• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.6 no.2
• /
• pp.56-61
• /
• 1992

This paper is reported on the simulation and test results of a constant flux vector control scheme of an induction motor without any speed detecting eqiupment, in which the adaptive current PWM inverter is used. The rotor speed is estimated form stator voltage, current and parameters of motor, and control algorithm in the system is performed with by micro processor. By comparing the waveform of input current of this system with that of the case with taco-generator, good agreement is observed except small ripple component. Experimental results which are acquired at start up and during acceleration/deceleration are quite similar to those of the simulation results.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.30-32
• /
• 2003

본 논문은 LCD 제조 공정 라인에서 LCD용 원판을 다른 여러 공정으로 이송하는데 사용하기 위한 수평형 스토크 시스템의 설계 및 제작에 관한 연구이다. 구동원으로 제작된 영구 자석 여자 횡자속형 전동기는 높은 공극 자속 밀도를 얻을 수 있는 구조로 일반 선형 유도 전동기나 선형 등기기에 비해 단위 체적당 높은 출력 밀도를 얻을 수 있는 장점을 가지고 있다. 3차원 등가 자기 회로망법을 사용하여 기자력 변화에 따른 추력 및 흡인력과 같은 특성을 해석하였으며 정특성 실험을 통하여 설계 및 해석의 타당성을 검토하였다.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.963-965
• /
• 2005

본 연구는 대용량 추진용 32극, 192슬롯의 3MW급의 BLDC(Brushless DC) 전동기를 모델로 2차인 유한요소법(FEM)을 이용 전자계 및 열계 특성을 해석한 것이다. 이러한 해석을 통하여 BLDC 전통기의 진동 및 소음의 원인을 분석하고 성능향상을 위한 방법을 연구하며 이에 전동기의 소음 및 진동의 저감과 성능을 향상시킬 수 있는 최적설계에 그 목적이 있다. 또한 FEM을 이용 열계 특성을 해석하고 이를 분석하여 설계정수 변경에 반영한다. 위의 결과들을 설계에 적용하여 BLDC의 성능향상을 위한 최적설계 모델을 제시하게 될 것이다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.1
• /
• pp.49-56
• /
• 2001

This paper presents a new approach to the problem based on neural network methods. Instead of using general controllers, neural networks PID control are used to control AC servo motor. The most popular and widely used control method in servo system control loops is PID type. PID controller has the features of simple structure, stability and reliability. But it has limitations in complex system control and can not remain above virtues under the conditions of parameters uncertain and environment uncertainties. AC servo motor controller is designed for drive of the cartesian coordinate type for machine tools.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.4
• /
• pp.812-818
• /
• 2003

This paper presents a developed outside rotor type induction motor for the fan. Nearly all of the induction motors consist of two parts, rotor and stator, and the position of rotor is generally inside of stator. However, the rotor of the developed induction motor is located outside of stator. It is believed that the outside rotor type induction motor is suitable for the fan due to its large inertia, that is, it is considered that the change of air flow rate resulting from input power or load fluctuation is reduced. In this paper, the two tests which are suitable to obtain the electrical parameters of the outside rotor type induction motor were described, then various parameters of outside rotor type induction motor were measured. These are the locked rotor test and no load test. By using these tests, it was possible to determine the parameters which are presented in the steady-state equivalent-circuit of the outside rotor type induction motor. Load test of induction motor was carried out using a dynamometer and the torque-speed curve was obtained. It is believed that the results of this paper can be used for the development of the outside rotor type induction motor.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.3
• /
• pp.66-74
• /
• 2005

This paper presents an implementation of digital servo speed control system of SPMSM(Surface-mounted Permanent Magnet Synchronous Motor) for industrial application with Direct Torque Control(DTC) using TMS320F2812 DSP. Although, the vector control scheme is adapted in many industrial servo system, but the DSP calculation ratio is increased by reference frame transformation and SVPWM of vector control. Therefore, this paper investigate the possibility of DTC scheme for industrial servo drive system instead of vector control scheme. DSP calculation ratio is compared between vector control and DTC algorithm in addition to the characteristic of speed control response. The suggested SPMSM control system shows the possibility of DTC scheme for industrial servo motor drive system instead of a vector control algorithm.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.9 no.1
• /
• pp.37-46
• /
• 1995

Along with the recent trend of complexity and long distance transmission in power system, dynamic analysis of stability considering the load characteristics is an important subject. In this paper, the influence of the induction motor loads on the power system voltage is investigated. The influence of the inductive load ratio and the inertia of induction motor on the voltage response of the power system are examined, and in the case of the high percentage of the induction motor load, induction motors in the power system can lead to transient voltage instability even under the system condition such as switching operation. The application of static condenser(SC) to prevent the transient voltage instability is introduced.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.812_813
• /
• 2009

본 논문에서 로프리스 엘리베이터용 영구자석형(PM) 선형동기전동기(LSM)의 디텐트력을 저감하기 위하여 반응표면법(RSM)을 이용한 디텐트력의 최소화 설계 방법을 제안하였다. RSM을 이용하여 정수 슬롯형과 분수 슬롯형 PM-LSM의 설계변수를 추론하고 유한요소법(FEM)으로 디텐트력을 구하였다. 반응표면법과 유한요소법의 해석결과를 토대로 분수 슬롯형 PM-LSM이 주어진 체적의 엘리베이터 시스템에 적합한 형상임을 입증한다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.497-504
• /
• 2000

This paper presents a method for the equivalent-circuit parameters and torque characteristics calculation of squirrel-cage induction motors. The measurment of motor parameters were calculated by the stator resistance test, the blocked rotor test and no load test through T type equivalent-circuit method. Especially, this paper describes the test results obtained by using hall sensor and strain gage for the current and the torque characteristics of induction motors. 1(HP), three-phase squirrel cage induction motor has been used during the test and the parameters are compared with those obtained by the maker parameters of simulation results and experiment.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.139-141
• /
• 1993

A new scheme to measure the rotor time constant and to set the slip gain of a vector-controller is presented. The approach utilizes the phase difference between the torque producing component of the stator current and rotor current in the stationary frame. It is shown that the rotor time constant can be uniquely identified by detecting the corresponding phase difference. The simulation was carried out by considering the variation of other parameters and the torque producing component of the stator current frequency.