• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.11
• /
• pp.1025-1030
• /
• 2016

The big problem of accidents at sea is negligent watch, it causes collision, fender bender, stranding, rollover, and sinking of fishing vessel. Most accidents happens without an eyewitness, it is difficult to identify the cause of the accident. VDR(: Voyage Data Recorder) is needed to identify a cause of the accident, the VDR is not usually used for fishing vessel because of high cost. Thus, this paper designs and develops a VDR system for fishing vessel. If the system is used, cause of a sea accident can be quickly identified. Also, a VDR system can be used for appropriate measures to fix a cause of the accident. Finally, it also can be helpful to prevent maritime accidents.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.5
• /
• pp.497-503
• /
• 2018

Passenger ships and training ships have a common feature in that they serve many passengers. Thus, safe navigation is very important. During normal sailing, a ship may turn using various types of steering, including maneuvers to avoid collisions with dangerous target. When a ship turns, a heeling angle occurs. If trouble arises during sailing, a dangerous heeling angle may result or a capsizing accident. In this study, the heeling angle during turning was measured through experimentation with two training ships similar to passenger ships. These findings were compared with theoretical formulas for heeling angle when turning. We confirmed that the limit of the maximum heeling angle estimation using heeling angle formula when turning presented in IMO stability criteria. In addition, it was confirmed that the maximum estimated heeling angle can be reached by applying the result calculated in the theoretical formula 1.4 times when turning right and 1.1 times when turning left to reflect sailing speed when of rudder hard over. It is expected that this study will provide basis data for establishing safe operation standards for the prevention of dangerous heeling angles when turning.

• Journal of Navigation and Port Research
• /
• v.41 no.6
• /
• pp.365-372
• /
• 2017

The rolling motion of a floating body makes crews and passengers exhausted and/or applies forces to the structure to cause damage; it might even upset the body. Therefore, almost all ships are equipped with bilge keels for anti-rolling; in special cases, an anti-rolling tank(ART) or fin stabilizer or gyroscope could be installed. But an ART requires a large capacity to install it, and a fin stabilizer and gyroscope need great costs to install and also many expenses to operate. The authors suggest the use of an anti-rolling pendulum(ARP), and they showed that the ARP is effective to reduce rolling by experiments and via a Runge-Kutta analysis. This paper introduces the linearized 2 degrees of freedom with a viscous damping system for a ship equipped with ARP; it also shows the validation of the linearized analysis for the ship's roll motion. The paper proposes an optimum ARP on the basis of the justified model. The case of the 7.7kg model with ship 20g ARP of a mass ratio of 0.26%, is the most effective for reducing roll motion. The paper shows the ARPs with various mass ratios are effective for reducing the roll motion of a ship by free decaying roll experiments.

• Journal of Navigation and Port Research
• /
• v.41 no.6
• /
• pp.451-466
• /
• 2017

Deep-sea fishing vessel No. 501 Oryong was fully flooded through its openings and sunk to the bottom of the sea due to the very rough sea weather on the way of evasion after a fishing operation in the Bearing Sea. As a result, many crew members died and/or were missing. In this study, a full-scale ship flooding sinking simulation was conducted, and the sinking process was analyzed for the precise and scientific investigation of the sinking accident using highly advanced Modeling & Simulation (M&S) system of Fluid-Structure Interaction (FSI) analysis technique. To objectively secure the weather and sea states during the sinking accident in the Bering Sea, time-based wind and wave simulation at the region of the sinking accident was carried out and analyzed, and the weather and sea states were realized by simulating the irregular strong wave and wind spectrums. Simulation scenarios were developed and full-scale ship and fluid (air & seawater) modeling was performed for the flooding sinking simulation, by investigating the hull form, structural arrangement & weight distribution, and exterior inflow openings and interior flooding paths through its drawings, and by estimating the main tank capacities and their loading status. It was confirmed that the flooding and sinking accident was slightly different from a general capsize and sinking accident according to the simple loss of stability.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.7
• /
• pp.863-870
• /
• 2023

Ship capsize accidents are common in coastal waters, particularly involving small fishing boats. To prevent there overturing accidents in small fishing boats, their stabilities must be assessed at the initial design step. However, the available information during the initial design step is limited, posing challenges in performing a reliable stability evaluation. Therefore, this study presents a plan to estimate the transverse metacenter (GM) of small fishing boats using parameters such as KM, KG, and TRIM that can be determined at the initial design step. Stability was evaluated by comparing GM with the minimum transverse metacenter (GMmin) specified in the standard safety evaluation criteria for fishing boats. To calculate the required trim value for hydrostatic characteristics using K-SHIP, a stability assessment program provided by the Korea Maritime Safety and Transportation Corporation, the initial trim state is estimated based on the ship lines using the commercial CFD program STAR-CCM+. GM is then calculated by assessing the hydrostatic characteristics in relation to the boat lines using K-SHIP. Furthermore, the stability of the fully loaded state is compared by subtrcating GM from GMmin. One constructed ship is designated as the standard ship, and the stability assessment method proposed in this study is applied to evaluate stability and validate its effectiveness. Consequently, the representative line of a 4.99-ton fishing boat and nine modular lines models derived from it were evaluated, ultimately identifying a relatively superior stability.

• Journal of Navigation and Port Research
• /
• v.40 no.6
• /
• pp.361-368
• /
• 2016

A ship's rolling motion can make crew and passengers sick and/or apply forces to the structure that cause damage.. Therefore bilge keels are equipped in most ships for anti-rolling. In special cases, anti-rolling tanks (ARTs), fin stabilizers, or gyroscopes can be installed. However, ARTs require a large area to install, and fin stabilizers and gyroscopes are costly to install and expensive to operate. This paper suggests a Anti-rolling pendulum (ARP) to reduce roll motion. ARPs acts like ARTs. However, the ARP has a circular shaped guidance arc instead of the string or wire of a simple pendulum. The device suggested has about 1/ 8 the weight and 1/ 6 the volume of a ART and is more effective. This study derives the nonlinear and linear differential equations of system motion.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.4
• /
• pp.1-11
• /
• 1997

When a barge is towed by a tug boat using a tow line, the barge is frequently subject to a large sway motion induced from its inherent yaw motions. This large sway motion combined with external forces due to winds and waves may makes the towing to be difficult or even dangerous. It has been reported that in worse situations, barges or tugs are capsized. In addition, the large sway motion of the towed barge gives a menace to the safety of ships navigating nearby. This paper is the results of the experimental investigation into the course stability of an 8,000 DWT barge using a Towing Tank and a Circulating Water Channel. Various skegs are designed and course stability tests for the barge with skegs are conducted in calm water and in irregular waves. It is observed that an effective skeg attached to the barge enables the sway motion to be zero while the sway amplitude of the bare hull is around 10 times its breadth.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.30 no.1
• /
• pp.127-134
• /
• 2024

With the growth of offshore wind power generation market, the corresponding installation vessel market is also growing. It is anticipated that approximately 100 installation vessels will be required in the of shore wind power generation market by 2030. With a price range of 300 to 400 billion Korean won per vessel, this represents a high-value market compared to merchant vessels. Particularly, the demand for large installation vessels with a capacity of 11 MW or more is increasing. The rapid growth of the offshore wind power generation market in the Asia-Pacific region, centered around China, has led to several discussions on orders for operational installation vessels in this region. The seabed geology in the Asia-Pacific region is dominated by clay layers with low bearing capacity. Owing to these characteristics, during vessel operations, significant spudcan and leg penetration depths occur as the installation vessel rises and descends above the water surface. In this study, using penetration variables ranging from 3 to 21 m, the unique vibration period, structural safety of the legs, and conductivity safety index were assessed based on penetration depths. As the penetration depth increases, the natural vibration period and the moment length of the leg become shorter, increasing the margin of structural strength. It is safe against overturning moment at all angles of incidence, and the maximum value occurs at 270 degrees. The conditions reviewed through this study can be used as crucial data to determine the operation of the legs according to the penetration depth when developing operating procedures for WTIV in soft soil. In conclusion, accurately determining the safety of the leg structure according to the penetration depth is directly related to the safety of the WTIV.

• Journal of Navigation and Port Research
• /
• v.46 no.1
• /
• pp.18-25
• /
• 2022

MOF strengthen the law and institutions for safety management after the capsize accident of passenger ship "Sewol" on April 16, 2014. Nevertheless, about 13 cases of marine accidents such as collisions, contact, and stranding have occurred in coastal passenger ships over the past 5 years. Particularly, according to the judgment of KMST, most of the main causes of passenger ship accidents occurred within harbor areas because of the master's improper ship-handling or inattention. And so, this study analyzed four cases of marine accidents on passenger ships that occurred in the port areas and examined the environmental, institutional, material, and human factors that contributed to the master's improper ship-handling and behavior, and the results are as follows. First, as an environmental factor, the size of the turning basin was not enough. Second, as an institutional factor, the VTS control was not properly supported, the master lacked sufficient training for safe ship-handling in the port area and up-to-date charts were not provided. Third, as a material factor, the digital type speed log capable of the ship's speed in real-time was not installed on the ship's wing bridge. Lastly, as a human factor, the master could not take proper bridge resources and the passage plan was not proper. Therefore, it is suggested in this paper that the size of the turning basin should be adjusted to meet the prescribed standards, the master of passenger ships should receive the ship-handling simulation training among other safety training to ensure safe ship-handling of the master in the port area as improvement measures.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.1
• /
• pp.1-7
• /
• 2013

Structural design and analysis of a coiling arm unloading machine for submarine cable have been originally conducted in this study. Three-dimensional CAD modeling process is practically applied for the structural design in detail. Finite element method(FEM) and multi-body dynamics(MBD) analyses are also used to verify the safety and required motions of the designed coiling arm structure. The effective moving functions of the designed coiling arm with respect to rotational and radial motions are achieved by adopting bearing-roller mechanical parts and hydraulic system. Critical design loading conditions due to its self weight, carrying cables, offshore wind, and hydraulic system over operation conditions are considered for the present structural analyses. In addition, possible inclined ground conditions for the installation of the designed coiling arm are also considered to verify overturn stability. The present hydraulic type coiling arm system is originally designed and developed in this study. The developed coiling arm has been installed at a harbor, successfully tested its operational functions, and finished practical unloading mission of the submarine cable.