• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.3
• /
• pp.300-304
• /
• 2012

This paper presents a nonlinear observer design method for SOC(state-of-charge) estimation of Lithium polymer battery cell. The dynamic equation of the battery cell is modeled as a simple RC electrical circuit with a nonlinear voltage source and the parameters are obtained via nonlinear optimization. Using the sum of squares decomposition, the observer gain is designed such that the error dynamics is asymptotically stable and the decay rate is below the prescribed value. In order to illustrate the performance of the observer, a computer simulation is performed using the experimental data with the UDDS(urban dynamometer driving schedule) current profile.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.4
• /
• pp.363-372
• /
• 2005

This paper presents an improved sensorless vector control system for high performance induction motor drives fed by a matrix converter with non-linearity compensation. The nonlinear voltage distortion that is caused by commutation delay and on-state voltage drop in switching devices is corrected by a new matrix converter model. A Reduced Order Extended Luenberger Observer (ROELO) is employed to bring better response in the whole speed operation range and a method to select the observer gain is presented. Experimental results are shown to illustrate the performance of the proposed system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.3
• /
• pp.220-226
• /
• 2000

The piezoelectric material for piezoelectric transformer needs the high electromechanical coupling factor( $k_{p}$) the piezoelectric constant( $d_{33}$) and the mechanical quality factor( $Q_{m}$)in order to obtain high voltage step-up ratio and low temperature rising. In this study the piezoelectric transformers were fabricated using Pb［$Zr_{0.45}$/ $Ti_{0}$48//L $u_{0.02}$(M $n_{1}$3//S $b_{2}$3/)$_{0.05}$］ $O_3$(PMS-PZT) and Pb［Z $r_{0.25}$/ $Ti_{0.375}$(M $g_{1}$3//N $b_{2}$3/)$_{0.375}$］ $O_3$+0.5wt%Mn $O_2$(PMN-PZT) ceramics. The piezoelectric properties of PMS-PZT and PMN-PZT were measured. The voltage set-up ratios of the piezoelectric transformers using PMS-PZT and PMN-PZT were the value of 15, 20 respectively under 100$_{KΩ}$ in Rosen type transformer.r.ormer.r.r.r.r.r.r.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.1 no.3
• /
• pp.41-47
• /
• 2008

This paper describes a wearable electro-stethoscope module for home-healthcare system. The module is consisted of a microphone, an instrumentation amplifier, a filter, a power amplifier etc. and is light and small. The phonogram signal from the module shows good performance. The test for the material and size of the sound collector of the chest piece is performed and the results is reflected on the prototype product. If the module is connected to wired or wireless communication network, so people can check their health without going hospital.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.10
• /
• pp.2045-2051
• /
• 2009

A 5-GHz band Low Noise Amplifier(LNA) using SOI MOSFET is designed. To improve the noise performance, depletion-type SOI MOSFET is adopted, and it is designed by the two-stage topology consisting of common-source and common-gate stages for low-voltage operation. The fabricated LNA achieved an S11 of less than -10dB, voltage gain of 21dB with a power consumption of 8.3mW at 5.5GHz, and a noise figure of 1.7dB indicated that the depletion-type LNA improved the noise figure by 0.3dB compared with conventional type. These results show the feasibility of a CMOS LNA employing depletion-type SOI MOSFET for low-noise application.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.3
• /
• pp.231-239
• /
• 1999

An improved version of current-regulated delta modulator (CRDM) is investigated for the output cunent control of v voltage-source inverters that have transformer-coupled series resonant load and are operated at the resonant frequency. Conventional CRDM has not only CUlTent offset problem but also transformer flux saturation problem when i it is applied to induction heating systems that have transformel-coupled loads. To cope with these problems, the effect of flux saturation is analysed, and simple method to av이d the problem is proposed. And integral type of CRDM is a adopted to remove the cunent offset. The boundaries of integrator gain for stable operation is calculated using the c concept of sliding mode controL The validity of proposed strategy is vel퍼ed through simulations and prototype e experiments.

• Proceedings of the KIPE Conference
• /
• 2008.10a
• /
• pp.29-32
• /
• 2008

최근 PDP Display 시장은 해를 거듭 할수록 가격 경쟁이 치열해 지고 있다. 그에 따라 PSU(Power Supply Unit) 모듈의 저 가격화 및 경량화가 요구되고 있고, 요구조건을 만족하기 위해 여러 출력을 하나로 통합화 하는 다 출력 구조의 변압기가 적용되고 있다. 본 논문에서는 서스테인 전원부($V_s$)와 어드레스 전원부($V_a$), 그리고 Multi 18V전원부($V_m$)를 하나의 변압기에 일체화 하였다. 그리고 어드레스 전원부($V_a$)와 Multi 18V전원부($V_m$)의 부하 추가에 따라 서스테인 전원부($V_s$)의 전압 이득 특성 및 공진특성 변화를 확인하였다. 또한 다 출력 LLC 직렬공진 컨버터 설계 시 고려사항과 동작 특성으로 42인치 HD PDP 전원에 적용하여 검증한 결과에 대하여 서술 하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.05a
• /
• pp.49-50
• /
• 2014

In this paper, a wideband loop antenna for UWB applications is studied. The proposed wideband loop antenna consists of a circular loop and circular sectors. Circular sectors with a ultra-wideband characteristic are used to connect the circular loop and the center feed points. Optimal design parameters are obtained by analyzing the effects of the gap between the circular sectors and the radius of the circular loop on the input reflection coefficient and gain characteristics. The optimized wideband loop antenna is fabricated on an FR4 substrate with a dimension of $41mm{\times}41mm$. Experimental results show that the antenna has a desired UWB characteristic with a frequency band of 3.1-11.0 GHz for a VSWR < 2.25.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.10
• /
• pp.34-39
• /
• 2016

A low-voltage, low-power analog front-end IC for neural recording implant devices is presented. The proposed IC consists of a low-noise neural amplifier and a programmable active bandpass filter to process neural signals residing in the band of 1 Hz to 5 kHz. The neural amplifier is based on a source-degenerated folded-cascode operational transconductance amplifier (OTA) for good noise performance while the following bandpass filter utilizes a low-power current-mirror based OTA with programmable high-pass cutoff frequencies from 1 Hz to 300 Hz and low-pass cutoff frequencies from 300 Hz to 8 kHz. The total recording analog front-end provides 53.1 dB of voltage gain, $4.68{\mu}Vrms$ of integrated input referred noise within 1 Hz to 10 kHz, and noise efficiency factor of 3.67. The IC is designed using $18-{\mu}m$ CMOS process and consumes a total of $3.2{\mu}W$ at 1-V supply voltage. The layout area of the IC is $0.19 mm^2$.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.6
• /
• pp.23-36
• /
• 2005

PLLs have been widely used for many applications including communication systems. This paper presents a VCO with an improved negative skewed delay scheme and a PLL using this VCO. The proposed VCO and PLL are intended for replacing traditional LC oscillators and PLLs used in communication systems and other applications. The circuit designs of the VCO and PLL are based on 0.18um CMOS technology with 1.8V supply voltage. The proposed VCO employs subfeedback loops using pass-transistors and needs two opposite control voltages for the pass transistors. The subfeedback loops speed up oscillation depending on the control voltages and thus provide a high oscillation frequency. The two voltage controls have opposite frequency gain characteristics and result in low phase-noise. The 7-stage VCO in 0.18um CMOS technology operates from $3.2GHz\~6.3GHz$ with phase noise of about -128.8 dBc/Hz at 1MHz frequency onset. For 1.8V supply voltage, the current consumption is about 3.8mA. The proposed PLL has dual loop-filters for the proposed VCO. The PLL is operated at 5GHz with 1.8V supply voltage. These results indicate that the proposed VCO can be used for radio frequency operations replacing LC oscillators. The circuits have been designed and simulated using 0.18um TSMC library.