• Journal of the Korea Society of Computer and Information
• /
• v.14 no.2
• /
• pp.157-168
• /
• 2009

In this paper, a photovoltaic system is designed with a step up chopper and single phase PWM(Pulse Width Modulation) voltage source inverter. Where proposed Synchronous signal and control signal was processed by one-chip microprocessor for stable modulation. The step up chopper operates in continuous mode by adjusting the duty ratio so that the photovoltaic system tracks the maximum power point of solar cell without any influence on the variation of insolation and temperature because solar cell has typical voltage and current dropping character. The single phase PWM voltage source the inverter using inverter consists of complex type of electric power converter to compensate for the defect, that is, solar cell cannot be developed continuously by connecting with the source of electric power for ordinary use. It can cause the effect of saving electric power. from 10 to 20[%]. The single phase PWM voltage source inverter operates in situation that its output voltage is in same phase with the utility voltage. In order to enhance the efficiency of photovoltaic cells, photovoltaic positioning system using sensor and microprocessor was design so that the fixed type of photovoltaic cells and photovoltaic positioning system were compared. In result, photovoltaic positioning system can improved 5% than fixed type of photovoltaic cells. In addition, I connected extra power to the system through operating the system voltage and inverter power in a synchronized way by extracting the system voltage so that the phase of the system and the phase of single-phase inverter of PWM voltage type can be synchronized. And, It controlled in order to provide stable pier to the load and the system through maintaining high lurer factor and low output power of harmonics.

• Journal of the Korea Convergence Society
• /
• v.2 no.3
• /
• pp.7-14
• /
• 2011

This paper deals with the efficient management for the intelligent distribution system related with the renewable energy sources, using the wire-wireless monitoring and control device. This device is mainly composed of 2 sections. One is monitoring device with the Autobase S/W and the other is control device using PLC. This paper proposes a wire and wireless monitoring and control device which can monitor and control the 50Kw PV system installed remotely (about 1Km) in the campus of the Korea University of Technology and Education. By the analysis of PV output characteristic using the device proposed in this paper, it is confirmed that the device can contribute the maintenance of PV system and also the establishment of Smart Grid.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.8 no.5
• /
• pp.221-227
• /
• 2008

This paper is to show the designing for LED lights driver unit. The main purpose of driver designing is high electrical efficient performance and intelligent control LED driver. Nowadays, a lightning system with some of charactestics such as an environmentally friendly purposes with a possible reduction of electric power consumptions. We constitute a intelligent contron LED control system that helps to save an electric energy, and a communication system to control the system. This LED driver can be used for intelligent light control. This product expects to improve the light control by dimming instead of interlace on/off light control that increases the social cost such as car accidents and etc.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.1
• /
• pp.137-146
• /
• 2019

The ultrasonic phased arrays are used for treating tumors in the human body by the focus control of the acoustic pressure at the desired position. The magnitude and phase of the surface acoustic pressure in each ultrasonic transducer is controlled by the magnitude and phase of the applied voltage to it. In this paper, the relationship between the applied voltage and the surface acoustic pressure of the ultrasound transducer is modelled, and the desired voltage is realized by PWM technique. The validity of the proposed method is verified by computer simulation of the focus control of a ultrasonic phased array composed of 61 ultrasonic transducers.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.5
• /
• pp.951-958
• /
• 2019

For the power grid-connection of distributed generation, the output voltage of the distributed generation must be synchronized with the grid voltage before the grid-connection. In this paper, a vector control based synchronization algorithm was developed for grid linkage of three-phase inverters. A three-phase voltage inverter was designed and fabricated to verify the effectiveness of the developed algorithm. The main controller of the three-phase inverter was developed based on DSP, and the electrical level of the system was set to an electrical level that can be tested in the laboratory. Throughout the experiments, it was confirmed that the proposed algorithm could be used as a synchronization algorithm for grid-connection by showing that the output voltage of the three-phase inverter is synchronized with the grid voltage.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.1
• /
• pp.83-90
• /
• 2014

In this paper, we address the problem of designing and implementing an oil pump control system driven by a brushless DC (BLDC) motor. The proposed oil pump plays the role of providing fuel to the engine clutch and transmission of hybrid vehicles. Main consideration is given to enhancing response feature and accuracy of the oil pump by simplifying the controller that is driven by a BLDC motor under PWM voltage control, which is a standard control method for BLDC motors. The proposed control scheme also helps to increase efficiency and reliability of the oil pump system. To validate the performance of the proposed system, we conduct experiments on BLDC motor speed control and oil pump operations.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.6
• /
• pp.99-106
• /
• 2010

This paper proposes a novel design of enhanced auto light control system using PLC(Power Line Communication) and SMS(Short Message Service) to copy with emergent cases effectively. In the proposed system, the indoor sensing system is designed to send emergent messages to the users or system manager in case of fire or invasion, which may prevent secondary accident. In addition, data transmission using PLC may drastically decreases the number of lines. The experimental results show the effectiveness of the proposed system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.3
• /
• pp.258-266
• /
• 2007

When the magnetic levitation system(MAGLEV) initially rise, The MAGLEV has a weak point that is very large variation of the electric current. In this paper, The author applied the multi-loop-control to stably control the magnetic levitation system(MAGLEV). The gains of the control algorithm were selected based on pole locations formulated from a prototype Bessel transfer function model. The design incorporate tradeoffs in DC-to-DC converter hard-ware para-meters and pole locations. In order to confirm the superiority of the proposed pole selection md controller, MATLAB simulation and experiment results are presented.

• Proceedings of the KIPE Conference
• /
• 2015.11a
• /
• pp.225-226
• /
• 2015

이 논문에서는 ITER 초전도 코일 전원 장치 중 진공 용기내에 형성된 자장의 오차를 보정해주는 CCU/L 컨버터의 4 상한 운전을 위한 제어 알고리즘을 설명하고, 제어 알고리즘을 실제 컨버터에 적용하여 구현하였다. ITER CCU/L 컨버터는 4 상한 제어를 통해 영 전류 불연속 구간 없이 Correction Coil에 전압(${\pm}85V$), 전류(${\pm}10kA$)를 공급해야 하고, 이를 위해선 4 상한 운전을 위한 제어가 매우 중요하다. 4 상한 운전은 다섯 가지 모드에서 동작된다. 본 논문에서, 각 모드에 대해 설명하고, 컨버터가 각 모드에서 정상적으로 제어되는지 시뮬레이션 및 실제 시험을 통해 검증하였다.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.5
• /
• pp.71-78
• /
• 2004

An infrared remote control-type transcutaneous control device using a $\mu$-processor is design for the totally implantable middle ear system. An infrared light transmission model for the tissue of skin was introduced and then a radiant intensity and the required current of the infrared light emitting diode(IR LED) driving circuit at transmission part were calculated for the external control device. And the transmission part generates IR signal by the system's own data protocol which prevents interferences from other infrared remote controls of the household appliances. The control part of the implanted device was designed to analyze functions of the received infrared(IR) signal that indicate the power ON/OFF and volume UP/DOWN. After the system is implemented, a data transmission experiments using 4 mm thickness of porcine skin were carried out. From the experiment, it was verified that the infrared control signal was transmitted to receiving module of the implemented system without any error.