• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.9
• /
• pp.388-394
• /
• 2003

Many toxic pesticides as aqueous-base sprays are dispensed for protection of food crops from pests into farm fields. When dispensed with conventional nozzles, a large portion of the spray is often lost by airborne drifts of droplets away and lack of deposition onto the plants due to rapid gravitational settling of droplets to the soil beneath. And target deposition efficiencies poorer than 20％ are often encountered in agricultural pesticides. An electrostatic spraying technology offers a very favorable means to increasing pesticides droplets deposition onto biological surfaces of living crops. In this paper a corona type spray nozzle, utilizing a set of corona charging devices and a pulsed droplet-charging voltage applied, has been proposed and tested its potential experimentally. As a result, it exhibits a large current deposition of aqueous pesticide sprays on the sensing target, which, however, promise to be as one of the effective electrostatic spraying nozzle.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.12
• /
• pp.573-578
• /
• 2003

In this study, new type of induction charging system for electrostatic spraying was manufactured and proposed to improve the electrical safety and charging efficiency. And parameters of proposed system to generate the maximum deposition current with electrical safety were selected and investigated. The selected parameters were frequency of square pulse and thickness of insulation material, outer diameter of device and thickness and positions of electrode. Charging quantity of water drop was measured by deposition current detected from sensing plate indirectly. The maximum deposition current for each parameter were 3.5[uA] at the frequency of 15[kHz] and thickness of 0.25[mm] insulating layer. And maximum deposition currents were 2.8[uA] and 3.0[uA] at 25[mm] outer diameter of charging device and 0.25[mm] thickness of electrode each. Effects of electrode position from spraying nozzle on deposition current was a little.

• Journal of ILASS-Korea
• /
• v.23 no.3
• /
• pp.114-121
• /
• 2018

FT process is a technology of chemical reactions that converts a mixture of carbon monoxide and hydrogen into liquid hydrocarbons. During the FT process unreacted gas, known as Off-gas which has low-calorie, is discharged. In this study, we developed an engine that utilize simulated Off-gas, and studied the characteristics of the engine. The off-gas composition is assumed to be $H_2$ 70%, CO 15%, $CO_2$ 15% respectively. Under stoichiometric air-fuel ratio, the experiment was conducted at WOT and IMEP 0.3 Mpa changing compression ratio. Ignition timing was applied with MBT timing. Maximum indicated thermal efficiency 37% was achieved at compression ratio 15 under WOT. CO, $CO_2$ and $NO_x$ were influenced by changing compression ratio, and CO emission was satisfied with the US Tier 4 standard for nonroad engine over the entire experimental conditions.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.112-112
• /
• 2003

은분말은 전자 산업에 있어 후막 도체 페이스트의 제조를 위해 사용되어지고 있다. 후막 페이스트는, 기재상에 스크린 프린트되고, 전도성의 회로 패턴을 형성한다. 이러한 회로는, 다음에 건조, 소성되고 액체 유기 비이클을 휘발 시키고, 그리고 은 입자를 소결시킨다. 프린트 회로 기술은 점점 고밀도이면서 더욱 정밀한 전자 회로를 요구하고 있다. 이러한 요건에 적합하기 위하여 도선은 폭이 점점 좁아지고, 선의 사이의 거리가 점점 작아지고 있다. 고밀도가 조밀하게 꽉 찬 좁은 선을 위하여 은 분말은 가능한 크기가 단일하고 구형의 형태를 가져야 한다. 현재 금속 분말을 제조하는 방법으로는 화학적 환원법, 무화 또는 분쇄, 열분해법등의 물리적 과정 및 전기 화학적 과정 등이있다. 본 연구에서는 입도 분포가 좁은 구형의 은 분말을 제조하기 위하여 기상법의 하나인 분무열분해법을 도입하였다. 또한 싸이클론을 사용하므로 큰 액적들을 걸러 입도 분포를 줄였다. 은 분말의 프리커서로써는 AgNO$_3$를 사용하였고 반응기의 온도는 $700^{\circ}C$에서 100$0^{\circ}C$까지 변화시켰으며 운반기체로써는 5%H$_2$ 혼합가스로 20L/min에서 80L/min 변화시켜 은 분말을 제조하였다. 또한 용액의 농도는 0.2M에서 1.0M까지 변화시켰다. 용액의 농도가 0.2M이고 운반기체의 유랑이 40L/min일 경우 완전한 은 상이 관찰되었고, 입자의 크기는 약 600nm였다.

• Journal of ILASS-Korea
• /
• v.27 no.1
• /
• pp.11-17
• /
• 2022

In upcoming Post Stage-V and Tier 5 regulations of construction machineries, nitrogen oxide (NOx) emissions are strictly limited in cold start conditions. In response to this, a method of improving NOx conversion efficiency has been applied by installing an electric heating catalyst (EHC) in front of conventional urea-SCR systems so that the evaporation and thermal decomposition of urea-water solution can be promoted in cold start conditions. In this strategy, the evaporation and thermal decomposition of urea-water solution and corresponding NOx conversion efficiency are governed by temperature conditions inside the EHC. Therefore, characterizing the temperature distribution in the EHC under various operating conditions is crucial for the optimized operation and control of the EHC in Urea-SCR systems. In this study, a 1-D modeling analysis was performed to predict the heater surface temperature distribution in EHC under various operating conditions. The reliability of prediction results was verified by comparing them with measurement results obtained using an infrared (IR) camera. Based on 1-D analysis results, the effects of various EHC operation parameters on the heater surface temperature distribution were analyzed and discussed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.4
• /
• pp.184-189
• /
• 2002

The electrical and optical properties of $(Pb_{0.91}La_{0.09})(Zr_{0.65}Ti_{0.35})O_3$(PLZT) thin films by MOCVD using ultrasonic spraying were investigated. To compensate the Pb loss by evaporation, 5 and 10 wt% of excess Pb was added to 0.2 M precursor. After deposition of films on ITO-coated glasses in oxygen atmosphere for 30 min, films were heated by in-situ RTA (rapid thermal annealing) method. When the films were heat treated at $600^{\circ}C$, perovskite single phase was obtained. The optical property of the film with 10 wt% excess Pb was excellent showing about 84 % of transmittance near 520 nm. The dielectric constant of the film was about 308 and the leakage current of the film was lower than the Pb excess 0, 5 wt% PLZT thin films.

• Journal of the Korean Electrochemical Society
• /
• v.19 no.2
• /
• pp.50-56
• /
• 2016

Spherical lithium manganese oxide spinel, $Li_{1.10}Mn_{1.86}Al_{0.02}Mg_{0.02}O_4$ was prepared by wet-milling, spray-drying, and sintering process. In the spray-drying process, solid content in slurry was varied from 20 to 30 wt%. In the sintering process, the precursors have been sintered under air or $O_2$ atmosphere. While the as-prepared samples exhibit excellent electrochemical properties at room temperature, the discharge voltage profiles at 5.0C are very different one from another. The origin for the difference especially at initial state of discharge is oxygen defect. The sample prepared in air has larger capacity related to the plateau at 3.3 V (vs. $Li/Li^+$) which is caused by the oxygen defects than the one prepared in $O_2$. The difference of discharge voltage profiles especially at the final state of discharge comes from different diffusion rate of $Li^+$ ions. The sample prepared from 30 wt% solid content of slurry shows twice higher diffusion rate than the samples prepared from 20 wt% solid content, which is attributed to better compactness between primary particles for the sample prepared from 30wt % solid content than the one prepared by 20 wt%.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1994.04a
• /
• pp.10-15
• /
• 1994

전기도금 공정에서 발생하는 수소취성은 다량의 수소이온이 강제품에 흡수되어 취화되는 현상을 나타내는 것으로 인장강도 200KSI 이상이 요구되는 항공기용 또는 로켓트 추진기관용 초고강도강에서 크게 문제가 되고 있다. 본 내용은 전기 카드뮴도금 작업시에 발생되는 수소취성에 대하여 간략하게 기술하고. 이 수소취성을 제거하는 방법 및 수소취성을 저게 생성시키는 저취성도금인 Cd-Ti 합금도금의 공정개발 결과를 보고한다. 실험결과에 의하면 도금층의 Ti함량은 0.1-0.7%이며 Ti의 공석에 의하여 Cd 도금에 비하여 저취성을 나타냈으며, Cd-Ti합도금의 내식성은 상대평가인 염수분무시험 결과 Cd도금과 비교하여 소재표면의 부식을 일으키는 붉은녹발생까지의 시간이 500시간으로 보다 높은 내식성을 나타내었다. 그리고 Cd-Ti 합금의 공정표준 및 Ti농도의 관리방법 등을 정리하여 보고한다.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.267-270
• /
• 2007

오존무 분사장치는 흡입구와 내에 소정의 공간이 형성된 케이스와 자동 손잡이와 $360^{\circ}$회전이 가능해 운반 및 이동이 간편한 케이스, 상기 케이스의 내부 소정 부위에 공기 흡입구로 흡입되는 공기 중에 포함된 먼지 및 습기를 제거하는 제습 장치와, 원료가스인 공기를 일정하게 제공하는 송풍기, 강력한 살균 소독기능을 지닌 오존발생기, 오존을 발생시키기 위한 고주파 펄스 전원장치, 입자경이 $3{\sim}40{\mu}m$이하의 이류체 미세 분사형 노즐, 살수통(물을 담는 용기) 및 기능 조절부(펄스전원제어, 타이머 조절, 송풍기 제어, 이류체 미세 분사형 노즐스위치 제어)로 성되어 작동하는 것으로 일반적인 가습기와는 다르다. 그리고 강력한 살균, 소독, 탈취 및 대기의 정화 기능이 있는 오존을 이용하는 동시에 기존의 방식보다 간단한 구조의 분무발생 수단을 구비함으로써 전체적으로 구성을 간단하게 하면서 대기 정화 효율을 향상시키는 장점이 있다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.1060-1062
• /
• 2002

Spherical and dense BAM phosphor particles were prepared by spray pyrolysis. The key idea of dense BAM particles is to lead gelation in droplets, which was successfully achieved by using the aluminum polycation as the precursor solution for the spray pyrolysis. The BAM phosphor particles prepared by spraying the aluminum polycation solution have completely spherical shape and dense structure. When directly applied to make phosphor film on the glass by the screen-printing method, the prepared spherical BAM phosphor particles showed better packing density and surface morphology than that of commercial one, which has irregular shape and large particle size. It was also found that the thermal degradation in the photoluminescence intensity for dense and spherical BAM particles was less than that of commercial one.