille. (WIF). These two methods allow us to change the cutoff frequency of a lowpass filter In an arbitrary fine step. VCF-LPF shows an excellent noise reduction capability for the entire time segment of ECG excluding the rising and falling edge of a very sharp QRS complex. We found VCF-LPF very useful and practical for better signal visualization and probably for better ECG interpretation. We expect this new digital filter will find its applications especially in a home health management system where the measured ECG signals are easily contaminated with high-frequency noises .

• Analytical Science and Technology
• /
• v.15 no.3
• /
• pp.236-242
• /
• 2002

A method was investigated to determine the thickness of coating on steel sheet using rf glow discharge atomic emission spectrometer. The RF gas-jet boosted glow discharge has such salient feature as good pleasure stability and high sputtering efficiency that it was possible to determine the thickness of silicon resin film on zinc electroplated steel. The erosion speed variation is dependent on discharge power, gas flow rate and discharge pressure. therefore determine discharge condition to measure the thickness of coating on steels. The fundamental studies have been carried out to investigate an optimum condition for in-depth analysis and composition of zinc coating on steel. In this study, the calibration curve for thickness determination of silicon resin film was found to be linear in the range of $1000{\sim}3500mg/m^2$ film thickness. The developed rf gas-jet boosted glow discharge was applied to the analysis of zinc coating and silicon resin film on steel made by RIST.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5513-5521
• /
• 2015

There is an operational efficiency problem about wayside equipment applied to the domestic low-density branch as the equipment has been installed and operated similarly in the mainline. On-board oriented train control system, which has been developed for train safety and operation efficiency, ensures safe train operation without expensive ground control signal devices. Such system consists of on-board control system, wayside control system, and local control system. In this paper, the details of tests such as suitability test, communication test, and interface test are described by installing the on-board control system and wayside control system in field. Installation tests include checking power, voltage, cable connection, LED status, etc. Field applicability of the developed system is also verified through the dynamic operation tests with diverse scenarios, which are performed on the virtual line similar to the real environment including switch machine and level crossing gate. Dynamic operation tests were conducted for total 7 scenarios, and several tests were repeated for each scenario. The elapsed time for each operation was computed by analyzing main process log, and we could check that each operation was accomplished within several seconds. Furthermore, the developed system was verified through field test with an accredited institute, and testing certificates were issued.

• Journal of Energy Engineering
• /
• v.26 no.3
• /
• pp.51-63
• /
• 2017

Paris Agreement on Climate Change(2015) requires to reduce the greenhouse gas emission. One of the responses to the requirement is to change the proportion of power generation, which is summarized to the decrease in thermal power and the increase in new and renewable power. This article conducts a comparative analysis on the economic effects between thermal- and new and renewable- power generations, using the Input-Output Table from The Bank of Korea. The results of this analysis show that the new and renewable power generation has got the larger effects in production-inducing, value-added-inducing, employment-inducing, and supply-shortage scopes, while the smaller effect in price-pervasive scope than the thermal power generation. According to these results, the complex consideration should be taken into when the changes in power generation mix are tried. Especially, the political efforts to reduce the supply-shortage effect of new and renewable power and the price-pervasive effect of thermal power will be important.

• Journal of Energy Engineering
• /
• v.29 no.1
• /
• pp.1-12
• /
• 2020

The rapid climate change is strengthening carbon emissions regulations internationally. Korea is strongly pressed to accept the obligation to reduce greenhouse gases as one of the United Nations Framework Convention on Climate Change. This article analyzed the Granger causalities among environmental regulation, economic growth, electricity consumption, and CO₂ emission in Korea, using unit root test, cointegration test, and vector error correction model. As the results, environmental regulation has shown the bidirectional causalities with electricity consumption and CO₂ emission, while being unilaterally affected by economic growth in the long-run and strong relationship. Economic growth has affected electricity consumption, CO2 emission, and environmental regulation in the long-run, in the complex structure of the unilateral and short-run causality with electricity consumption and the bidirectional causality with CO2 emission. The policy implications will be as follows: ① environmental regulation should induce sustainable growth through encouraging technological innovation relating to CO2 reduction and productivity enhancement. ② Responding to the international CO2 reduction regulation, the synthetic policy initiatives will be considered to make synergy effects among policies relating to economic growth, electricity consumption.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.18 no.1
• /
• pp.16-29
• /
• 2016

The total area of paddy field was estimated to be 55 % of the cultivated lands in South Korea, which is approximately 1 million hectares. Organisms inhabiting paddy fields if they are sensitive to environmental changes can be environmental indicator of paddy fields. Biological indicators such as phenology and distributional range are evaluated as intuitive and quantitative method to analyze the impact of climate change. This study aims to estimate flight time change of Hydrophilidae species' based on the RCP 8.5 climate change scenario. Unmanned monitoring systems were installed in Haenam, Buan, Dangjin and Cheorwon relative to the latitudinal gradient. In the three regions excepting Cheorwon, it was able to measure the abundance of flying Hydrochara affinis and Sternolophus rufipes. Degree-day for the flight time was determined based either on field measurement values and estimates of 2020s, 2050s and 2080s from KMA climate change scenario data. As a result, it is found that date of both species of initial flight becomes 15 days earlier, that of peak flight becomes 22 days earlier and that of final flight does 27 days earlier in 2080s compared to 2020s. The climate change impact on flight time is greater in coastal area, rural area and valley than inland area, urban area and plan. H. affinis and S. rufipes can be used as climate change indicator species.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.140-140
• /
• 2016

유기전계발광소자 (Organic Light Emitting Diode : OLED)는 보조광원이 필요 없고 천연색 표현이 가능하며, 낮은 소비 전력 및 저전압 구동 등의 장점으로 이상적인 디스플레이 구현이 가능하여 차세대 디스플레이로써 많은 이목을 끌고 있으나 제한된 수명과 안정성의 문제점을 안고 있다. 따라서 OLED의 열화 원인을 분석하고 수명을 연장하기 위한 체계적인 방법과 기술 개발이 중요하다. Impedance Spectroscopy는 이온, 반도체, 절연체 등의 벌크 또는 계면 영역의 전하 이동을 조사하는데 사용될 수 있어, OLED에서도 Impedance Spectroscopy를 이용하여 전하수송과 전자주입 메커니즘 등 폭넓은 전기적 정보를 얻을 수 있다. 본 연구에서는 Impedance Spectroscopy를 이용하여 경과시간에 따른 OLED의 임피던스 특성을 측정하여 열화 메커니즘을 분석하였다. 본 연구에서 OLED는 ITO / 2-TNATA (4,4,4-tris2-naphthylphenyl-aminotriphenylamine) / NPB (N,N'-bis-(1-naphyl)-N, N'-diphenyl-1,1'- biphenyl-4,4'-diamine) / Alq3 (tris(quinolin-8-olato) aluminum) / Liq / Al으로 구성된 녹색 형광 OLED를 제작하였다. OLED의 전계 발광 특성을 측정하기 위한 전원 인가장치로 Keithley 2400을 사용하여 전압과 전류를 인가하였고, 소자에서 발광된 휘도 및 발광 스펙트럼은 Photo Research사의 PR-650 Spectrascan을 사용하여 암실 환경에서 측정하였다. 임피던스 스펙트럼은 컴퓨터 제어 프로그래밍이 가능한 KEYSIGHT사의 E4990A를 사용하여 측정하였다. 임피던스 측정 전압은 0 V부터 2 V 간격으로 8 V까지, 주파수는 20 Hz에서 2 kHz의 범위로 설정하여 측정하였다. I-V-L과 임피던스 특성은 24 시간의 간격을 두고 실온에서 측정하였다. 그림은 경과시간에 따른 녹색 형광 OLED의 인가전압 2 V, 6 V의 Cole-Cole plot을 나타낸 것이다. 문턱전압 미만인 인가전압 2 V에서는 소자를 통하여 전류가 흐르지 않아 큰 반원 형태를 나타내었고, 시간이 경과함에 따라 소자 제작 직후엔 실수 임피던스의 최댓값이 $8982.6{\Omega}$에서 480 시간 경과 후엔 $9840{\Omega}$으로 약간 증가하였다. 문턱전압 이상인 인가전압 6 V에서는 소자 제작 직후 실수 임피던스의 최댓값이 $108.2{\Omega}$으로 작은 반원 형태를 나타내나 시간이 경과함에 따라 방사형으로 증가하는 것을 확인 할 수 있었고, 672 시간 경과 후엔 실수 임피던스의 최댓값이 $9126.9{\Omega}$으로 문턱 전압 미만 일 때와 유사한 결과를 나타내었다. 이러한 임피던스의 증가 현상은 시간이 경과함에 따라 OLED의 열화에 의한 것으로 판단된다.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.6
• /
• pp.67-76
• /
• 2005

This paper proposes a compact-sized surface myoelectric sensor for the myoelectric hand prosthesis. To fit the surface myoelectric sensor in the socket for the myoelectric hand prosthesis, the sensor should be a compact size. The surface myoelectric sensor is. composed of a skin interface and a single processing circuit that are mounted on a single package. The skin interface has one reference and two input electrodes, and the reference electrode is located in the center of two input electrodes. In this paper we propose two types of sensors with the circle- and bar-shaped reference electrode, but all input electrodes are the bar-shaped. The metal material of the electrodes is the stainless steel (SUS440) that endures sweat and wet conditions. Considering the conduction velocity and the median frequency of the myoelectric signal, we select the inter-electrode distance (IED) between two input electrodes as 18mm, 20mm, and 22 mm. The signal processing circuit consists of a differential amplifier with a band pass filter, a band rejection filter for rejecting 60Hz power-line noise, amplifiers, and a mean absolute value circuit. We evaluate the proposed sensor from the output characteristics according to the IED and the shape of the reference electrode. From the experimental results we show the surface myoelectric sensor with the 18mm IED and the bar-shaped reference electrode is suitable for the myoelectric hand prosthesis.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.12
• /
• pp.60-69
• /
• 2000

This paper describes a single-chip full-custom implementation of pipelined adaptive decision-feedback equalizer(PADFE) using a 0.25-${\mu}m$ CMOS technology for wide-band wireless digital communication systems. To enhance the throughput rate of ADFE, two pipeline stages are inserted into the critical path of the ADFE by using delayed least-mean-square(DLMS) algorithm. Redundant binary (RB) arithmetic is applied to all the data processing of the PADFE including filter taps and coefficient update blocks. When compared with conventional methods based on two's complement arithmetic, the proposed approach reduces arithmetic complexity, as well as results in a very simple complex-valued filter structure, thus suitable for VLSI implementation. The design parameters including pipeline stage, filter tap, coefficient and internal bit-width, and equalization performance such as bit error rate (BER) and convergence speed are analyzed by algorithm-level simulation using COSSAP. The single-chip PADFE contains about 205,000 transistors on an area of about $1.96\times1.35-mm^2$. Simulation results show that it can safely operate with 200-MHz clock frequency at 2.5-V supply, and its estimated power dissipation is about 890-mW. Test results show that the fabricated chip works functionally well.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.91-96
• /
• 2011

In this paper, a low-power direct-conversion transmitter based on current-mode operation, which satisfies the IEEE 802.15.4 standard, is proposed and implemented in a $0.13{\mu}m$ CMOS technology. The proposed transmitter consists of DACs, LPFs, variable gain I/Q up-conversion mixer, a divide-by-two circuit with LO buffer, and a drive amplifier. By combining DAC, LPF, and variable gain I/Q up-conversion mixer with a simple current mirror configuration, the transmitter's power consumption is reduced and its linearity is improved. The drive amplifier is a cascode amplifier with gain controls and the 2.4GHz I/Q differential LO signals are generated by a divide-by-two current-mode-logic (CML) circuit with an external 4.8GHz input signal. The implemented transmitter has 30dB of gain control range, 0dBm of maximum transmit output power, 33dBc of local oscillator leakage, and 40dBc of the transmit third harmonic component. The transmitter dissipates 10.2mW from a 1.2V supply and the die area of the transmitter is $1.76mm{\times}1.26mm$.