• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.1
• /
• pp.276-284
• /
• 2013

This paper considers the transfer alignment in the inertial navigation system and the observability analysis is performed for velocity matching. The state variable of the Kalman filter is modeled including the lever arm error and the measurement equation is obtained. The SOM(Stripped Observability Matrix) method is used for the observability analysis for various maneuvering conditions of the vehicle, which gives the full state observability condition as a specific maneuver sequence of the vehicle. While the observability analysis of a lever arm effect in the existing papers is mainly performed by simulations, we performed it analytically by the observability analysis method. The analysis result is verified using the computer simulations.

• Water for future
• /
• v.27 no.4
• /
• pp.95-104
• /
• 1994

The sinuosity model has been developed to simulate to developed to simulate the floodwave in meandering channels by solving the extended Saint-Venant equation with the Preissmann scheme. The suggested model is compared with three conventional floodplain routing methods in terms of governing equations, mass conservation error and floodwave analysis. The sinuosity model produces the mass conservation error of 1.5-1.8%, however the separate channel model produces 9.1% and 27.4% for sinuosity of 1.5 and 2.0, respectively. The model has been used to simulate flow in an idealized meandering river with a floodplain. The attenuation ratio and the travel time ratio are found to increase as the floodplain roughness and width increase and as the sinuosity factor decreases. The model is expected to contribute the floodwave analysis in sinuous channel with compound corss sections.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.18 no.2
• /
• pp.1-13
• /
• 1981

Simple models for analyzing noise factors have been derived for four fundamental types of feedback amplifiers. These models have been obtained by changing equivalent noise sources of feedback networks into equivalent input noise sources of basic amplifiers. They are used to analyse noise factors for these amplifiers. Noise tractors measured for the four types of feedback amplifiers agree with theoretical results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.8
• /
• pp.1043-1049
• /
• 2012

In order to develop the decelerator for briquetting machine which composed of multi-staged gears, shafts and bearings, static design of the decelerator has been carried out through the analysis of bending and face forces, including structural analysis, applied on those teeth in accordance with AGMA(American Gear Manufacturers Association) standard. And also, dynamic design has been carried out with considering of vibratory forces caused by unbalance mass and transmitting error of gear. On the results of vibration analysis, it has been confirmed that there is not any critical speed within its operating range.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.12
• /
• pp.99-108
• /
• 1999

A four-degree-of-freedom non-linear model with time varying mesh stiffness has been developed for the dynamic analysis of spur gear trains. The model includes a spur gear pair, two shafts, two inertias representing load and prime mover. In the model, developed several factors such as time varying mesh stiffness and damping, separation of teeth, teeth collision, various gear errors and profile modifications have been considered. Two computer programs are developed to calculate stiffness of a gear pair and transmission error and the dynamic analysis of modeled system using time integration method. Dynamic tooth and mesh forces, dynamic factors are calculated. Numerical examples have been given, which shows the time varying mesh stiffness ha a significant effect upon the dynamic tooth force and torsional vibrations.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.5
• /
• pp.64-71
• /
• 2002

A new model utilizing a transfer function was proposed in the previous paper fur analizing motion errors of hydrostatic tables. Validity of the proposed method was theoretically verified as the calculated motion errors were compared with the results by conventional multi pad method. In this paper, relationship between form error of rail and motion errors of hydrostatic table is analized theoretically in order to comprehand so-called ‘averaging effect of oil film’. Experiments on the motion errors of hydrostatic table is conducted with 3 different rails, and the results are compared with the results calculated by Transfer Function Method. The results show good agreement. From the results, it is verified that TFM is very effective to analize the motion errors of hydrostatic table.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3246-3252
• /
• 1994

The vibration of meshing gear system is originated form teeth deformation, teeth contact ratio, profile error, etc. The gear vibration is classified as whine vibration during meshing and as rattle vibration during idling. In this study, the whine vibration is investigated under the assumption of piecewise linearity of elastic stiffness due to the variation of meshing. Numerical, theoretical and experimental investigations show the existence of the superharmonic components of the second and the third order. consistently It can be concluded that the superharmonic components in whine vibration of meshing gear is originated from the stiffness variation. It also shows that the higher order harmonics are reduced on the increase of motor speed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.454-458
• /
• 2001

A new model utilizing a transfer function was proposed in the previous paper for analizing motion errors of hydrostatic tables. Validity of the proposed method was theoretically verified as the calculated motion errors were compared with the results by conventional multi pad method. In this paper, relationship between form error of rail and motion errors of hydrostatic table is analized theoretically in order to comprehand so-called 'averaging effect of oil film'. Experiments on the motion errors of hydrostatic table is conducted with 3 different rails, and the results are compared with the results calculated by Transfer Function Method. The results show good agreement. From the results, it is verified that TFM is very effective to analize the motion errors of hydrostatic table.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.7
• /
• pp.185-194
• /
• 2004

In order to analyze the motion errors of the aerostatic stage, it is necessary to consider the influence of the moment variation occurred inside the pads. In this paper, a motion error analysis method utilizing the transfer functions on the reaction force and moment is proposed, and general characteristics of the transfer functions are discussed. Calculated motion errors by the proposed method show good agreement with the ones calculated by Multi fad Method, which is considered the entire table as an analysis object. Also, by the introduction of the transfer function of motion errors, which represent the relationship between the spatial frequency components of the rail form error and motion errors, motional characteristics of the porous aerostatic stage can be generalized. In detail, the influence of the spatial frequencies is analyzed qualitatively, and the patterns of the insensitive frequencies which almost do not affect the linear motion error or angular motion error according to the rail length ratio and the number of the pad are verified. The relationship between the moment variation occurred inside the pads and the motion errors is also verified together.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2009.04a
• /
• pp.365-371
• /
• 2009

산불에 있어 화염높이 산정은 복사열전달에 의한 수평 또는 수직적 화염확산을 예측하는데 있어 매우 중요한 부분이다. 화염특성 중 화염높이는 빛을 수반하는 화염(the luminous flame)의 평균높이로 확인할 수 있다. 본 연구에서는 외부 풍속과 경사 등으로 인한 화염 높이가 변화될 수 있는 조건을 제외한 산림 내 지표연소물질인 낙엽층(fuel bed)에 대한 화염높이 관측실험과 Cone calorimeter(ASTM-1354)을 이용하여Heat Release Rate 측정하였고 surface fuel에 대한 화염높이 산출식 $H_f=0.027{\dot{Q}}^{2/3}$을 도출하였다. 실험값과 개발 산정식, 기존 Heskestad(1998) 식과의 적용값 비교 결과, 소나무 낙엽의 경우, 실험값과 개발 산정식 적용값의 표준오차는 0.08, 실험값과 기존 Heskestad(1998)의 표준오차는 0.23으로 개발 산정식의 정확성이 높은 것으로 나타났다. 따라서 앞으로 이 식을 이용하여 복사열전달에 의한 화염확산해석 및 화염의 높이에 따른 수관화 전이해석 등에 활용 가능할 것으로 사료된다.