• Korean Chemical Engineering Research
• /
• v.49 no.1
• /
• pp.15-20
• /
• 2011

The contamination effect of toluene in the airstream on PEM fuel cell performance was studied with various toluene concentration under different operation conditions. And the recovery of the cell performance by applying clean air and the removal of toluene in the air by adsorption of active carbon were investigated. The toluene concentration range used in the experiments was from 0.1 ppm to 5.0 ppm. The performance degradation and recovery were measured by constant-current discharging and electrochemical impedance spectroscopy(EIS). Toluene adsorption capacity of KOH impregnated active carbon was obtained from the adsorption isotherm curve. The severity of the contamination increased with increasing toluene concentration, current density and air stoichiometry, but decrease with increasing relative humidity. The cell performance was recovered by toluene oxidation with oxygen and water in humidified neat air. EIS showed that the increase of charge transfer resistance due to toluene adsorption on Pt surface mainly reduced the performance of PEMFC. Toluene adsorption capacity of active carbon decreased as KOH weight increased in KOH impregnated active carbon.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.10
• /
• pp.709-716
• /
• 2011

Effect of inorganic coagulants dosing on the performance of electro-chemical process was studied when treating hospital wastewater having low electrolyte concentration. It is thought that adding inorganic coagulants caused increase in concentration of electrolyte and this caused increase in free chloride concentration and consequently, caused increase in indirect oxidation effect. Thus, COD removal efficiencies more than doubled in percentage terms at the 2 hrs of reaction time and current density of $1.76A/dm^2$ compared with the results obtained from the parallel experiments without adding inorganic coagulants. T-N removal efficiencies approximately doubled in percentage terms at the 2 hrs of reaction time and 700 ppm of coagulants addition and applied current density of $1.76A/dm^2$ due to the increase of free residual chlorine such as HOCl caused by increase of electrolyte concentration through the addition of inorganic coagulants. Under the same experimental condition, more than 90% of T-P removal efficiencies was obtained. The reason can be explained that increase of chemical adsorption rate between phosphate and insoluble metal compounds caused by dissolved oxygen generated from anode by the increased electrolyte concentration through inorganic coagulants addition make a major role in improving T-P removal efficiencies. It can be concluded that inorganic coagulants addition as the supplemental agent of electrolyte is effective way in improving organic and nutrient salt removal efficiency when treating hospital wastewater having low electrolyte concentration.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.194-194
• /
• 2015

본 연구에서는 PVD법 중의 하나인 스퍼터링(sputtering) 기술을 이용하여 향상된 희생양극(sacrificial anode)적 특성을 가지는 Al-Mg 막을 제작함은 물론 그 제작조건, 표면의 몰포로지, 결정구조학적 결정배향성과의 연관성을 해석 및 전기화학적 내식특성평가 등을 통하여 종합적인 결과를 고찰-정리해 보았다. 이를 통해 박막의 증착과정 중 가스압의 변화가 흡착 인히비터로 작용하여 박막의 몰포로지와 결정배향성에 미치는 영향을 분석하였으며 이러한 표면 몰포로지, 결정배향성과 내식성간 상관관계를 해석하여 최적의 Al-Mg 막 설계 지침을 제시하고자 하였다.

• Journal of the Korean Institute of Gas
• /
• v.9 no.4 s.29
• /
• pp.11-16
• /
• 2005

In this paper, the hydrogen osmosis test and the mechanical tensile test were carried out to examine hydrogen cracking behavior of STS444 with welding conditions. In $0.5MH_2SO_4+0.001M \;As_2O_3$ solution, the hydrogen embrittlement characteristics of weld zone of STS444 added to load of $1,400 kg/cm^2$ together with hydrogen osmosis by current of $30mA/cm^2$ for 60 min. was considered. As a result of study on the hydrogen embrittlement and mechanical characteristics of STS444외와 with welding conditions the tensile stress and elongation of STS444 get lower by the absorption of oil or water before welding. Also, the reduction rate of tensile stress and elongation of STS444 is larger because of hydrogen embrittlement by the absorption of oil or water. STS444 by the absorption of water before welding is more sensitive to hydrogen embrittlement than oil.

• Composites Research
• /
• v.33 no.6
• /
• pp.336-340
• /
• 2020

In this study, carbon aerogels (CA) were prepared by sol-gel polycondensation of resorcinol and furfural in isopropanol using hexamethylenetetramine as a catalyst, and then directly drying the organic gels under isopropanol freeze-drying conditions, followed by carbonization under a nitrogen atmosphere. The preparation conditions of the CA were explored by changing the mole ratio of resorcinol to furfural. The effect of the preparation conditions on the pore structure of the CA was studied by nitrogen adsorption isotherms. The characteristics of the CA were studied by scanning and transition electron microscopy, and infrared spectrometry. The accessibility of pores and performance of the CA as an electrode in electric double layer capacitors were also electrochemically investigated. As a result, BET surface area and specific capacitance increased with the molar ratio of resorcinol to catalyst (R/C) ratio; the maximum values of 765 ㎡/g and 132 F/g were achieved at the R/C ratio of 200, respectively. Consequently, it was confirmed that increasing the R/C ratio increased the average pore size of the CA electrode, which improved the rate capability of the system.

• Journal of the Korean Electrochemical Society
• /
• v.17 no.3
• /
• pp.164-171
• /
• 2014

A highly sensitive and selective non-enzymatic glucose sensor has gained great attention because of simple signal transformation, low-cost, easily handling, and confirming the blood glucose as the representative technology. Until now, glucose sensor has been developed by the immobilization of glucose oxidase (GOx) on the surface of electrodes. However although GOx is quite stable compared with other enzymes, the enzyme-based biosensors are still impacted by various environment factors such as temperature, pH value, humidity, and toxic chemicals. Non-enzymatic sensor for direct detecting glucose is an attractive alternative device to overcome the above drawbacks of enzymatic sensor. Many efforts have been tried for the development of non-enzymatic sensors using various transition metals (Pt, Au, Cu, Ni, etc.), metal alloys (Pt-Pb, Pt-Au, Ni-Pd, etc.), metal oxides, carbon nanotubes and graphene. In this paper, we show that Ni-based nano-particles (NiNPs) exhibit remarkably catalyzing capability for glucose originating from the redox couple of $Ni(OH)_2/NiOOH$ on the surface of ITO electrode in alkaline medium. But, these non-enzymatic sensors are nonselective toward oxidizable species such as ascorbic acid the physiological fluid. So, the anionic polymer was coated on NiNPs electrode preventing the interferences. The oxidation of glucose was highly catalyzed by NiNPs. The catalytically anodic currents were linearly increased in proportion to the glucose concentration over the 0~6.15 mM range at 650 mV versus Ag/AgCl.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.42-42
• /
• 2007

티타네이트 나노튜브는 10 nm 이내의 내경과 0.74nm 정도의 크기를 갖는 층상 구조를 이루고 있어 높은 비표면적을 이용한 수소의 물리적 흡착뿐만 아니라 Ti-H 결합에 의한 화학적 흡착이 동시에 가능하다. 따라서 본 연구에서는 전이금속 원소 중 Ni을 첨가한 티타네이트 나노튜브를 합성하고 수소저장특성을 평가하고자 하였다. 티타네이트 나노튜브는 저온균일침전법으로 제조된 침상형의 $TiO_2$ 분말을 출발원료로 염화니켈을 $TiO_2$의 질량 비로 1~5wt% 첨가하고 10 M의 NaOH 수용액에서 일정시간 혼합한 후 $150^{\circ}C$에서 24시간 수열합성하였다. 합성된 분말의 입자형상 및 결정상은 전자현미경과 X-선 회절 시험을 이용하여 분석하였고, 입자의 비표면적은 액체질소흡착법을 이용하여 측정하였다. 전자현미경 관찰결과 이온교환 전후의 입자형상은 큰 변화가 없었던 반면 이온교환 후 입자의 비표면적이 30% 이상 증가함을 확인하였다. 특히 Ni의 도핑량이 증가함에 토라 입자의 비표면적도 함께 증가하였으며, 전자현미경 관찰결과 더욱 미세한 나노튜브가 형성됨을 확인할 수 있었다. P-C-T를 이용하여 측정한 순수한 티타네이트 나노튜브의 수소저장량이 20기압에서 1.2 wt% 정도로 측정된 반면 Ni이 5 wt% 첨가된 티타네이트 나노튜브의 경우 같은 압력에서 1.6 wt%를 나타내었다.

• Korean Journal of Soil Science and Fertilizer
• /
• v.16 no.4
• /
• pp.318-324
• /
• 1983

Electrochemical properties of Georgia kaolinite in aqueous suspension were studied by ion adsorption, potentiometric titration, and electrophoretic mobility measurements. Kaolinite in 0.001 M and 0.1 M NaCl solution showed qualitatively both pH independent and pH depender negative and positive charges through pH range 2.5-11.0 when dissolved aluminum ions from kaolinite were considered as well as $Na^+$ and $Cl^-$ as index ions. Electrophoretic mobilities (EM) of 0.02 wt. % kaolinite suspension in distilled water and 0.001 M NaCl solution were approximately constant against mobility measuring time consumed in the electrophoresis cell at different pH values, and isoelectric points(IEP) were around pH 4.7. EM values in 0.1 M NaCl solution were positive and constant against mobility measuring time below pH 4; but above pH 4, EM values were negative for the first 10 seconds followed by positive values which became approximately constant through stepped changes after 10 minutes. Hydrated cations may bind to the six- member oxygen ring sites having multiple partial negative charges on the exterior tetrahedral layer surface by both electrostatic and hydrogen bonding force while hydrated anions bind to the partially positively charged hydrogen atoms on the exterior octahedral layer surface. Parts of the aluminol groups on the exterior octahedral layer surface as well as edge faces may be involved in complex reactions and have both anion and cation exchange capacities in the electrolyte solution above pH 4.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.5
• /
• pp.750-759
• /
• 2016

The $MnO_2$ electrodeposited on the surface of the carbon nanofiber mats ($MnO_2$-LCNFM) were prepared from electrospun lignin-g-PAN copolymer via heat treatments and subsequent $MnO_2$ electrodeposition method. The resulting $MnO_2$-LCNFM was evaluateed for its potential use in a supercapicitor electrode. The increase of $MnO_2$ electric deposition time was revealed to increase diameter of carbon nanofibers as well as $MnO_2$ content on the surface of carbon nanofiber mats as confirmed by scanning electon microscope (SEM) analysis. The electrochemical properties of $MnO_2$-LCNFM electrodes are evaluated through cyclic voltammetry test. It was shown that $MnO_2$-LCNFM electrode exhibited good electrochemical performance with specific capacitance of $168.0mF{\cdot}cm^{-2}$. The $MnO_2$-LCNFM supercapacitor successfully fabricated using the gel electrolyte ($H_3PO_4$/Polyvinyl alcohol) showed to have the capacitance efficiency of ~90%, and stable behavior during 1,000 charging/discharging cycles.

• Electrical & Electronic Materials
• /
• v.3 no.4
• /
• pp.332-338
• /
• 1990

본 연구는 절연유가 금속 파이프 중을 통과할 때 흐르는 유동전류 특성에 대하여 실험적으로 규명하였다. 유동전류는 파이프 길이, 절연유의 속도 및 온도에 따라 변하는 것이 관측되는데 파이프 길이가 4-6cm부근에서 피이크치가 나타나고 유속의 증가에 따라서는 선형적으로 증가하며 그리고 유의 온도가 약 50.deg.C 부근에서 또한 피이크가 나타나고 있다. 절연유에 전하를 주입시키는 수단으로 코로나 방전을 이용하였으며 부코로나 대전된 절연유의 유동전류가 코로나 대전 시키지 않은 절연유나 정코로나 대전된 절연유의 것보다 큰 값이 관측되었다. 이 결과로부터 고체 액체 접촉시 액체중의 음이온이 화학 포텐셜에 의하여 고체 표면에 흡착된다는 사실과 유동전류의 방향 및 발생기구를 해석할 수 있다.