• Journal of Korean Society of Water and Wastewater
• /
• v.33 no.2
• /
• pp.111-119
• /
• 2019

Electro-coagulation process has been gained an attention recently because it could overcome the membrane fouling problems in MBR(Membrane bio-reactor). Effect of the key operational parameters in electro-coagulation, current density(${\rho}_i$) and contact time(t) on membrane fouling reduction was investigated in this study. A kinetic model for ${\rho}_i$ and t required to reduce the membrane fouling was suggested under different MLSS(mixed liquor suspended solids) concentration. Total 48 batch type experiments of electro-coagulations under different sets of current densities(2.5, 6, 12 and $24A/m^2$), contact times(0, 2, 6 and 12 hr) and MLSS concentration(4500, 6500 and 8500mg/L) were carried out. After each electro-coagulation under different conditions, a series of membrane filtration was performed to get information on how much of membrane fouling was reduced. The membrane fouling decreased as the ${\rho}_i$ and t increased but as MLSS decreased. Total fouling resistances, Rt (=Rc+Rf) were calculated and compared to those of the controls (Ro), which were obtained from the experiments without electro-coagulation. A kinetic approach for the fouling reduction rate (Rt/Ro) was carried out and three equations under different MLSS concentration were suggested: i) ${\rho}_i^{0.39}t=3.5$ (MLSS=4500 mg/L), ii) ${\rho}_i^{0.46}t=7.0$ (MLSS=6500 mg/L), iii) ${\rho}_i^{0.74}t=10.5$ (MLSS=8500 mg/L). These equations state that the product of ${\rho}_i$ and t needed to reduce the fouling in certain amounts (in this study, 10% of fouling reduction) is always constant.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.210-210
• /
• 2013

그래핀은 뛰어난 기계적, 화학적, 광학적, 전기적 특성을 가지고 있는 2차원 물질로, 대면적 합성법과 전사 공정을 통해 다양한 기판에서의 사용이 가능해지면서 차세대 전자 소자로 활용하기위한 활발한 연구가 이루어지고 있다. 디스플레이, 태양전지의 전극과 전계 효과 트랜지스터의 채널로 적용한 연구에서 우수한 결과들을 보이고 있다. 특히, 금속/금속 산화물 전극은 염료 감응형 태양전지와 유기 발광 다이오드 구조에서 화학적으로 불안정할 뿐 아니라 일함수가 고정되어 쇼트키 접촉이 형성되면 저항을 낮추기 어렵지만, 그래핀은 금속/금속 산화물 전극보다 화학적으로 안정하고 일함수의 조절이 가능해 옴 접촉 형성에 용이하다. 그래핀의 일함수를 조절하는 연구는 크게 공유결합과 비공유 결합을 이용한 방법이 시도된다. 공유 결합을 이용한 방법은 합성과정에서 그래핀의 구조에 내재된 결함 혹은 새로운 결함을 형성하여 다른 원소를 첨가하는 방법이다. 이러한 방법은 그래핀의 결함 영역에서 작용하기 때문에 그래핀 전자 구조의 높은 수준 조절을 위해선 그래핀 구조의 파괴가 동반된다. 반면, 비공유 결합을 이용한 방법은 전하 이동 도핑 효과를 이용해 그래핀의 전자 구조를 제어하는 방법으로, 금속/금속산화물/기능기와 그래핀의 적층으로 복합 구조를 형성하는 방법이다. 금속/금속 산화물과의 복합구조는 안정적인 p-형 도핑이 보고되었지만, n-형 도핑은 대기중의 수분, 산소 그리고 기판과의 상호작용에 의해 대기중에서 불안정해 추가적인 피막공정이 요구된다. 기능기를 이용한 적층 구조는 그래핀과 기판사이의 상호작용 혹은 그래핀 전자 구조를 다양한 기능기를 이용해 제어하는 것으로, 이극성을 가진 자기정렬 단일층(self-assembled monolayers)이 대표적인 방법이다. 공간기(spacer)의 길이나 말단기(end group)의 종류로 p-형과 n-형의 도핑 수준을 제어할 수 있지만, 흡착기(chemisorbing groups)의 반응성이 기판의 화학적, 물리적 표면상태에 의존하기때문에 기판 선택이 제약되며 전처리 공정이 요구될 수 있는 한계가 있다. 본 연구에서는 다양한 기판에 적용가능한 용액 공정을 이용해 그래핀과 고분자를 적층하였고, 안정적이고 효과적으로 일함수를 낮추는 구조를 확인하였다.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.2
• /
• pp.31-43
• /
• 2019

In this study, polymer elastic bumps were fabricated for the flexible electronic package flip chip bonding and the viscoelastic and viscoplastic behavior of the polymer elastic bumps according to the temperature and load were analyzed using FEM and experiments. The polymer elastic bump is easy to deform by the bonding load, and it is confirmed that the bump height flatness problem is easily compensated and the stress concentration on thin chip is reduced remarkably. We also develop a spiral cap type and spoke cap type polymer elastic bump of $200{\mu}m$ diameter to complement Au metal cap crack phenomenon caused by excessive deformation of polymer elastic bump. The proposed polymer elastic bumps could reduce stress of metal wiring during bump deformation compared to metal cap bump, which is completely covered with metal wiring because the metal wiring on these bumps is partially patterned and easily deformable pattern. The spoke cap bump shows the lowest stress concentration in the metal wiring while maintaining the low contact resistance because the contact area between bump and pad was wider than that of the spiral cap bump.

• Korean Chemical Engineering Research
• /
• v.51 no.6
• /
• pp.766-773
• /
• 2013

A transparent film was fabricated based on bacterial cellulose (BC), BC has excellent physical strength and stability at high temperature and it is an environmental friendly flexible material. In order to improve the conductivity, silver nanowire (AgNW) and/or graphene were introduced to the BC membrane. The aspect ratio of the AgNW synthesized in this study was 214, with a length of $15{\mu}m$ and width of 70 nm. The higher aspect ratio improved the conductivity by reducing the contact resistance. The thermal and electrical properties of 7 types of films prepared were investigated. Each film was fabricated with rectangular shape ($2mm{\times}2mm{\times}50{\mu}m$). The films were scored with a net shape by a knife, and filled with AgNW and graphene to bestow conductivity. The film filled with AgNW showed favorable electrical characteristics with a thickness of $350{\mu}m$, electron concentration of $1.53{\times}10^{19}$, electron mobility of $6.63{\times}10^5$, and resistivity of 0.28. The film filled with graphene had a thickness of $360{\mu}m$, electron concentration of $7.74{\times}10^{17}$, electron mobility of 0.17, and resistivity of 4.78. The transmittances at 550 nm were 98.1% and 80.9%, respectively. All the films were able to light LEDs bulbs although their brightness differed. A thermal stability test of the BC and PET films at $150{\pm}5^{\circ}C$ showed that the BC film was more stable, whereas the PET film was quickly banded. From these results, it was confirmed that there it is possible to fabricate new transparent conductivity films based on BC.

• Journal of Sensor Science and Technology
• /
• v.9 no.3
• /
• pp.224-232
• /
• 2000

Aluminum metal process in surface micromachining enables to fabricate Al electrodes or Al structures, which improve electrical characteristics by reducing contact- and line-resistance or makes the whole process to be simple by using oxide as sacrificial layer. However, it is not possible to use conventional sacrificial layer etching process, because HF solution attacks aluminum as well as sacrificial oxide. The mixed solution of BHF and glycerine as an alternative shows the adequate properties to meet with this end. The exact etching properties, however, are sensitively depends on the geometry of the released structure, because the most etching process of sacrificial layer proceeds to the lateral direction in narrow space. Also, the surface roughness of aluminum affects to the etching characteristics. This paper reports experimental results on the effect of microstructure and surface roughness of aluminum to the etching properties. Considering these effects, we propose the optimized etching condition, which can be used practically for the fabrication of aluminum electrodes and microstructures by using standard surface micromachining process without modification or additional process.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.78.2-78.2
• /
• 2012

최근 PRAM의 집적도 향상 및 3차원 적층에 의한 메모리 용량 향상을 위해 셀 선택 스위치로서 박막형 Ovonic Threshold Switching (OTS) 소자를 적용한 Cross bar 구조의 PRAM이 제안된 바 있다. OTS 소자는 비정질 칼코지나이드를 핵심층으로 하는 2단자 소자로서 고저항의 Off 상태에 특정 값 (문턱스위칭 전압) 이상의 전압을 가해주면 저저항의 On 상태로 바뀌고 다시 특정 값 (유지전압) 이하로 전압을 감소시킴에 따라 고저항의 Off 상태로 복원하는 특성을 갖는다. 셀 선택용 스위치로 적용되기 위해서는 핵심적으로 On-Off 상태간의 가역적인 변화 중에도 재료가 비정질 구조를 안정하게 유지해야 하며 전기적으로는 Off 상탱의 저항이 크고 또한 전류값의 점멸비가 커야 한다. GeSe는 이원계 재료로서 단수한 구성에도 불구하고 OTS 소자가 갖추어야할 기본적인 특성을 가지는 것으로 알려져 있다. 본 연구에서는 GeSe로 구성된 OTS 재료에 경원소인 질소를 첨가하여 비정질 상태의 안정성과 소자특성의 개선 효과를 조사하였다. RF-puttering 시 Ar과 $N_2$의 혼합 Gas를 사용하여 조성이 $Ge_{62}Se_{38}$ ($N_2$ : 3%)인 박막을 제작하여 DSC를 통해 결정화온도(Tx)를 확인하였고, $N_2$ gas의 함유량이 각각 1 %, 2 %, 3 %인 $Ge_{62}Se_{38}$인 박막을 전극의 접촉 부 면적이 $10{\times}10\;{\mu}m^2$인 cross-bar 구조의 소자로 제작하여 Threshold switching voltage ($V_{th}$), Delay time ($t_d$), $I_{on}/I_{off}$ 그리고 Endurance 특성을 평가하였다. DSC 분석 결과 $N_2$ 가 3 % 첨가된 GeSe 박막은 Tx가 $371^{\circ}C$에서 $399^{\circ}C$로 증가되었다. $N_2$가 1% 첨가된 GeSe 소자를 측정한 결과 $V_{th}$의 변화 없는 가운데 $I_{on}/I_{off}$이 약 $2{\times}10^3$에서 $5{\times}10^4$로 향상되었다. Endurance 특성 역시 $10^4$에서 $10^5$번으로 향상되었다. $t_d$의 경우 비정질 상태의 저항 증가로 인해 약 50% 증가되었다. 이러한 $N_2$의 첨가로 인한 비정질 GeSe 박막의 변화 원인에 대한 분석 결과를 소개할 예정이다.

• Journal of the Society of Disaster Information
• /
• v.13 no.3
• /
• pp.305-312
• /
• 2017

In our society, the advanced, advanced, and information industries have continued to grow and now live in the era of the fourth industrial revolution. As the industry develops, the load of the users has also increased so much that it is deepened by the energy shortage phenomenon and the construction of additional energy facilities is required. Therefore, energy plant construction work is being actively carried out in the coastal area. In particular, it is common to build a plant in the ground by filling the coast with soil in other regions, reflecting the fact that Korea is lacking in the country when constructing power plants, gas and petrochemical plants. Current domestic grounding designs are designed or constructed to suit only the use of grounding resistors based on the electrical equipment design technical standards. However, in the case of a plant facility constructed in the untested buried soil, when the lightning current and the abnormal current are inputted, the facility operator or the user due to the elevation of the ground potential is seriously exposed to the risk of electric shock disaster. In this paper, we analyze the ground resistivity of the landfilled soil and use a computer program (CDEGS) based on KS C IEC 61936-1, We analyze the contact voltage and stratification voltage and propose a grounding design optimized for plant installation.

• Journal of the Korean Electrochemical Society
• /
• v.26 no.1
• /
• pp.1-10
• /
• 2023

The cathode, which is one of the four major components of a lithium secondary battery, is an important component responsible for the energy density of the battery. The mixing process of active material, conductive material, and polymer binder is very essential in the commonly used wet manufacturing process of the cathode. However, in the case of mixing conditions of the cathode, since there is no systematic method, in most cases, differences in performance occur depending on the manufacturer. Therefore, LiMn₂O₄ (LMO) cathodes were prepared using a commonly used THINKY mixer and homogenizer to optimize the mixing method in the cathode slurry preparation step, and their characteristics were compared. Each mixing condition was performed at 2000 RPM and 7 min, and to determine only the difference in the mixing method during the manufacture of the cathode other experiment conditions (mixing time, material input order, etc.) were kept constant. Among the manufactured THINKY mixer LMO (TLMO) and homogenizer LMO (HLMO), HLMO has more uniform particle dispersion than TLMO, and thus shows higher adhesive strength. Also, the result of the electrochemical evaluation reveals that HLMO cathode showed improved performance with a more stable life cycle compared to TLMO. The initial discharge capacity retention rate of HLMO at 69 cycles was 88%, which is about 4.4 times higher than that of TLMO, and in the case of rate capability, HLMO exhibited a better capacity retention even at high C-rates of 10, 15, and 20 C and the capacity recovery at 1 C was higher than that of TLMO. It's postulated that the use of a homogenizer improves the characteristics of the slurry containing the active material, the conductive material, and the polymer binder creating an electrically conductive network formed by uniformly dispersing the conductive material suppressing its strong electrostatic properties thus avoiding aggregation. As a result, surface contact between the active material and the conductive material increases, electrons move more smoothly, changes in lattice volume during charging and discharging are more reversible and contact resistance between the active material and the conductive material is suppressed.

• Journal of Adhesion and Interface
• /
• v.10 no.2
• /
• pp.90-97
• /
• 2009

Dispersion and self-sensing evaluation for single-carbon fiber reinforced in three different acid-treated CNT-epoxy nanocomposites were investigated by electro-micromechanical techniques and wettability tests. Self-sensing based on contact resistivity exhibited more noise for single carbon fiber/acid-treated CNT-epoxy composites than it did for untreated CNT. However, the apparent modulus was higher the acid treated case than the untreated case which is attributed to better stress transfer. The interfacial shear strength (IFSS) between carbon fibers and the CNT-epoxy was lower than that between carbon fiber and neat epoxy due to the increased viscosity associated with the addition of the CNT. The CNT-epoxy nanocomposite exhibited more hydrophobicity than did neat epoxy. Change in the thermodynamic work of adhesion was consistent with changes in the IFSS but disproportional to that of the apparent modulus. The optimum condition of acid treatment on the need can be obtained instead of the maximum condition.

• Korean Journal of Optics and Photonics
• /
• v.23 no.2
• /
• pp.64-70
• /
• 2012

We analyzed the changes in electrical and optical characteristics of 1 $mm^2$ multiple-quantum-well (MQW) blue LEDs grown on a c-plane sapphire substrate after a stress test. Experiments were performed by injecting 50 mA current for 200 hours to TO-CAN packaged sample chips. We selected the value of injection current for stress through the junction-temperature measurement by using the forward-voltage characteristics of a diode to maintain a sufficiently low junction temperature during the test. The junction temperature at the selected injection current of 50 mA was 308 K. Experiments were performed under the assumption that the average junction temperature of 308 K did not affect the characteristics of the ohmic contact and the GaN-based materials. Before and after the stress test, we measured and analyzed current-voltage, light-current, light distribution on the LED surface, wavelength spectrum and relative external quantum efficiency (EQE). After the stress test, it was observed experimentally that the optical power and the relative EQE decreased. We theoretically investigated and experimentally proved that these phenomena are due to the increased nonradiative recombination rate caused by the increased defect density.