• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.9
• /
• pp.58-67
• /
• 2009

This paper presents a fully digital gain control system with a new high bandwidth and wide dynamic range power detector for DVB-S2 application. Because the peak-to-average power ratio (PAPR) of DVB-S2 system is so high and the settling time requirement is so stringent, the conventional closed-loop analog gain control scheme cannot be used. The digital gain control is necessary for the robust gain control and the direct digital interface with the baseband modem. Also, it has several advantages over the analog gain control in terms of the settling time and insensitivity to the process, voltage and temperature variation. In order to have a wide gain range with fine step resolution, a new AGC system is proposed. The system is composed of high-bandwidth digital VGAs, wide dynamic range power detectors with RMS detector, low power SAR type ADC, and a digital gain controller. To reduce the power consumption and chip area, only one SAR type ADC is used, and its input is time-interleaved based on four power detectors. Simulation and measurement results show that the new AGC system converges with gain error less than 0.25 dB to the desired level within $10{\mu}s$. It is implemented in a $0.18{\mu}m$ CMOS process. The measurement results of the proposed IF AGC system exhibit 80-dB gain range with 0.25-dB resolution, 8 nV/$\sqrt{Hz}$ input referred noise, and 5-dBm $IIP_3$ at 60-mW power consumption. The power detector shows the 35dB dynamic range for 100 MHz input.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.7
• /
• pp.635-645
• /
• 2016

In this paper, we showed the phase noise of voltage controlled oscillator(VCO) can be radically improved using FLL(Frequency Locked Loop). At first, a 5 GHz VCO is fabricated using a hair-pin resonator. The fabricated VCO shows a phase noise of -53.1 dBc/Hz at 1 kHz frequency offset. In order to improve the phase noise of the fabricated VCO, a FLL is constructed using the feedback loop that consists of the VCO, a frequency detector composed of 5 GHz resonator, loop-filter, and level shifter. The fabricated FLL is designed to oscillate at a frequency of 5 GHz, and its measured phase noise is about -120.6 dBc/Hz at 1 kHz offset frequency. As a result, the phase noise of VCO can be radically improved by about 67.5 dB applying FLL. In addition, the measured phase noise performance is close to that of crystal oscillator.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.67-73
• /
• 2015

This paper presents a fully integrated 3 - 5 GHz IR-UWB(impulse radio ultra-wide band) RFIC for Location based system. The receiver architecture adopts the energy detection method and for high speed sampling, the equivalent time sampling technique using the integrated DLL(delay locked loop) and 4 bit ADC. The digitally synthesized UWB impulse generator with low power consumption is also designed. The designed IR-UWB RFIC is implemented on $0.18{\mu}m$ CMOS technology. The receiver's sensitivity is -85.7 dBm and the current consumption of receiver and transmitter is 32 mA and 25.5 mA respectively at 1.8 V supply.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.675-677
• /
• 2009

통신기기에서 중요한 기술 중 하나인 PLL(Phase Locked Loop) 회로는 주기적인 신호를 원하는 대로, 정확한 고정점으로 잡아주는데 그 목적을 둔다. 일반적인 구조로 위상주파수검출기(Phase Frequency detector), 루프필터(Loop filter), 전압제어발진기(Voltage Controlled Oscillator), 디바이더(Divider)로 구성되어진다. 그러나 일반적인 PLL 구조로는 지터(jitter)가 증가하고 트랙(tracking) 속도가 느리다는 단점이 있다. 이를 보완하기 위해 루프필터 전단에 차지펌프(Charge pump) 회로를 추가하여 사용하고 있다. 본 논문에서는 CMOS를 이용한 PLL용 차지펌프를 설계하였다. 설계된 회로는 $0.18{\mu}m$ CMOS 공정 기술을 사용하여 CADENCE사의 Specter로 시뮬레이션 하였으며, Virtuso2로 레이아웃 하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.690-692
• /
• 2009

PLL은 위상주파수검출기(PFD), 차지펌프(Charge Pump), 루프필터(Loop Filter), 전압제어발진기(VCO), Divider로 구성하고 있는데 본 논문에서는 설계된 차지펌프 PLL을 시뮬레이션을 해보고 그 결과를 정리하고 레이아웃(layout)까지 하였다. 차지펌프 설계에 있어서 전류 부정합, 전하 공유, 전하주입, 누설 전류등을 고려할 필요가 있다. 설계된 차지펌프는 전류 부정합을 감소시키기 위해 전류뺄셈회로를 이용하여 전류 부정합을 감소시켰으며, spurs를 억제할 수 있도록 설계되였다. 설계된 회로는 $0.18{\mu}m$ CMOS 공정 기술을 사용하여 CADENCE사의 specter로 시뮬레이션 하였으며, virtuso2로 레이아웃 하였다.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1257-1264
• /
• 2019

A 3-GSymbol/s/lane transceiver, which supports the mobile industry processor interface (MIPI) C-physical layer (PHY) specification version 1.1, is proposed. It performs channel mismatch correction to improve the signal integrity that is deteriorated by using three-level signals over three channels. The proposed channel mismatch correction is performed by detecting channel mismatches in the receiver and adjusting the delay times of the transmission data in the transmitter according to the detection result. The channel mismatch detection in the receiver is performed by comparing the phases of the received signals with respect to the pre-determined data pattern transmitted from the transmitter. The proposed MIPI C-PHY receiver is designed using a 65 nm complementary metal-oxide-semiconductor (CMOS) process with 1.2 V supply voltage. The area and power consumption of each transceiver lane are 0.136 ㎟ and 17.4 mW/GSymbol/s, respectively. The proposed channel mismatch correction reduces the time jitter of 88.6 ps caused by the channel mismatch to 34.9 ps.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.2
• /
• pp.22-27
• /
• 2009

In this paper, an automatic functional inspection system EVT (Emulated Vision Tester) for LCD drive module PCB has been proposed and implemented. Typical automatic inspection system such as probing methods and vision-based systems are widely known and used, however, there exist undetectable defects due to critical timing factors which they may miss to catch from LCD equipments. Especially typical vision-based systems have inconsistency on acquisition of images so that distinction between gray scales can be difficult which results in low level of performance and reliability on the inspection results. The proposed EVT system is pure hardware solution. It directly compares pattern signals from a pattern generator to output signals from LCD drive module. It also inspects variety of analog signals such as voltage, resistance, wave forms and so forth. The EVT system not only shows high performance in terms of reliability and processing speed but reduces costs on inspection and maintenance. Also, full automation of entire production line can be realized when EVT is applied in in-line inspection processes.

• Journal of Sensor Science and Technology
• /
• v.8 no.6
• /
• pp.427-433
• /
• 1999

In this paper, we have presented an one-axis fluxgate magnetic sensor with ferrite core, excitation, and pick-up coil. This magnetometer is consist of a sensing element, driving circuits for excitation coil and signal processing for detecting second harmonic frequency component which is proportional to the DC magnetic to be measured. The sensor core is excited by a square waveform of voltage through 82 turns of the excitation coil. The second harmonic output of pick-up coil(150 turns) is measured by a FFT spectrum analyzer. This result is compared to output of PSD(phase sensitive detector) unit for detecting a second harmonic component. The measured sensitivity is about 50 V/T at driving frequency of 2 kHz. The nonlinearity of fluxgate magnetic sensor is calculated about 2.0%.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.1
• /
• pp.80-87
• /
• 2012

We have developed the ATE(Automatic Test Equipment) system for the performance test of pre-amplifier of thermal imaging devices. The device regenerates the electronic signals of photon detection module which is normally in weak energy, for the image signals processing. Previous ATE system was primarily and actively developed in the field of semiconductor devices quality parts inspection. Recently, it has been studied in the field of performance testing of equipment. In the field of thermal performance test equipment, however, it lacks the study of ATE compared to other areas, which causes the maintenance related to the core of military thermal imaging system maintenance to be limited. In this paper, a new study of ATE in the field of thermal imaging system is done. It is designed to be used universally for the ATE system with different types of circuit card of thermal imaging system by adopting matrix relays. Using the developed ATE measuring the pre-amplifier amplitude, an average amplified amplitude of 2.71Vpp was measured which confirms that it is within the range of theoretical analysis and also verifies the good performance of the developed ATE.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.5
• /
• pp.359-369
• /
• 2020

In this paper, we proposed a charge pump (CP) circuit that has a wide operating range while reducing the current mismatch for the PLL that generates the main clock of the CMOS X-Ray detector. The operating range and current mismatch of the CP circuit are determined by the characteristics of the current source circuit for the CP circuit. The proposed CP circuit is implemented with a wide operating current mirror bias circuit to secure a wide operating range and a cascode structure with a large output resistance to reduce current mismatch. The proposed wide operating range cascode CP circuit was fabricated as a chip using a 350nm CMOS process, and current matching characteristics were measured using a source measurement unit. At this time, the power supply voltage was 3.3 V and the CP circuit current ICP = 100 ㎂. The operating range of the proposed CP circuit is △VO_Swing=2.7V, and the maximum current mismatch is 5.15 % and the maximum current deviation is 2.64 %. The proposed CP circuit has low current mismatch characteristics and can cope with a wide frequency range, so it can be applied to systems requiring various clock speed.