• Journal of Powder Materials
• /
• v.28 no.3
• /
• pp.221-226
• /
• 2021

We fabricate the non-equiatomic high-entropy alloy (NE-HEA) Fe_49.5Mn₃₀Co₁₀Cr₁₀C_0.5 (at.%) using spark plasma sintering under various sintering conditions. Each elemental pure powder is milled by high-energy ball milling to prepare NE-HEA powder. The microstructure and mechanical properties of the sintered samples are investigated using various methods. We use the X-ray diffraction (XRD) method to investigate the microstructural characteristics. Quantitative phase analysis is performed by direct comparison of the XRD results. A tensile test is used to compare the mechanical properties of small samples. Next, electron backscatter diffraction analysis is performed to analyze the phase fraction, and the results are compared to those of XRD analysis. By combining different sintering durations and temperature conditions, we attempt to identify suitable spark plasma sintering conditions that yield mechanical properties comparable with previously reported values. The samples sintered at 900 and 1000℃ with no holding time have a tensile strength of over 1000 MPa.

• Journal of Powder Materials
• /
• v.29 no.3
• /
• pp.219-225
• /
• 2022

An alternative fabrication method for carburizing steel using spark plasma sintering (SPS) is investigated. The sintered carburized sample, which exhibits surface modification effects such as carburizing, sintered Fe, and sintered Fe-0.8 wt.%C alloys, is fabricated using SPS. X-ray diffraction and micro Vickers tests are employed to confirm the phase and properties. Finite element analysis is performed to evaluate the change in hardness and analyze the carbon content and residual stress of the carburized sample. The change in the hardness of the carburized sample has the same tendency to predict hardness. The difference in hardness between the carburized sample and the predicted value is also discussed. The carburized sample exhibits a compressive residual stress at the surface. These results indicate that the carburized sample experiences a surface modification effect without carburization. Field emission scanning electron microscopy is employed to verify the change in phase. A novel fabrication method for altering the carburization is successfully proposed. We expect this fabrication method to solve the problems associated with carburization.

• Journal of Soil and Groundwater Environment
• /
• v.27 no.5
• /
• pp.10-17
• /
• 2022

Inorganic acids such as HCl, HNO₃, and H₂SO₄ have been commonly applied to soil washing of heavy metals-contaminated soil due to their cost-effectiveness. However, implementing the 'Chemical Substance Control Act' requires off-site risk assessment of the chemicals used in the soil washing. Therefore, in this study, organic acids or Fe(III)-based washing agents were evaluated to replace commonly used inorganic acids. Ferric removed heavy metals via H⁺ generated by hydrolysis, which is similar to the HCl used in the control group. Oxalic acid and citric acid were effective to remove Cu, Zn, and Cd from soil. Organic acids could not remove Pb because they could form Pb-organic acid complexes with low solubility. Furthermore, Pb could be adsorbed onto the iron-organic acid complex on the soil surface. Ferric could remove exchangeable-carbonate, Fe-Mn hydroxide, and organic matter and sulfides bound heavy metals (F1, F2, and F3). Organic acids could remove the exchangeable-carbonate and Fe-Mn hydroxide bound metals (F1&F2). Therefore, this research shows that the fractionation of heavy metals in the soil and the properties of washing agents should be considered in the selection of agents in the process design.

• Journal of Powder Materials
• /
• v.29 no.5
• /
• pp.399-410
• /
• 2022

Changes in the mechanical properties and microstructure of an IN 939 W alloy according to the sintering heating rate were evaluated. IN 939 W alloy samples were fabricated by spark plasma sintering. The phase fraction, number density, and mean radius of the IN 939 W alloy were calculated using a thermodynamic calculation. A universal testing machine and micro-Vickers hardness tester were employed to confirm the mechanical properties of the IN 939 W alloy. X-ray diffraction, optical microscopy, field-emission scanning electron microscopy, Cs-corrected-field emission transmission electron microscopy, and energy dispersive X-ray spectrometry were used to evaluate the microstructure of the alloy. The rapid sintering heating rate resulted in a slightly dispersed γ' phase and chromium oxide. It also suppressed the precipitation of the η phase. These helped to reinforce the mechanical properties.

• Journal of East-West Nursing Research
• /
• v.16 no.1
• /
• pp.70-75
• /
• 2010

Purpose: Nursing students face constant threats of blood-borne infections such as HIV, Hepatitis B, and Hepatitis C during their clinical rotation period. This study was done to determine the frequency and risk of the exposure to blood and body fluids. Methods: The data was collected using a questionnaire. Ninety eight junior & senior nursing students were participated in this study. Results: 75.6% of the participants reported more than once during practicum. The exposure occurred most frequently while checking the blood glucose (65.3%). The general ward (45.3%) was the most frequent site for the occurrence of the exposure. However, only eight cases (10.7%) were reported to the medical or nursing personnel in charge. Conclusions: This study shows nursing students are in a great risk of the exposure to blood & body fluid. The risk is highest in the general ward during checking the blood glucose. Thorough education on preventive measures, should be provided to nursing students prior to clinical practium.

• Journal of East-West Nursing Research
• /
• v.29 no.1
• /
• pp.68-77
• /
• 2023

Purpose: The purposes of this study were to develop a predictive model and evaluate this model of turnover in hospital nurses. Methods: Participants were 1,565 nurses from a tertiary hospital in South Korea. Descriptive statistics and a decision-tree analysis were performed using the SPSS WIN 23.0 program. Results: The turnover groups were presented in eleven different pathways by decision tree analysis. There were three high-risk groups with a higher turnover rate than the average, and eight low-risk groups with a lower turnover rate. Among them, two low-risk groups had a 0% turnover rate. The groups were classified according to general characteristics such as position, period of temporary position, clinical career at last working unit, total clinical career, and period of leave of absence. The accuracy of the model was 83.2%, sensitivity 63.7%, and specificity 98.1%. Conclusion: This predictive model of turnover may be used to screen the turnover risk groups and contribute for decreasing the turnover of hospital nurses in South Korea.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.1
• /
• pp.7-14
• /
• 2023

We investigated the effect of multiple tempering on the microstructure and mechanical properties of AISI 4340 steel. The austenitized and quenched AISI 4340 steels were tempered at 550, 600, and 650℃ for 1, 2, and 4 h by single-tempering (ST). The multiple tempering was conducted for 4 h by double-tempering (DT, 2 h + 2 h), and quadruple-tempering (QT, 1 h + 1 h + 1 h + 1 h). As tempering temperature increases, yield strength and ultimate tensile strength decrease and elongation increases due to recovery and recrystallization of martensite and coarsening of carbides. At 550℃, as the number of tempering cycles increases, the yield strength and tensile strength decrease at the expense of fracture elongation. At 600 and 650℃, the yield strength and tensile strength increase with increasing the number of tempering cycles while fracture elongation maintains similar values. The multiple tempering at the same tempering time of 4 h improves the modulus of toughness at all tempering temperatures, which is presumed to be due to the change in carbide precipitation behavior by multiple tempering.

• Journal of the Korean Society of Food Culture
• /
• v.23 no.5
• /
• pp.616-620
• /
• 2008

The principal objective of this study was to evaluate the quality characteristics of Bokbunja pudding, using various levels of Bokbunja fruit juice (140, 150, and 130 g), Bokbunja Wine (10, 20, and 20 g), gelatin (18, 17, and 16 g) and sugar (250, 200, and 150 g). In order to establish the optimal added amounts, chemical composition, saccharinity, color, texture, and sensory evaluations were conducted, and the results of various cases were analyzed and assessed. The statistical data analyses were conducted using the SPSS program. The saccharinity of the Bokbunja pudding increased with increasing amountsof added sugar. Additionally, as the amount of added Gelatin was increased, the L values (lightness) of the Bokbunja pudding decreased. Conversely, the hardness, gumminess, and chewiness values all decreased with decreasing levels of added gelatin and sugar. The optimal mixing condition for the Bokbunja pudding was determined via sensory evaluation. Sensory characteristics, including flavor, sweetness, texture, and overall acceptability, were highest in the type C product. The chemical composition of the type C product was as follows: moisture 71.47%, carbohydrate 24.70%, crude protein 3.83%, crude fat 0.001%, and crude ash 0.001%. According to our results, the optimum mixing ratio for the most satisfactory sensory characteristics of Bokbunja was as follows: Bokbunja fruit juice 130 g, Bokbunja Wine 20 g, Gelatin 16 g, Sugar 150 g, Bokbunja Flavor 0.3 g, and Water 400 g.

• Journal of Powder Materials
• /
• v.30 no.6
• /
• pp.470-477
• /
• 2023

The effects of annealing on the microstructure and mechanical properties of Al-Zn-Mg-Cu-Si alloys fabricated by high-energy ball milling (HEBM) and spark plasma sintering (SPS) were investigated. The HEBM-free sintered alloy primarily contained Mg₂Si, Q-AlCuMgSi, and Si phases. Meanwhile, the HEBM-sintered alloy contains Mg-free Si and θ-Al₂Cu phases due to the formation of MgO, which causes Mg depletion in the Al matrix. Annealing without and with HEBM at 500℃ causes partial dissolution and coarsening of the Q-AlCuMgSi and Mg₂Si phases in the alloy and dissolution of the θ-Al₂Cu phase in the alloy, respectively. In both alloys, a thermally stable α-AlFeSi phase was formed after long-term heat treatment. The grain size of the sintered alloys with and without HEBM increased from 0.5 to 1.0 ㎛ and from 2.9 to 6.3 ㎛, respectively. The hardness of the sintered alloy increases after annealing for 1 h but decreases significantly after 24 h of annealing. Extending the annealing time to 168 h improved the hardness of the alloy without HEBM but had little effect on the alloy with HEBM. The relationship between the microstructural factors and the hardness of the sintered and annealed alloys is discussed.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.46 no.spc
• /
• pp.31-38
• /
• 2023

In this study, in order to develop a method to efficiently inject essential nutrients necessary for plant growth into wood chips, which are simply used as soil covering materials in the agriculture, landscaping and horticultural industries, the atmospheric pressure dipping method and the vacuum pressure impregnating method are used to improve the plant nutrients injectability and impregnation amount were comparatively analyzed. Nutrient ingredients and 8 major heavy metal contents of wood chips injected with nutrients were analyzed, and soil covering effects were examined by covering wood chips injected with nutrients on soil. Comparing the dipping method and the vacuum pressure impregnation method, it took about 48 hours or more to inject 1,500 g or more of the nutrient aqueous solution into 1 kg of wood chips in the dipping method, but the vacuum pressure impregnation method could be impregnated in about 5 minutes. Components of the impregnated nutrients were detected in proportion to the diluted concentration. As a result of covering the wood chips developed in this study on soil, they showed weakly acidic pH, and the heat insulation and moisturizing effects during the winter season were evaluated to be superior to those of uncovered soil. In the future, wood chips impregnated with nutrients are expected to contribute to the more efficient use of waste wood resources and the long-term supply of nutrients essential for plant growth, reducing excessive use of chemical fertilizers and reducing costs.