• Journal of Advanced Navigation Technology
• /
• v.5 no.2
• /
• pp.165-174
• /
• 2001

In this paper, we investigated performance for 5.8 GHz dedicated short range communication system using OFDM which will be applied to Intelligent transportation system services. We analyzed modulation technique and interference cancellation method to improve performance in physical layer. We presented channel model to estimate performance between Roadside Unit and Onboard Unit. finally, We calculated the link budget of entire system which analyzed performance of channel according to transmission power, presented the adaptive modulation using pilot signal and RSSI algorithm is proposed.

• Journal of Astronomy and Space Sciences
• /
• v.19 no.4
• /
• pp.273-282
• /
• 2002

We describe some performance of the detector electronics system for the FIMS (Far-ultraviolet Imaging Spectrograph) mission. The FIMS mission to map the far ultraviolet sky uses MCP (micro-channel plate) detectors with a crossed delay line anode to record photon arrival events. FIMS has two MCP detectors, each with a ~25mm$\times$25mm active area. The unconventional anode design allows for the use of a single set of position encoding electronics for both detector fields. The centroid position of the charge cloud, generated by the photon-stimulated MCP, is determined by measuring the arrival times at both ends of the anode following amplification and external delay. The temporal response of the detector electronics system determines the readout's positional resolution for the charge centroid. High temporal resolution (<$35{\times}75$ps FWHM) and low power consumption (< 6W) were achieved for the FIMS detector electronics system.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.6 s.360
• /
• pp.24-30
• /
• 2007

In this paper, an energy detection-based low power, low complexity IR-UWB receiver in multipath impulse radio channel is presented. The proposed receiver has a simple 1-bit sampler for energy detection. Also, multipath signal received from multipath impulse radio channel is amplified and envelope of the signal is detected. Then, energy detection technique using integrator by summing multipath signals in certain period is adopted to minimize the BER loss by simple energy detection. In particular, in acquisition of a sample signal, SNR is additionally improved using a digital sampler. Symbol decision using several sampled signals is performed and thus the process of symbol synchronization is significantly simplified. Also, it is effectively designed to be compatible with influences of multipath and timing error. In addition, the proposed receiver complexity is reduced using pulse decision window. The performance of the proposed receiver is simulated based on IEEE 802.15.4a channel model and the algorithms are implemented on FPGA.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.9
• /
• pp.46-53
• /
• 2014

In this paper, ku-band RF transceiver system is designed for the unmanned aerial vehicle(UAV) line-of-sight(LOS) datalink. The RF transceiver system is consisted of the transmitting and receiving unit, RF front-end unit, and high power amplification unit. The transmitting and receiving unit has the functions of frequency up/down converting and channel changing. The RF front-end unit has the functions of transmitting and receiving signal duplexing, antenna selection, small signal amplification, and frequency filtering excluding the receiving signal. The high power amplification unit has the functions of ku-band power amplification and transmitting power variation(High/Middle/Low/Mute). The frequency up/down converting of transmitting and receiving unit is designed by using the superheterodyne method. The RF transceiver system is designed to obtain the broadband and high linearity properties for the reliable transmission and reception of high data-rate and high speed data. Also, the channel changing function is designed to use selectively the frequency as the operation environment of UAV.

• Journal of Satellite, Information and Communications
• /
• v.9 no.1
• /
• pp.74-78
• /
• 2014

In this paper, we proposed Interference suppression method of between AMI system and EV charging system. IEC12139-1 and HomePlug GreenPhy are using 2-30Mhz frequency band in power line communication. Both method while using the same frequency band, interference occurs in the system of each other. In this paper, we experiment a way to suppress the interference through the channel separation using a Walsh code.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.3
• /
• pp.368-377
• /
• 1999

In this paper, the wide-band CDMA transmitter for 2 GHz band is designed and implemented. The CC-OQPSK implemented as ASIC has better spectral and power efficiency than the conventional QPSK system because it has constant envelope characteristics. Good harmonics rejection characteristics and gain of 20 dB are shown on the intermediate frequency stage using double-conversion scheme. The output power of two-stage RF amplifier is +2l.14 dBm in 1.9 GHz band. It is confirmed that the electrical characteristics of the transmitter satisfy with required the specification of the wide-band CDMA transmitter for 2 GHz band.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.52 no.12
• /
• pp.696-701
• /
• 2003

This paper presents a systematic method of probing channel characteristics and communication reliabilities of home power line communication network applied to the Internet accessed control of home appliances. The effects of the three performance deterioating factors, i.e., additive noise, channel attenuation, and intersymbol interference, can be systematically measured by applying the channel probing waveform in the frequency range from 100KHz to 450KHz. Probability of bit error is derived with the probed channel parameters of the signal attenuation, noise and signal-to-interference ratio read in the frequency domain. The agreement between the derived probability of bit error and the measured probability of bit error supports the validity of the proposed approach of probing home power line channel characteristics. The experimental results performed with the constructed test-bed applying the proposed channel probing method also support the feasibility of commercially deploying the PLC modem installed home appliances and their services for the Internet accessed home automation.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.52 no.2
• /
• pp.107-111
• /
• 2003

In the power-line communication systems, there are many factors of noise and attenuation in the power-line channels, because they were designed for not the communication but the power transmission. Also the transfer function of the channels is highly changed with the topology and the load of the power-lines. To cope with these poor channel situation, channel modeling, one of the many studies in progress, is being studied hard. Channel modeling is essential to apply the active schemes to overcome the bad channel(e.g. modulation technique, channel coding, signal coupling & filtering, etc.) to the power-line communications. In this paper, we have realized the statistical model(this model is suggested as the channel modeling method for the power-line channels) that is combined the transfer function with the various noises. And we have compared and examined the results with the measured data. Also we have studied the plan which can effectively establish the channel data base for the channel information consisted of the parameters that are derived from this modeling, and we have studied the plan to utilize the data base.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.5
• /
• pp.175-180
• /
• 2019

The optical characteristics and power transfers between guiding channels of blazed grating-assisted directional coupler (B-GADC) are evaluated in detail by using novel and rigorous modal transmission-line theory (MTLT) based on eigenvalue problem. To evaluate the coupling efficiency of B-GADC, the dispersion curves as a function of the grating period and wavelength are analyzed numerically for quasi-TE and quasi-TM modes. Furthermore, symmetric, sawtooth and asymmetric grating profiles are considered to know the effect of blazing characteristics on power transfer of GADC. The numerical results show that the grating period for minimum-gap condition to obtain maximum power transfer decreases gradually as the blazed structure changes from symmetric to asymmetric profile. On the other hand, the coupling length increases reversely.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2640-2642
• /
• 2002

In this paper, we show the channel characteristics measurement system the frequency range up to 30MHz for medium voltage Power Line Grid. Power line channel characteristics are investigated by means of various measurement instruments. Measurement system consists of medium voltage coupler, impedance measurement part, noise measurement part, voltage sensing part and communication part. Measured data will be used for PLC channel modeling and PLC network system design.